Atlantis Land I-Storm LAN Router ADSL User manual

1
I-STORM LAN ROUTER ADSL
with 4 Fast Ethernet ports + 1 USB port
Quick Start Guide
A02-RA2+/G2 (February 2004)V1.10

I-Storm LAN Router ADSL
2
For more detailed instructions on configuring and using the I-
Storm Lan Router ADSL, please refer to the online manual.
Before beginning the configuration of the Router you have to
know the parameters of your subscription ADSL.
There are five ways ─PPPoE, PPPoA, RFC1483 routed, IPoA,
RFC1483 Bridge─for the device to have a public IP address and
then to access Internet. You have to check with your ISP about
which way is adopted.
VPI/VCI: Consult the telephone company to get the Virtual Path
Identifier (VPI) and Virtual Channel Identifier (VCI) numbers.
The valid range for the VPI is 0 to 255 and for the VCI is 32 to
65535. The default value VPI is 0 and VCI is 32.
For BT (VPI=0, VCI=38) and for KC ((VPI=1, VCI=50).
NAT: The NAT feature allows multiple-user Internet access for
the cost of a single IP account. If you need to have a public server
or a public network, NAT has to be disabled.
Encapsulation Method: Be sure to use the encapsulation method
(LLC/SNAP or VC MUX) required by your ISP.
Gather the information as illustrated in the following table and
keep it for reference.
PPPoE VPI and VCI
VC-based / LLC-based multiplexing
Username and Password
Service Name
PPPoA VPI and VCI
VC-based / LLC-based multiplexing
Username and Password

I-Storm LAN Router ADSL
3
RFC1483
Bridged
VPI/VCI
VC-based / LLC-based multiplexing
RFC1483
Routed
VPI/VCI
VC-based / LLC-based multiplexing
IP address
Subnet mask
Default Gateway (IP address)
IP address (DNS)
IPoA VPI/VCI
IP address
Subnet mask
Default Gateway (IP address)
IP address (DNS)
1.1 Package contents
Make sure that you have the following items:
• I-Storm Lan Router ADSL
• Network cable (CAT 5)
• Cable USB
• Cable RJ-11 ADSL
• Power Adapter AC-DC (12V, 1A)
• CD-ROM (with manual, software and driver)
• This Quick Start Guide

I-Storm LAN Router ADSL
4
1.2 Cabling
Plug one end of the RJ11 cable into the ADSL port on the rear
panel of the Router and insert the other end into splitter , then
connect to Rj45 ports by an Ethernet cable your PCs or Switch.
Finally connect the Adapter to power inlet and turn the power
switch on. Now the I-Storm LAN Router ADSL will enter a self-
test phase for about ten seconds. After this phase the SYS led will
be flashed to indicate that router is in normal operation. Now you
should see the ADSL led first blinking during alignment and then
steady when connection is on.
1.3 The Front Panel LEDs
Port Information
6 POWER Lit green when power adapter is connected.
7 SYS System status indicators when blinking indicate
system is alive.
8 USB Steady green light indicates a valid ADSL
connection.
9-12 LAN Blinking green light indicates an active WAN
session.

I-Storm LAN Router ADSL
5
13 ADSL When lit, it indicates that the ADSL (Line) port is
connected to the DSLAM and working properly.
1.4 The Rear Ports
Port Meaning
1 Line(RJ11) Connect the supplied RJ-11 cable to this port
when connecting to the ADSL/telephone
network.
2 USB Connect the USB cable to this port when
Upgrading Firmware or connecting to PC
3 Reset Press it (10 sec) to restore the factory default
setting back
4 LAN
(4 connettori RJ-45) Connect a straight or crossover Ethernet
cable to this port when connecting to PCs
or Switch in the network
5 POWER (jack) Connect the supplied power adapter to this
jack
6 POWER Switch Premere per accendere/spegnere il Router

I-Storm LAN Router ADSL
6
1.5 Default Settings
Before you configure this I-Storm Lan Router ADSL , you need
to know the following default settings.
Leaving these settings, configuring the PCs such as DHCP client
(follow the instructions below) and configuring ISP connection
(You have to check with your ISP about which way is adopted)
you can configure the I-Storm Lan Router ADSL quickly. For a
more detailed configuration refer to manual on Installation CD.
Below the I-Storm Lan Router ADSL default settings:
• User Name:admin
• Password:Atlantis
• IP Address (192.168.1.254)
• Subnet Mask (255.255.255.0)
• ISP Protocol =PPPoA con VCMux
• DHCP Server active with IP range from 192.168.1.100 to
192.168.1.199
1.6 IE Configuration
Now open IE, go to Instruments menu, select the Connections
tab and select one of the following options:
• Never use remote connection
• Use remote connection if another network connection
isn’t available
Look the following picture.

I-Storm LAN Router ADSL
7

I-Storm LAN Router ADSL
8
1.7 TCP/IP Configuration
Configuring PC (Windows 95/98/ME)
1. Go to Start / Settings / Control Panel. In the Control
Panel, double-click on Network and choose the
Configuration tab.
2. Select TCP / IP -> NE2000 Compatible, or the name of
any Network Interface Card (NIC) in your PC.
3. Click Properties.

I-Storm LAN Router ADSL
9
4. Select the IP Address tab. In this page, click the Obtain
an IP address automatically radio button.
5. Then select the DNS Configuration tab.
6. Select the Disable DNS radio button and click “OK” to
finish the configuration.

I-Storm LAN Router ADSL
10