ATL Berkshire 600 AG User manual

Berkshire 600 AG
Thank you for choosing a Berkshire 600 AG telephone. You have selected a carefully designed
telephone that incorporates the very latest technology, offering a stylish instrument, and providing
many years of excellent service.
This booklet will ensure you obtain the best use of your telephone.
User Guide
*Headset sold separately
Manufacturer’s
Declaration
ATL Telecom Limited declares that this
product is in conformity with the essential
requirements of the ‘R&TTE directive
1999/5/EC’
Note:AcopyoftheDeclarationofConformity
is available upon request from ATL Telecom
Limited.
ATL Telecom Limited
Fountain Lane
St Mellons
Cardiff
Wales
UK
CF3 0FB
Technical Support
Telephone: [phone]
Facsimile: [phone]
Email: [email protected]
www.atltelecom.com
1/411/001/610 Issue 01 Nov 2006

Preparing to use
your Berkshire 600
AG
INITIAL CHECK
Our telephones are checked, tested and
leave us in perfect condition. If yours is
damaged, please return it to your supplier
with proof of purchase, for a replacement.
TELEPHONE NUMBER LABEL
The telephone incorporates a label
underneath the handset for recording
frequently used telephone numbers. To
removetheplasticcover,operatetherelease
clip with your thumb nail and hinge upward.
CONNECTION
The Berkshire 600 AG telephone can be
connected either to a Direct Exchange Line,
or as an extension to a compatible company
exchange (PABX).
HANDSET CORD
This cord will require connection between
the telephone and handset. Take any end
of the handset cord, and locate the port
marked ‘HANDSET’ on the left hand side of
the Berkshire 600 AG, and simply push to
locate. Connect the other end to the base of
the handset to complete.
LINECORDS
The Berkshire 600 AG arrives with two
line cords for customer selection. Select
your required linecord (standard BS6312
BT-socket, or RJ45 socket for category 5
installations). The rear of the telephone has
a port marked ‘LINE’, plug your selected
linecord into this port rst, and the other end
to your telephone line termination point. An
RJ11 line cord is available as an option, ask
your supplier for details.
PLUG TOP POWER SUPPLY
A Plug Top Power Supply is provided to
power the ATL Berkshire 600AG.
WARNING – Without the Plug Top
Power Supply tted the ATL Berkshire
600 AG will automatically disable the
Bluetooth® Functionality, there will be
no Handsfree operation and the LCD will
not be available in all circumstances.
If the telephone has been in operation
without the Plug Top Power Supply when
the power is reconnected the Bluetooth®
functionality will be deactivated, details
on how to reactivate the Bluetooth®
feature can be found in a later section
of this User Guide under the heading,
Activating or deactivating the Bluetooth®
feature.
WALL MOUNTING KIT
Awall mounting kit is available as an option,
please contact your supplier for further
information.
Using your
Berkshire 600 AG
with the Handset
RECEIVING CALLS
Incoming calls will be announced by the
audible ringer and ashing LED. To answer
the call, simply lift the handset. This will
start the Call Timer, please refer to the LCD
section of this guide for more detail on how
to congure the viewing angle etc.

Safety Statement
The Plug Top Power Supply included with
your ATL Berkshire 600 AG serves as the
disconnection device; therefore a socket
outlet shall be installed near the equipment,
and shall be easily accessible. Disconnect
the line cord before attempting to remove
the plug top power supply input jack from
the telephone.
Guarantee
YourBerkshire600 AGtelephoneisdesigned
and manufactured to exacting quality
standards.ThisenablesATL TelecomLimited
to offer a 2 year guarantee from the date of
purchase. This guarantee protects against
faulty material or workmanship, applies to
the UK only and is not transferable.
The terms and conditions under which
the guarantee will be valid are as set out
overleaf.
Misuse or any modication carried
out to the telephone, or operation
other than in accordance with the
instructions supplied, will invalidate
the guarantee.
Damage arising from incorrect
installation, accidental damage or
consequential loss, are not covered
under the guarantee.
In the event of a fault developing
during the period of the guarantee,
the complete telephone should be
returned to your supplier, adequately
and safely packed, together with
proof of date of purchase.
The liability of ATL Telecom Limited
1.
2.
3.
4.
will be limited to the cost of repair or
complete replacement of the same
defectiveinstrument,atthediscretion
of the company. In the event that the
same item is not available, a suitable
alternate will be offered.
The terms of this guarantee do not
affect your statutory rights.
The Bluetooth®word mark and logos are
owned by the Bluetooth SIG, Inc. and any
use of such marks by ATL Telecom is under
licence. Other trademarks and trade names
are those of their respective owners.
ATL BERKSHIRE 600 AG
BLUETOOTH®Core Specication
V1.2
BLUETOOTH® Range up to 10
metres
5.
ADJUSTING YOUR RINGER-VOLUME
Theringervolumeiscontrolledbya3position
switch located at the rear of the telephone,
and indicated by the word ‘ringer’. Moving
through the settings from left to right they
are HIGH, MED and LOW.
