Atlas IED TSD-DCPD User manual

Owner’s Manual
TSD-DCPD
1x6 DC Power Distribution
TSD-DCPD
1x6 DC Power Distribution with
Isolation & Filtering

Owner’s Manual
TSD-DCPD
1x6 DC Power Distribution
Description
The AtlasIED TSD-DCPD DC Power Distribution Block is designed to save cost and wiring clutter in
installations where multiple DC power supplies with the same voltage are required. Each unit has
one input and 6 isolation outputs. Each output has additional filtering to negate any AC ripple that
may be present in the DC signal. Each output has a current overdrive protection circuit and a power
indicator. The DC voltage operating range depends on the DC input source. The TSD-DCPD can
operate with incoming DC voltage ranging from 9V - 24VDC. The current output also depends on the
power supply current rating.
The TSD-DCPD is part of a full line of AtlasIED Time Saving Devices. These compact
(1.5" x 4" x 2.75") units are designed to solve some of the common audio system problems in the
easiest and in the most efficient and cost-effective way. All models are made from high quality
components and include removable individual I/O connectors for quick and precise wiring, separate
ground terminals for all I/Os assuring secured connections, and removable level controls that can be
replaced with tamper-proof security covers. The TSDs are highly efficient and meet Energy Star™
standards as one 24V DC power supply (available separately) can power multiple Atlas Time Saving
Devices.
Features
•Power Distribution for Up to 6 TSDs
From a Single PSU
•1 In 6 Out Configuration
•Input Operating Voltage Range 9V - 24VDC
•Current Operating Range 250mA to 5A
•DC Filtering Per Channel
• DC Isolation Per Channel
•Status LED Per Channel
• Cable Management System
• MultipleMountingCongurations
• Separate Ground Connections
• Removable Phoenix Style I/O Connectors
• Meets Energy Star™ Standards
• Compact Chassis Design
Installation
• Government Buildings
• Medical Facilities
• OfceEnvironments
• Churches
• Restaurants
• Schools
• Industrial Facilities
• House of Worship

Owner’s Manual
TSD-DCPD
1x6 DC Power Distribution
Rear Panel Description
TSD Input/Output connections are removable for easy system wiring. The connector has a 3.5mm
pitch between pins.
1. DC Power Input - Each TSD that requires DC power comes with a 2 position connector for
an external 24VDC power supply (sold separately). Because of the TSD’s low power consumption,
asingleexternalpowersupplymaypowermorethanoneTSD.Pleaserefertothespecications
on current requirements in milliamps to match with the appropriate power supply. Note: It is
acceptable to exceed the current requirements of the TSDs but NOT safe to use a power supply
that is below the current requirement of the device.
2. Power LED - Illuminates BLUE when 9-24VDC power is present.
3. Isolated DC Outputs - Connect all system TSD products to these outputs, ensuring the total current
draw of all the connected devices does not exceed the supply current of the TSD power supply
being used. Observe the polarity of the output connectors and the polarity of the TSD devices
beingconnectedaswell.Eachoutputislteredandisolated.
4. Active DC Output LEDs - Illuminate Green indicating there is DC voltage available and ready to use
at the outputs.
5. Cable Management Retainer Points - Each TSD includes two cable retainer straps for securing
the included cable management retainers. Remove one of the rear panel screws, align the
panelholewitharetainerandrmlytightenthescrews.
1
55
5 5
2 4 3

Owner’s Manual
TSD-DCPD
1x6 DC Power Distribution
Cable Management
Knob and Security Cover
All front panel level controls feature a removable knob that can be replaced with an included security
cover. Follow these steps to prevent potentiometer damage or unwanted changes.
1. Knob Installation - Turn the potentiometer shaft fully counter-clockwise. Align the knob indicator
to the lowest setting on the panel and the potentiometer shaft slot. Carefully press the knob onto
the potentiometer shaft. Do not force or damage may occur to the potentiometer.
2. Security Cover Installation - Remove the knob from the panel and insert the cover. Small pliers may
be required to remove the knobs. Align the security cover to the level control panel hole. Push the
cover into the hole until it snaps into place. Do not force or damage may occur to the potentiometer.

