Atlantic Furniture RICHLAND BUNK BED TWIN-TWIN User manual

Page 1 of 9
BUNK SAFETY WARNING
Size of Mattress and Foundation
The length and width of the upper and lower bunk mattress and foundation are as follows :
Width
37 ½”- 38 ½”
52”- 53”
LengthSize
74”- 75”
74”- 75”
Twin
Full
Thickness
9 ½” max
9 ½” max
You must use only this size mattress.
Ensure thickness of upper and lower mattress and foundation combined does not exceed 9 ½”
and that the mattress is at least 5” below upper edge of guardrails.
This Bunk Bed uses a slat kit for mattress foundation.
Replacement Parts
Replacement parts, including additional guardrails, may be obtained from any
Atlantic Furniture dealer
SAFETY WARNINGS
! !
( 1 )
( 2 )
( 3 )
( 4 )
( 5 )
( 6 )
( 7 )
( 8 )
( 9 )
(10)
(11)
(12)
(13)
Follow the information on the warnings appearing on the upper bunk end structure
and on the carton. Do not remove warning label from bed.
Always use the recommended size mattresses or mattress support, or both,
to help prevent the likehood of entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other component are
in their proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use ladder for entering or leaving upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and the wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD : Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts
and jump ropes.
Keep these instructions for future reference.

READY
ASSEMBLY INSTRUCTIONS
HARDWARE
Adult Assembly
Allen wrench
Phillips Head
Customer Supplied
Screwdriver
Before assembling your Rich bunk bed, please read through theseland
Thank you for choosing our new bunk bed.
This practical design offers the utmost in versatility.
TWIN - TWIN
instructions carefully. Familiariz yourself with the different parts.e
Please note that you will require a Phillips head screwdriver and an Allen wrench.
RICH BUNK BEDLANDRICH BUNK BEDLAND
BUNK BED SHOWN WITH LADDER
Page 2 of 9
AJCB M6 X 3 ”(80mm) -16 pcs1/8
Spare - 1 pc
B
D
E
F
C
Barrel Nut - pcs16
Allen Screw M6 X 2"(50mm) - 8 pcs
Wood Screw 1" - 1 pc
Wood Screw 5/8" 4- pcs
Allen Screw M6 X 2 3/4”(70mm)- 6 pcs
Spare - 1 pc
Spare - pc1
Spare - pc1
Spare - pc1
Spare - 1 pc
Metal Pins - 4 pcs
E
HAllen wrench - 1 pc
Spare - 1 pc
G
GUARDRAIL CAN BE SET UP AT EITHER
END OF THE BUNK BED
ATTENTION! If you receive a damaged or defective item,
please contact Atlantic Furniture at [email protected] 1-800-955-3726 / M-F 9:00-5:00 EST
NOTE: WE INCLUDE SPARE HARDWARE IN CASE THE ALLEN WRENCH, JCB, BARREL NUTALLEN SCREW,
OR WOOD SCREW ARE DAMAGED DURING ASSEMBLY.

PARTS LIST
01
02
03
04
05
06
07
08
09
10
11
12
HARDWARE
UPPER PANEL
1 BOX
1 BOX
LOWER PANEL
RIGHT SIDE RAIL
LEFT SIDE RAIL
LADDER STEP 1
LADDER STEP 2
END CAP
FULL GUARD RAIL
3/4 GUARD RAIL
LONG RAIL
SLAT KIT TWIN
01
02
09
10
12
12
11
11
11
11
03
04
08
02
03
Page 3 of 9
05
06
06
07
07
06
2 BOX

STEP
STEP
A
A
D
D
A
B
B
B
Attach the long rails (11) to the upper panels (02), using JCB M6 X 3 ” (A) and barrel nut ( ).1/8 B
Tighten with the Allen wrench (H).
Attach the 3/4 guard rail (10) to the end cap (08), using Allen screw M6 X 2 ” (D).
Tighten with the Allen wrench (H).
Adult Assembly
A
B
H
JCB M6 X 3 ”1/8
Barrel Nut
Allen wrench
Page 4 of 9
1
2
A
B
11
10
08
11
02
02
D
Adult Assembly
Allen Screw 2 ”
H
Allen wrench

Adult Assembly
Phillips head
Customer Supplied
screwdriver
Adult Assembly
Phillips head
Customer Supplied
screwdriver
H
E
C
Page 5 of 9
Lay the twin slat kit (12) onto the bed. Fix in place using wood screws provided in the slat kit box.
FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit.
Install the full and 3/4 guard rail assembly (09)(10) to the upper panel, and fix in place using Allen screws(C).
Tighten with the Allen wrench (H). Using wood screw (E) as shown below. Tighten with Phillips head
screwdriver (Customer Supplied).
STEP 3
12
09
STEP 4
GUARDRAIL CAN BE SET UP AT EITHER
END OF THE BUNK BED
C
C
C
C
C
E
C
10
If the bunk bed will be placed next
to a wall, the guard rail that runs
the full length of the bed should be
placed against the wall to prevent
entrapment between the bed and the wall.
Screw hole on end cap
go on inside of guard rail.
FULL GUARD RAIL
3/4 GUARD RAIL
ASSEMBLY
Allen Screw 2 3/4”
Allen wrench

Adult Assembly
A
B
H
JCB M6 X 3 ”1/8
Barrel Nut
Allen wrench
Attach the long rails (11) to the lower panel (03), using JCB M6 X 3 ” (A), and barrel nut ( ).1/8 B
Tighten with the Allen wrench (H).
Adult Assembly
Phillips head
Customer Supplied
screwdriver
Page 6 of 9
STEP 5
STEP 6
12
Lay the twin slat kit (12) onto the bed. Fix in place using wood screws provided in the slat kit box.
FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit.
A
A
A
A
B
B
B
B11
11
03
03

Adult Assembly
Metal Pins
G
Insert metal pins ( ) into the holes in top of the lower panels. Lift the upper panels onto the lowerG
panels as shown, and fit the metal pins into the holes in the bottom of the upper panel legs.
This step requires
two strong people.
This step requires
two strong people.
CAUTION
!
Page 7 of 9
STEP 7
STEP 8
G
D
D
D
D
D
D
G
G
G
Attach the left, right side rail (05)(04) to the ladder step 1&2 (06)(07), using Allen screw M6 X 2” (D).
Tighten with Allen wrench (H).
05
06
06
06
07
07
04
Allen 2Screw "
Adult Assembly
D
H
Allen wrench

UPPER
LOWER
INSIDE VIEW
Page 8 of 9
STEP 9
Congratulations !
Adult Assembly
F
INSIDE VIEW
F
F
F
F
Your Richland bunk bed is now ready for use.
We recommend that you recheck that all screws are tight,
and that all parts are secure before use. Periodically to ensure lasting Safety.

Disassemble upper bunk by removing guard rails. Also remove metal pin from lower bunk.
Disassemble upper bunk by removing upper panel (02) and lower bunk by removing lower panel (03).
Exchange upper panel to the lower panel position and Install hardware tighten with Allen wrench.
UPPER BUNK LOWER BUNK
CONVERSION TO 2 TWIN BEDS.
TWO TWIN BEDS
Page 9 of 9
UPPER BUNK LOWER BUNK
02
03
Metal Pin
Adult Assembly