ADJUSTING YOUR RINGER PITCH
The ringer pitch control is also a 3 position
switch located at the rear of the telephone,
and indicated by the words ‘RINGER
PITCH’. Settings from left to right are HIGH,
MED and LOW.
MAKING A CALL VIA THE HANDSET
Pick up the handset and listen for
dial tone
Dial the required telephone number
(Note: making external calls from a
company exchange (PABX) requires
the number to be prexed by an access
digit, notmally ‘9’)
Using your
Berkshire 600 AG
with Handsfree
Whether it’s having both hands available,
or conference calling with colleagues, the
speakerphone feature of the Berkshire
600 AG is seen by many as a valuable
benet. Operation is via the HANDSFREE
key, (providing the handset is left in place).
Speaker volume may be adjusted via the [+]
and [-] keys.
►
►
Using your
Berkshire 600 AG
with a Bluetooth®
Headset
BLUETOOTH®FUNCTION
The ATL Berkshire 600 AG can allow a
maximum of two Bluetooth®headsets to be
Paired at any one time and will maintain a
connection to the activated device providing
it’s available, i.e. switched on and within
service range. Once you select a Paired
headset as the working headset, and the
headset is turned on, the telephone can
detect the headset status automatically,
this means that if the headset is turned off,
running out of battery or out of service range
the telephone can detect there’s no headset
available. The telephone will attempt to
reconnect to this headset providing the
user hasn’t selected an alternative headset,
the telephone can detect the headset as
available immediately when its switched on,
or an out of range headset is back within the
telephone service area.
With the ATL Berkshire 600 AG in the “On-
Hook” mode, the [MUTE] key is dened as
the [PAIRING] key, which can activate the
pairing mode, cancel the pairing mode or
clear the paired list.
WhentheATLBerkshire600AGisinthe“On-
Hook” mode, the [VOLUME-] key is dened
as [1st HEADSET] key and [VOLUME+] key
actsasthe[2ndHEADSET] key,youcanuse
these two buttons to select which headset
should be used as the active headset.

PAIRING MODE
While the telephone is in the “On-Hook”
mode, Press and hold the [PAIRING] key
for 3 seconds to enter pairing mode, the
telephone will start to search for Bluetooth®
Headsets for 3 minutes, the LCD will show
PAIRING HEADSET, if there is a Bluetooth®
Headset within range and in pairing mode,
the telephone will discover it and display
it’s brand name on the LCD. The LCD will
now prompt you to enter the PIN Code for
the pairing process, the Default PIN Code is
0000, you can enter the correct PIN Code
and press [PAIRING] button to conrm or if
you don’t enter a PIN Code the request for
the code will timeout after 3 seconds. The
pairing procedure will be successful when
the Bluetooth®Headset has the same PIN
code and the telephone will show HEADSET
PAIRED, otherwise the telephone will show
PAIRING FAILED when the pair mode has
timed out.
If you plan to Pair a second Bluetooth®
Headset, repeat this procedure.
Note: If an attempt is made to Pair an addi-
tional Bluetooth®Headset, when two Head-
sets have been previously Paired, the LCD
will display PAIR LIST FULL, you must Clear
Paired Headsets before attempting to Pair a
new Headset.
EXIT PAIRING MODE
While the telephone is in the “On-Hook”
mode, press and hold the [PAIRING] key for
over 3 seconds to enter the Pairing Mode,
and then press [PAIRING] key again this
will cause the telephone to exit the Pairing
Mode, and the telephone will show CANCEL
PAIRING.
CLEAR PAIRED HEADSETS
While the telephone is in the “On-Hook”
mode, press and hold the [PAIRING] key
over 3 seconds to enter Pairing Mode,
and then press and hold [PAIRING] key for
over 3 seconds before the clearing pairing
procedure is successful, this operation
will clear the Paired Headset List, and the
telephone will show PAIRING CLEARED.
CLEAR PAIRED HEADSETS
INDIVIDUALLY
Whilethetelephoneisinthe“On-Hook”mode,
press and hold either the [1st HEADSET] or
[2nd HEADSET] for over 5 seconds, this
will delete this headset from paired list, the
telephone will show HEADSET REMOVED
and then NO HEADSET.
MULTIPLE HEADSETS FUNCTION:
TheATL Berkshire 600AG can support up to
two headsets, this means that the user can
Pair up to a maximum of two headsets and
the ATL Berkshire 600 AG will detect and
attempt to make a connection with one of
the Paired Headsets when the user selects
a working headset.
AUTO HEADSET DETECTION:
ThetelephonecandetectthePairedHeadset
status and prompt its status on the LCD
automatically, when the telephone is in the
“On-Hook” mode, the Bluetooth®Headset
connectingstatus is showas BLUETOOTH®
MODE or CONNECTING.
VIEWING PAIRED HEADSETS:
While the telephone is in the “On-Hook”
mode it’s possible to view which Bluetooth®
Headsets are Paired with the ATL Berkshire
600 AG by simply pressing the [VOLUME-]
key which will list the [1st HEADSET] or by
pressing [VOLUME+] key which will list the
handset. Default = 1s.