Owner’s Manual
TSD-DCPD
1x6 DC Power Distribution
Mounting
Listed below are the ways to mount the TSD and the optional accessories that can be purchased.
1. Velcro™- Each unit includes two 2" x 2" pieces of industrial-grade Velcro™with adhesive backing
toadheretoanyatsurface.CleanallsurfacesbeforeapplyingtheadhesivesideoftheVelcro™.
2. Multi Mount Plate - Each TSD includes a versatile multi-position mounting plate. This plate
allows the TSD to be mounted to any surface; but is ideal for use with rear rack rails or side rack
hat channels. Use the included M3 x 4mm screws to install the plate on the TSD. Note: Only use
the included M3 x 4mm screws as other screws may be too long and will cause internal damage
to the TSD. The multi-position mounting plate is a new addition being included with TSDs. If the
TSD being used did not include the mounting plate, contact AtlasIED customer service at
1-800-876-3333.
(M3 x 4mm)
(M3 x 4mm)

Owner’s Manual
TSD-DCPD
1x6 DC Power Distribution
Optional Mounting Accessories
1. TSD-RMK 19" Width Rack Mount Kit - For 19" rack mounting, AtlasIED offers an optional rack
mount kit, the TSD-RMK. This rack mount kit can support up to four TSD units. The kit includes
threeblankpanelsdesignedtollanyunusedslots.UsetheincludedhardwaretomounttheTSD
into the rack mount kit using the top mount screw holes on the TSD.
2. TSD-RMKHR Half Width Rack Mount Kit - AtlasIED offers an optional rack mount kit that can
be used in half width rack applications including the AtlasIED WMA-HR and AWR-HR models.
TheTSD-RMKHRcansupportuptotwoTSDs.Includedisanextrablankpaneltolloneofthe
spaces if only one TSD is being used.

Owner’s Manual
TSD-DCPD
1x6 DC Power Distribution
3. TSD-RRMKRearRackMountingKit-ForcompleteexibilityinmountingaTSDorTSDexternal
power supplies the optional TSD-RRMK is available. The TSD-RRMK can support mounting of
either two larger TSDs with external power supplies or up to 4 TSD models. Note: Only use the
included M3 x 4mm screws as other screws may be too long and will cause internal damage to
the TSD.

Owner’s Manual
TSD-DCPD
1x6 DC Power Distribution
Block Diagram
9~24V
DC IN
1 DC OUT
NOTE: OUTPUT VOLTAGE AND CURRENT IS
DETERMINED BY THE INPUT DC SUPPLY VOLTAGE
D C
DC
D C
D C
D C
D C
2 DC OUT
3 DC OUT
4 DC OUT
5 DC OUT
6 DC OUT

Owner’s Manual
TSD-DCPD
1x6 DC Power Distribution
Specications
Description 1x6 Power Distribution Block with Isolation & Filtering
Chassis Color Black
Chassis Material Aluminum
Inputs
DC Voltage Input 9V - 24V DC, 5A Max
Connection Removable 2 Position Captive Screw 3.5mm Spacing
Outputs
DC Voltage Output Fixed 9V - 24V DC, Voltage and Current Related to Input Power Supply
Connection Qty 6, Removable 2 Position Captive Screw 3.5mm Spacing
Indicators
Power Blue
Active DC Output Green, Qty 6
Electrical
Isolation Active
Filters DC Storage & AC Ripple
Power Requirements
Idle 10mA
Dimensions H 1.5" (39mm) x W 4" (101mm) x D 2.75" (70mm)
Weight 6oz, .165kg
Included Accessories
Velcro™ Industrial-Grade
Multi-Mount Plate Qty 1, Includes Two (2) M3 x 4mm Screws
Cable Retainers Qty 2
Optional Accessories
TSD 24VDC Power Supply
TSD-RMK 1 RU 19" Width Rack Mount Panel (Supports 4 TSD Units)
TSD-RMKHR 1 RU Half Rack Width Panel (Supports 2 TSD Units)
TSD-RRMK Rear Rack Mounting Kit