Atel AXIS V810A User manual

Models Covered:
Version 3.0
1. LCD Display
Displays Home, Device
Information, Hotspot login
information, and Online Portal
login information.
5. SIM Card Slot
Insert your 4FF SIM card into this
spring-loaded SIM slot. To
remove a SIM, press the edge of
the SIM inward and the SIM
would pop outward from the SIM
slot.
2. Power Button
Power the V810A On/Off by
pressing and holding this button
for up to 10 seconds. Short press
to wake up the screen.
6. Type-C Port
Use this port to connect the
USB-C cable to a wall adapter
for external power.
3. Battery Port
Battery port used to connect to
the NiMH rechargeable battery
pack (may be sold separately).
6. Ethernet Port (RJ45)
Insert an ethernet cable to this
port and plug the other end into
your computer for internet
access.
4. Reset Button
Use a pin to push and hold this
button for 3 seconds for a factory
reset.
8. Antenna Connector
Install an optional antenna (may
sold separately) to increase
signal strength. You may have to
pull off the back rubber cover
prior to installing.
A quick look at your device:
Model
LTE
Bands
V
810A
B
2/4/5/12/13/14/66/71
Meet Your Device
ATEL 1
4G LTE Fixed Wireless Access Router
1 2 3 4 5 6 7 8

Setting up your device:
Step 1: Insert a SIM (if applicable)
a) Remove the back cover.
b) Check for a pre-installed SIM card or install a
SIM card provided by your wireless carrier.
c) To install, insert the 4FF Nano SIM card into
the spring-loaded SIM slot as the image
shows. To remove a SIM, press the edge of
the SIM inward and the SIM will pop outward
from the slot.
As the device boots up, you will see the Welcome
screen on your V810A LCD display, followed by the
status bar display.
WARNING! Please only use the provided USB
adapter for your V810A. The use of other
incompatible adapters may cause damage to your
device and void the warranty.
Step 2: Install the NiMH Battery
1. Remove battery cover.
2. Properly align and install the NiMH battery (with
three pin sockets). Make sure to align the pin
sockets correctly.
3. Put the NiMH battery in place as shown below.
4. Replace the back cover of the V810A and make
sure it’s aligned with the bottom of the device.
Note: the NiMH Battery may be sold separately.
Step 3: Power on the Device
To connect your V810A to the power outlet, insert
your USB cable to the device USB-C port and plug
the other end into a wall adapter.
Press and hold the Power Button for up to 10
seconds on your V810A to turn on the device.

Step 5: Initial Activation
Once the above 4 steps are completed, with a
service plan subscription, your V810A should
automatically detect the wireless network and
activate the SIM card services. The wireless
network and signal strength indicator will appear
on the status bar of your Welcome Home screen.
It might take a few minutes for the initial
activation.
If your V810A cannot
detect any network
services or if you have
SIM card issues, please
contact your wireless
service provider.
Step 4: Connecting a Computer to your V810A
using an Ethernet Port for Internet Access
a) Complete Steps 1, 2 and 3 above.
b) Plug an ethernet cable to the RJ45 Ethernet port of
your V810A and plug the other end of the cable to the
Ethernet port of your computer.
Note: The computer and ethernet cables are not included.
Step 6: Using your V810A Hotspot Wi-Fi
a) Locate your Network Name (SSID) / Password from
your V810A LCD Display or device label under the
battery holder.
b) Open the Wi-Fi settings of your Wi-Fi capable devices.
c) Select the SSID of your V810A from the available
network list.
d) When prompted, enter the WiFi password of your
V810A.
尺寸：如图示，公差: 0~-0.1mm
Fonts: Proxima Nova Rg Regular
材质：白色PET
注：需打印
FCC ID: XYO-V810 Made in China
Model: V810A
IMEI: XXXXXXXXXXXXXXX
Online Portal http://192.168.0.1
User Name: admin
Password: 123456
SSID: V810_XXXX
WIFI Password: 123456
SKU: 800964010
35.6
21.6
R1
12.61.5
1.3

For more information
Please refer to your V810A User Manual for additional
information or visit the ATEL USA website Device and
Support pages at www.ATEL-USA.com.
@AsiatelcoUSA
@ATEL USA
@atel-asiatelco
@ATEL_USA
© 2023 Asiatelco Technologies, Inc. All Rights Reserved