TBR TIME ADJUSTMENT
Transfer break times may be adjusted from
100~600ms. in increments of 100ms. First
conrm that the 2 position switch, identied
as RECALL on the rear of the phone, is set
to the ‘T’ position. Lift the handset, press
SET, TRANSFER, followed by a numeric
key (1~6), replace the handset. Default =
100ms.
PROGRAMMING PORT
The Berkshire 600 AG has an unidentied
port, alongside the other conguration
switches, at the rear of the telephone.
Programming of this port is limited to
technicians trained in its use.
Help
If the telephone appears to be faulty when
rst connected, a few simple checks may
help to identify some possible problems, as
listed below:
NO DIAL TONE
Check that the telephone plug is fully
inserted in the socket
If it is, try connecting the telephone
into another socket, if available. If
dial tone is now heard, the original
socket is faulty.
Alternatively, try connecting another
telephone into your socket. If this
telephone gives dial tone, then your
new telephone is probably faulty.
►
►
►
TRANSFER/RECALL KEY NOT WORKING
Change the recall selector switch
setting (T/E). If the transfer operation
is now satisfactory, the problem is
resolved.
Compliance Notes
The Berkshire 600 AG may be connected to
the following types of installation:
Direct Exchange Lines (DEL)
Compatible Private Automatic
Branch
Exchanges (PABX). Please contact
the supplier of your Berkshire 600
AG to conrm compatibility with your
PABX.
Whilst the Berkshire 600 AG is compliant as
an extension to a compatible PABX system,
it cannot be guaranteed to operate under all
possible conditions of connection. Any case
of difculty should be referred in the rst
instance to the supplier of your telephone.
Power Rating
Information – AC
Plug Top Adapter
Input 230V ~ 50 Hz, 50mA
Output 7.5V ~ 50Hz, 300mA
ATL recommends only using the approved
adapter supplied with this product (ATL Part
Number 5/500/100/064)
►
1.
2.

has the additional benet of being activated
by short ring burst MW signals - see website
for details.
In all cases, an LED in the top right hand
corner of the telephone is used to indicate
the selected functions and incoming calls.
Any questions you may have should be
directed in the rst instance to your telephone
supplier with details of your PABX.
Further concerns may also be addressed
by calling our Technical Support Dept. or
visiting our website, www.atltelecom.com
MODEM PORTS
Your Berkshire 600 AG comes with two
modem ports (BS6312 and RJ11) typically
used for a PC modem, or as points of
connection for additional telephones.
HEARING AID COMPATIBILITY
For hearing aid users, an inductive coupler
has been installed in the handset of the
Berkshire 600 AG, to improve audible
efciency.
Installation Notes
MESSAGE WAITING
MW3 is used by systems that use high
voltage DC signalling. MW8/10 however
use line reversal methods to indicate that a
message is present.
PAUSE TIME ADJUSTMENT
The ‘PAUSE’ key may be congured via
the keypad to represent 1 of 4 time periods
(1~4 sec.). In all cases, lift the handset,
press SET, PAUSE, followed by a numeric
key (1~4) to set the pause time, replace
LCD CONTRAST
Whether mounting the Berkshire 600 AG
on a wall or simply sitting on a desk, it
may be necessary to adjust the display
viewing angle. One of 4 selections can be
programmed;
Press the SET key.
Press one of the 2 navigation keys
directly below the display.
Press the desired numeric key
(1~4).
Typically viewing angles 1-3 are selected
for desktop use, and 4 for wall mount
applications.
Press SET to save the selection.
LCD TIME + DATE ADJUSTMENT
Press the SET key.
Press the CLOCK key and observe
the ashing 24 hour numbers in
the top left position of the display.
Changing this number is done by
direct numeric key entry. Upon entry
of the second character, the cursor
will automatically move to the next
data entry location.
Upon completion of time, date and year
information, press SET to save changes in
the memory.
SWITCHABLE MESSAGE WAITING
There are three versions of message waiting
indicationsupportedwithintheBerkshire600
telephone (MW 3, 8 and 10). This selection
is made via a 4 position switch located to
the rear of the telephone, indicated by the
letters ‘MW’.
A ‘Ring Indicator’ position is provided that
►
►
►
►
[2nd HEADSET].
ACTIVATING OR DEACTIVATING THE
BLUETOOTH®FEATURE:
The ATL Berkshire 600 AG is supplied with
theBluetooth®FunctionON,shouldyouneed
to deactivate the Bluetooth®Functionality
press [SET], [PAIRING], [VOLUME-] and
[SET] to conrm, the LCD will show “0F”
in the right hand top corner to indicate the
OFF status of the Bluetooth®Function. To
activate the Bluetooth®Function, press
[SET], [PAIRING], [VOLUME+] and [SET] to
conrm.
NOTE: WHEN THE AC POWER SUPPLY
IS UNAVAILABLE FOR THE UNIT,
OR THE TELEPHONE IS POWERED
ONLY BY THE TELEPHONE LINE,
THE BLUETOOTH®FEATURE IS
DEACTIVATED AUTOMATICALLY.
RECEIVING CALLS
When your telephone rings, the call can be
answeredbylifting the Handset, pressingthe
HANDSFREE button or pressing the CALL
CONTROL BUTTON on your Bluetooth®
Headset. Additional details on answering
a call on your Bluetooth®Headset can be
found in the User Manual supplied with your
Bluetooth®Headset.
MAKING CALLS
Calls can be made by lifting the Handset,
pressing the HANDSFREE button or
pressing the CALL CONTROL BUTTON
on your Bluetooth®Headset and then
dialling the relevant buttons. In addition
the ATL Berkshire 600 AG allows the
required number to be pre-congured using
the keypad and then dialled by lifting the
Handset, pressing the HANDSFREE button
or pressing the CALL CONTROL BUTTON
on your Bluetooth®Headset.
ADJUSTING THE VOLUME
You can adjust the volume of the Handset
and Handsfree, when “Off-Hook”, by
pressing the (+) and (-) keys located on
the front face of the Berkshire 600 AG and
marked ‘VOLUME’, there are 8 volume
settings available, as indicated by the
display. For Handsfree the selected setting
will be retained for future calls but the
Handset will return to the default setting, i.e.
volume 4.
You can adjust the volume on the Bluetooth®
Headset by pressing the LISTEN VOLUME
ADJUST BUTTONS +/- on your Bluetooth®
Headset, additional details on volume
adjustment of your Bluetooth®headset can
be found in the User Manual supplied with
your Bluetooth®Headset.
TRANSFERRING CALLS
FROMHANDSETTOBLUETOOTH®
HEADSET
If you have taken a call on the
Handsetandwishtotransferittoyour
Headset, press the CALLCONTROL
BUTTONonyourBluetooth®Headset
and replace the Handset. Additional
details on answering a call on your
Bluetooth®headset can be found in
the User Manual supplied with your
Bluetooth®Headset.
FROM HANDSET TO HANDSFREE
If you have taken a call on the
Handset and wish to transfer it to
Handsfree, press the HANDSFREE
Button on the telephone and replace
the Handset.
FROM BLUETOOTH®HEADSET
TO HANDSET
If you have taken a call on your
►
►
►

Bluetooth®Headset and wish to
transfer it to the Handset, simply
pick up the Handset. This action will
switch off the Bluetooth®Headset.
FROM BLUETOOTH®HEADSET
TO HANDSFREE
If you have taken a call on your
Bluetooth®Headset and wish to
transfer it to Handsfree, simply
press the HANDSFREE Button. This
action will switch off the Bluetooth®
Headset.
FROM HANDSFREE TO HANDSET
If you have taken a call in Handsfree
mode and wish to transfer it to
the Handset, simply pick up the
Handset. This action will switch off
the Handsfree mode.
FROM HANDSFREE TO
BLUETOOTH®HEADSET
If you have taken a call on in
Handsfree mode and wish to transfer
it to you Bluetooth®Headset, press
the CALL CONTROL BUTTON
on your Bluetooth®Headset and
replace the Handset. Additional
details on answering a call on your
Bluetooth®headset can be found in
the User Manual supplied with your
Bluetooth®Headset.
►
►
►
Recommended
Bluetooth®
Headsets
For details of the Bluetooth®Headsets
recommended by ATL for use with the ATL
Berkshire 600 AG visit the ATL website at
www.atltelecom.com
Additional
Berkshire 600 AG
Features
TRANSFER KEY (RECALL)
Berkshire 600 AG telephones are provided
with a TRANSFER key, required by modern
public and private exchanges, in order to
gain access to various features such as
‘transferring a call’. For this, the 2 position
selector switch at the rear of the telephone
must be set to the ‘T’ (Time Break Recall) or
‘E’ (Earth Leg Recall) position, to suit your
system requirements.
REDIAL KEY
If you wish to redial the last number you
dialled, you can do so by either just pressing
the REDIAL Button or alternatively by lifting
the handset, and then pressing the REDIAL
button.
MUTE KEY
The microphone in the Handset, Handsfree
and Bluetooth®Headset can be turned off
(mute) in order for you to refer to a colleague
without your caller hearing you.
Pressing the MUTE button turns off the
microphone and gives visual LED indication
within the MUTE button and on the LCD.
Pressing the MUTE button again turns the
microphone back on and the LED indication
within the MUTE button and LCD is turned
off.
Should you wish to turn off (mute) the
microphone when in Bluetooth®Mode, and
away from the telephone, press the Power
/ Mute Button on the Bluetooth®Headset,
additional details on performing the mute
operation on your Bluetooth®headset can
be found in the User Manual supplied with
your Bluetooth®Headset.
MEMORY LOCK
If when pressing the SET key, the display
indicates LOCK IS ON, press both
navigation keys directly below the display
simultaneously. This will turn the memory
lock off, and allow information to be saved.
Pressing the same two keys again will set
the lock back on if desired.
MEMORY KEYS
The Berkshire 600 AG comes with 24 non
volatile (no batteries required) memories,
for efcient speed dialling of commonly
used numbers. Making a call via the rst 12
(upper) memory locations can be performed
by pressing the desired memory key and
then either lifting the Handset, pressing the
HANDSFREE Button or pressing the CALL
CONTROL BUTTON on your Bluetooth
Headset.Theremaining12(lower)memories
are initiated by pressing the ‘SHIFT’ key
prior to the desired memory key. To identify
these keys it will rst be necessary to write
the names of the company or individuals the
keys will represent, on to the label provided.
This label is held in place by a clear plastic
cover, which can be removed by simply
depressing the retaining clips in the lower
corners, and lifting clear.
With the cover replaced, and memory keys
identied, you are now ready to program
them. First check that the memory lock is set
to ‘off’ - refer to previous chapter.
For the 12 (upper) memory locations press
the SET key, or for the 12 (lower) memories
press the SET key, followed by the Shift
Press the memory key to be programmed.
Enter the telephone number to be dialled
followed by the SET key.
If your telephone is on a PABX extension,
it will be necessary to enter the access
digit (9) before the number to be entered.
The PAUSE key is also available to enter a
timed space between the 9 and number, as
required on some PABX systems.
The above instructions have allowed you to
program the rst 12 direct (upper) memories
available. The remaining 12 indirect (lower)
memories are programmed the same way,
but require the ‘SHIFT’ key to be pressed
after the SET key.
i.e. SET, SHIFT, MEM KEY, number, SET.
LIQUID CRYSTAL DISPLAY - LCD
The LCD on the ATL Berkshire 600 AG is
active with the time and date presented at
all times, apart from displaying telephone
numbers, a ‘call timer’ will show the length
of each call automatically from the moment
the handset is picked up.

Bluetooth®Headset and wish to
transfer it to the Handset, simply
pick up the Handset. This action will
switch off the Bluetooth®Headset.
FROM BLUETOOTH®HEADSET
TO HANDSFREE
If you have taken a call on your
Bluetooth®Headset and wish to
transfer it to Handsfree, simply
press the HANDSFREE Button. This
action will switch off the Bluetooth®
Headset.
FROM HANDSFREE TO HANDSET
If you have taken a call in Handsfree
mode and wish to transfer it to
the Handset, simply pick up the
Handset. This action will switch off
the Handsfree mode.
FROM HANDSFREE TO
BLUETOOTH®HEADSET
If you have taken a call on in
Handsfree mode and wish to transfer
it to you Bluetooth®Headset, press
the CALL CONTROL BUTTON
on your Bluetooth®Headset and
replace the Handset. Additional
details on answering a call on your
Bluetooth®headset can be found in
the User Manual supplied with your
Bluetooth®Headset.
►
►
►
Recommended
Bluetooth®
Headsets
For details of the Bluetooth®Headsets
recommended by ATL for use with the ATL
Berkshire 600 AG visit the ATL website at
www.atltelecom.com
Additional
Berkshire 600 AG
Features
TRANSFER KEY (RECALL)
Berkshire 600 AG telephones are provided
with a TRANSFER key, required by modern
public and private exchanges, in order to
gain access to various features such as
‘transferring a call’. For this, the 2 position
selector switch at the rear of the telephone
must be set to the ‘T’ (Time Break Recall) or
‘E’ (Earth Leg Recall) position, to suit your
system requirements.
REDIAL KEY
If you wish to redial the last number you
dialled, you can do so by either just pressing
the REDIAL Button or alternatively by lifting
the handset, and then pressing the REDIAL
button.
MUTE KEY
The microphone in the Handset, Handsfree
and Bluetooth®Headset can be turned off
(mute) in order for you to refer to a colleague
without your caller hearing you.
Pressing the MUTE button turns off the
microphone and gives visual LED indication
within the MUTE button and on the LCD.
Pressing the MUTE button again turns the
microphone back on and the LED indication
within the MUTE button and LCD is turned
off.
Should you wish to turn off (mute) the
microphone when in Bluetooth®Mode, and
away from the telephone, press the Power
/ Mute Button on the Bluetooth®Headset,
additional details on performing the mute
operation on your Bluetooth®headset can
be found in the User Manual supplied with
your Bluetooth®Headset.
MEMORY LOCK
If when pressing the SET key, the display
indicates LOCK IS ON, press both
navigation keys directly below the display
simultaneously. This will turn the memory
lock off, and allow information to be saved.
Pressing the same two keys again will set
the lock back on if desired.
MEMORY KEYS
The Berkshire 600 AG comes with 24 non
volatile (no batteries required) memories,
for efcient speed dialling of commonly
used numbers. Making a call via the rst 12
(upper) memory locations can be performed
by pressing the desired memory key and
then either lifting the Handset, pressing the
HANDSFREE Button or pressing the CALL
CONTROL BUTTON on your Bluetooth
Headset.Theremaining12(lower)memories
are initiated by pressing the ‘SHIFT’ key
prior to the desired memory key. To identify
these keys it will rst be necessary to write
the names of the company or individuals the
keys will represent, on to the label provided.
This label is held in place by a clear plastic
cover, which can be removed by simply
depressing the retaining clips in the lower
corners, and lifting clear.
With the cover replaced, and memory keys
identied, you are now ready to program
them. First check that the memory lock is set
to ‘off’ - refer to previous chapter.
For the 12 (upper) memory locations press
the SET key, or for the 12 (lower) memories
press the SET key, followed by the Shift
Press the memory key to be programmed.
Enter the telephone number to be dialled
followed by the SET key.
If your telephone is on a PABX extension,
it will be necessary to enter the access
digit (9) before the number to be entered.
The PAUSE key is also available to enter a
timed space between the 9 and number, as
required on some PABX systems.
The above instructions have allowed you to
program the rst 12 direct (upper) memories
available. The remaining 12 indirect (lower)
memories are programmed the same way,
but require the ‘SHIFT’ key to be pressed
after the SET key.
i.e. SET, SHIFT, MEM KEY, number, SET.
LIQUID CRYSTAL DISPLAY - LCD
The LCD on the ATL Berkshire 600 AG is
active with the time and date presented at
all times, apart from displaying telephone
numbers, a ‘call timer’ will show the length
of each call automatically from the moment
the handset is picked up.

has the additional benet of being activated
by short ring burst MW signals - see website
for details.
In all cases, an LED in the top right hand
corner of the telephone is used to indicate
the selected functions and incoming calls.
Any questions you may have should be
directed in the rst instance to your telephone
supplier with details of your PABX.
Further concerns may also be addressed
by calling our Technical Support Dept. or
visiting our website, www.atltelecom.com
MODEM PORTS
Your Berkshire 600 AG comes with two
modem ports (BS6312 and RJ11) typically
used for a PC modem, or as points of
connection for additional telephones.
HEARING AID COMPATIBILITY
For hearing aid users, an inductive coupler
has been installed in the handset of the
Berkshire 600 AG, to improve audible
efciency.
Installation Notes
MESSAGE WAITING
MW3 is used by systems that use high
voltage DC signalling. MW8/10 however
use line reversal methods to indicate that a
message is present.
PAUSE TIME ADJUSTMENT
The ‘PAUSE’ key may be congured via
the keypad to represent 1 of 4 time periods
(1~4 sec.). In all cases, lift the handset,
press SET, PAUSE, followed by a numeric
key (1~4) to set the pause time, replace
LCD CONTRAST
Whether mounting the Berkshire 600 AG
on a wall or simply sitting on a desk, it
may be necessary to adjust the display
viewing angle. One of 4 selections can be
programmed;
Press the SET key.
Press one of the 2 navigation keys
directly below the display.
Press the desired numeric key
(1~4).
Typically viewing angles 1-3 are selected
for desktop use, and 4 for wall mount
applications.
Press SET to save the selection.
LCD TIME + DATE ADJUSTMENT
Press the SET key.
Press the CLOCK key and observe
the ashing 24 hour numbers in
the top left position of the display.
Changing this number is done by
direct numeric key entry. Upon entry
of the second character, the cursor
will automatically move to the next
data entry location.
Upon completion of time, date and year
information, press SET to save changes in
the memory.
SWITCHABLE MESSAGE WAITING
There are three versions of message waiting
indicationsupportedwithintheBerkshire600
telephone (MW 3, 8 and 10). This selection
is made via a 4 position switch located to
the rear of the telephone, indicated by the
letters ‘MW’.
A ‘Ring Indicator’ position is provided that
►
►
►
►
[2nd HEADSET].
ACTIVATING OR DEACTIVATING THE
BLUETOOTH®FEATURE:
The ATL Berkshire 600 AG is supplied with
theBluetooth®FunctionON,shouldyouneed
to deactivate the Bluetooth®Functionality
press [SET], [PAIRING], [VOLUME-] and
[SET] to conrm, the LCD will show “0F”
in the right hand top corner to indicate the
OFF status of the Bluetooth®Function. To
activate the Bluetooth®Function, press
[SET], [PAIRING], [VOLUME+] and [SET] to
conrm.
NOTE: WHEN THE AC POWER SUPPLY
IS UNAVAILABLE FOR THE UNIT,
OR THE TELEPHONE IS POWERED
ONLY BY THE TELEPHONE LINE,
THE BLUETOOTH®FEATURE IS
DEACTIVATED AUTOMATICALLY.
RECEIVING CALLS
When your telephone rings, the call can be
answeredbylifting the Handset, pressingthe
HANDSFREE button or pressing the CALL
CONTROL BUTTON on your Bluetooth®
Headset. Additional details on answering
a call on your Bluetooth®Headset can be
found in the User Manual supplied with your
Bluetooth®Headset.
MAKING CALLS
Calls can be made by lifting the Handset,
pressing the HANDSFREE button or
pressing the CALL CONTROL BUTTON
on your Bluetooth®Headset and then
dialling the relevant buttons. In addition
the ATL Berkshire 600 AG allows the
required number to be pre-congured using
the keypad and then dialled by lifting the
Handset, pressing the HANDSFREE button
or pressing the CALL CONTROL BUTTON
on your Bluetooth®Headset.
ADJUSTING THE VOLUME
You can adjust the volume of the Handset
and Handsfree, when “Off-Hook”, by
pressing the (+) and (-) keys located on
the front face of the Berkshire 600 AG and
marked ‘VOLUME’, there are 8 volume
settings available, as indicated by the
display. For Handsfree the selected setting
will be retained for future calls but the
Handset will return to the default setting, i.e.
volume 4.
You can adjust the volume on the Bluetooth®
Headset by pressing the LISTEN VOLUME
ADJUST BUTTONS +/- on your Bluetooth®
Headset, additional details on volume
adjustment of your Bluetooth®headset can
be found in the User Manual supplied with
your Bluetooth®Headset.
TRANSFERRING CALLS
FROMHANDSETTOBLUETOOTH®
HEADSET
If you have taken a call on the
Handsetandwishtotransferittoyour
Headset, press the CALLCONTROL
BUTTONonyourBluetooth®Headset
and replace the Handset. Additional
details on answering a call on your
Bluetooth®headset can be found in
the User Manual supplied with your
Bluetooth®Headset.
FROM HANDSET TO HANDSFREE
If you have taken a call on the
Handset and wish to transfer it to
Handsfree, press the HANDSFREE
Button on the telephone and replace
the Handset.
FROM BLUETOOTH®HEADSET
TO HANDSET
If you have taken a call on your
►
►
►

PAIRING MODE
While the telephone is in the “On-Hook”
mode, Press and hold the [PAIRING] key
for 3 seconds to enter pairing mode, the
telephone will start to search for Bluetooth®
Headsets for 3 minutes, the LCD will show
PAIRING HEADSET, if there is a Bluetooth®
Headset within range and in pairing mode,
the telephone will discover it and display
it’s brand name on the LCD. The LCD will
now prompt you to enter the PIN Code for
the pairing process, the Default PIN Code is
0000, you can enter the correct PIN Code
and press [PAIRING] button to conrm or if
you don’t enter a PIN Code the request for
the code will timeout after 3 seconds. The
pairing procedure will be successful when
the Bluetooth®Headset has the same PIN
code and the telephone will show HEADSET
PAIRED, otherwise the telephone will show
PAIRING FAILED when the pair mode has
timed out.
If you plan to Pair a second Bluetooth®
Headset, repeat this procedure.
Note: If an attempt is made to Pair an addi-
tional Bluetooth®Headset, when two Head-
sets have been previously Paired, the LCD
will display PAIR LIST FULL, you must Clear
Paired Headsets before attempting to Pair a
new Headset.
EXIT PAIRING MODE
While the telephone is in the “On-Hook”
mode, press and hold the [PAIRING] key for
over 3 seconds to enter the Pairing Mode,
and then press [PAIRING] key again this
will cause the telephone to exit the Pairing
Mode, and the telephone will show CANCEL
PAIRING.
CLEAR PAIRED HEADSETS
While the telephone is in the “On-Hook”
mode, press and hold the [PAIRING] key
over 3 seconds to enter Pairing Mode,
and then press and hold [PAIRING] key for
over 3 seconds before the clearing pairing
procedure is successful, this operation
will clear the Paired Headset List, and the
telephone will show PAIRING CLEARED.
CLEAR PAIRED HEADSETS
INDIVIDUALLY
Whilethetelephoneisinthe“On-Hook”mode,
press and hold either the [1st HEADSET] or
[2nd HEADSET] for over 5 seconds, this
will delete this headset from paired list, the
telephone will show HEADSET REMOVED
and then NO HEADSET.
MULTIPLE HEADSETS FUNCTION:
TheATL Berkshire 600AG can support up to
two headsets, this means that the user can
Pair up to a maximum of two headsets and
the ATL Berkshire 600 AG will detect and
attempt to make a connection with one of
the Paired Headsets when the user selects
a working headset.
AUTO HEADSET DETECTION:
ThetelephonecandetectthePairedHeadset
status and prompt its status on the LCD
automatically, when the telephone is in the
“On-Hook” mode, the Bluetooth®Headset
connectingstatus is showas BLUETOOTH®
MODE or CONNECTING.
VIEWING PAIRED HEADSETS:
While the telephone is in the “On-Hook”
mode it’s possible to view which Bluetooth®
Headsets are Paired with the ATL Berkshire
600 AG by simply pressing the [VOLUME-]
key which will list the [1st HEADSET] or by
pressing [VOLUME+] key which will list the
handset. Default = 1s.
TBR TIME ADJUSTMENT
Transfer break times may be adjusted from
100~600ms. in increments of 100ms. First
conrm that the 2 position switch, identied
as RECALL on the rear of the phone, is set
to the ‘T’ position. Lift the handset, press
SET, TRANSFER, followed by a numeric
key (1~6), replace the handset. Default =
100ms.
PROGRAMMING PORT
The Berkshire 600 AG has an unidentied
port, alongside the other conguration
switches, at the rear of the telephone.
Programming of this port is limited to
technicians trained in its use.
Help
If the telephone appears to be faulty when
rst connected, a few simple checks may
help to identify some possible problems, as
listed below:
NO DIAL TONE
Check that the telephone plug is fully
inserted in the socket
If it is, try connecting the telephone
into another socket, if available. If
dial tone is now heard, the original
socket is faulty.
Alternatively, try connecting another
telephone into your socket. If this
telephone gives dial tone, then your
new telephone is probably faulty.
►
►
►
TRANSFER/RECALL KEY NOT WORKING
Change the recall selector switch
setting (T/E). If the transfer operation
is now satisfactory, the problem is
resolved.
Compliance Notes
The Berkshire 600 AG may be connected to
the following types of installation:
Direct Exchange Lines (DEL)
Compatible Private Automatic
Branch
Exchanges (PABX). Please contact
the supplier of your Berkshire 600
AG to conrm compatibility with your
PABX.
Whilst the Berkshire 600 AG is compliant as
an extension to a compatible PABX system,
it cannot be guaranteed to operate under all
possible conditions of connection. Any case
of difculty should be referred in the rst
instance to the supplier of your telephone.
Power Rating
Information – AC
Plug Top Adapter
Input 230V ~ 50 Hz, 50mA
Output 7.5V ~ 50Hz, 300mA
ATL recommends only using the approved
adapter supplied with this product (ATL Part
Number 5/500/100/064)
►
1.
2.

Safety Statement
The Plug Top Power Supply included with
your ATL Berkshire 600 AG serves as the
disconnection device; therefore a socket
outlet shall be installed near the equipment,
and shall be easily accessible. Disconnect
the line cord before attempting to remove
the plug top power supply input jack from
the telephone.
Guarantee
YourBerkshire600 AGtelephoneisdesigned
and manufactured to exacting quality
standards.ThisenablesATL TelecomLimited
to offer a 2 year guarantee from the date of
purchase. This guarantee protects against
faulty material or workmanship, applies to
the UK only and is not transferable.
The terms and conditions under which
the guarantee will be valid are as set out
overleaf.
Misuse or any modication carried
out to the telephone, or operation
other than in accordance with the
instructions supplied, will invalidate
the guarantee.
Damage arising from incorrect
installation, accidental damage or
consequential loss, are not covered
under the guarantee.
In the event of a fault developing
during the period of the guarantee,
the complete telephone should be
returned to your supplier, adequately
and safely packed, together with
proof of date of purchase.
The liability of ATL Telecom Limited
1.
2.
3.
4.
will be limited to the cost of repair or
complete replacement of the same
defectiveinstrument,atthediscretion
of the company. In the event that the
same item is not available, a suitable
alternate will be offered.
The terms of this guarantee do not
affect your statutory rights.
The Bluetooth®word mark and logos are
owned by the Bluetooth SIG, Inc. and any
use of such marks by ATL Telecom is under
licence. Other trademarks and trade names
are those of their respective owners.
ATL BERKSHIRE 600 AG
BLUETOOTH®Core Specication
V1.2
BLUETOOTH® Range up to 10
metres
5.
ADJUSTING YOUR RINGER-VOLUME
Theringervolumeiscontrolledbya3position
switch located at the rear of the telephone,
and indicated by the word ‘ringer’. Moving
through the settings from left to right they
are HIGH, MED and LOW.
ADJUSTING YOUR RINGER PITCH
The ringer pitch control is also a 3 position
switch located at the rear of the telephone,
and indicated by the words ‘RINGER
PITCH’. Settings from left to right are HIGH,
MED and LOW.
MAKING A CALL VIA THE HANDSET
Pick up the handset and listen for
dial tone
Dial the required telephone number
(Note: making external calls from a
company exchange (PABX) requires
the number to be prexed by an access
digit, notmally ‘9’)
Using your
Berkshire 600 AG
with Handsfree
Whether it’s having both hands available,
or conference calling with colleagues, the
speakerphone feature of the Berkshire
600 AG is seen by many as a valuable
benet. Operation is via the HANDSFREE
key, (providing the handset is left in place).
Speaker volume may be adjusted via the [+]
and [-] keys.
►
►
Using your
Berkshire 600 AG
with a Bluetooth®
Headset
BLUETOOTH®FUNCTION
The ATL Berkshire 600 AG can allow a
maximum of two Bluetooth®headsets to be
Paired at any one time and will maintain a
connection to the activated device providing
it’s available, i.e. switched on and within
service range. Once you select a Paired
headset as the working headset, and the
headset is turned on, the telephone can
detect the headset status automatically,
this means that if the headset is turned off,
running out of battery or out of service range
the telephone can detect there’s no headset
available. The telephone will attempt to
reconnect to this headset providing the
user hasn’t selected an alternative headset,
the telephone can detect the headset as
available immediately when its switched on,
or an out of range headset is back within the
telephone service area.
With the ATL Berkshire 600 AG in the “On-
Hook” mode, the [MUTE] key is dened as
the [PAIRING] key, which can activate the
pairing mode, cancel the pairing mode or
clear the paired list.
WhentheATLBerkshire600AGisinthe“On-
Hook” mode, the [VOLUME-] key is dened
as [1st HEADSET] key and [VOLUME+] key
actsasthe[2ndHEADSET] key,youcanuse
these two buttons to select which headset
should be used as the active headset.