Atlas RIV939P User manual

RIVP
HYDROPNEUMATIC TOOL
FOR RIVET NUTS FROM M TO M
WITH OIL PRESSURE ADJUSTMENT
OPERATING INSTRUCTIONS
QUALITY MANAGEMENT SYSTEM
CONFORMING TO
ISO 9001:2015 STANDARD
CODE
4843900

2 PennEngineering • www.pemnet.com
Instruction Manual - RIV939P

PennEngineering • www.pemnet.com 3
Instruction Manual - RIV939P
WARNING!
RIV939P COMES WITHOUT KITS.
KITS MUST BE ORDERED SEPARATELY ACCORDING TO USER NEEDS.
FEATURES
RIV939P FEATURES A VALVE-CONTROLLED MOTOR THAT ALLOWS GREATER EFFICIENCY IN SCREWING AND UNSCREWING
(6 BARS = SPEED 2250 rpm).
1. Air piston return (without spring).
2. Power piston air outwardly, not through the piston.
3. Kit assembly with toothed ring nut (wrench is not necessary).
4. Tie rods are now replaced by commercial screws.
5. Additional unscrewing in case the user unintentionally uses an unsuitable insert, or in case it gets stuck due to an improper
regulation.
6. One position trigger mechanism.
7. No adjustments are needed when there is a thickness change in materials.
8. No damages occur to mandrel (or tie rod) if operations are repeated.
9. Lightweight.
10. Small dimensions.
11. Handiness.

4 PennEngineering • www.pemnet.com
Instruction Manual - RIV939P
ITEMS AVAILABLE ON REQUEST
RIV938P, RIV938, RIV939, RIV939P,
RIV939PMAX, RIV941
COMES WITH A SMOOTH BOTTOM (REF. A)
YOU CAN ORDER SEPARATELY THE BOTTOM +
THE MALE EYEBOLT (KIT REF. (B), CODE 4540500)
+ THE BALANCER KG. 2/3 (CODE 0523200)
MOTOR RUBBER PROTECTION COVER (CODE 4796200)
(A)
(B)
48

PennEngineering • www.pemnet.com 5
Instruction Manual - RIV939P
RIV938, RIV938P, RIV939, RIV939P, RIV939PMAX, RIV941
COMES WITHOUT THE ADJUSTABLE AIR SWITCH, WHICH IS
AVAILABLE ON REQUEST (CODE 4280600)
Cod. 4280600
REF. CODE QTY DESCRIPTION
Fig. 2.5 - A 4280600 1 COMPLETE ADJUSTABLE AIR SWITCH KIT
1. 4280700 1 FILTER
2. 4280900 1 BLOCK
3. 3542800 1 SEAL WASHER
4. 4281100 1 SPECIAL HEXAGONAL HEAD SCREW
KIT 37 DEFLECTOR IS FITTED AS STANDARD ON THE TOOL.
IF NEEDED, AND AIR ADJUSTABLE SPECIAL SWITCH IS AVAILABLE ON REQUEST (CODE 4280600).
1 2 3 4

Instruction Manual - RIV939P
CONTENTS
1 - GENERAL INFORMATION P.7
1.1 MANUFACTURER
1.2 ASSISTANCE
1.3 CERTIFICATION AND EC MARKING
1.4 WARRANTY
1.5 MANUAL STRUCTURE
1.5.1 PURPOSE AND CONTENTS
1.5.2 RECEIVERS
1.5.3 PLACING OF THE MANUAL
1.5.4 SYMBOLS USED
2 - TOOL DESCRIPTION P.8
2.1 OPERATING SYSTEM
2.2 VIBRATION
2.3 NOISE LEVEL
2.4 TECHNICAL DATA
2.5 NOSE ASSEMBLIES AND STANDARD ACCESSORIES
2.5.1 ACCESSORIES ON REQUEST
2.5.1.1 FOR RIVSERT PLACING
2.5.1.1.1 KIT939P/03 – KIT FOR RIVSERT M3
2.5.1.1.1.1 KIT939P/03 COMPOSITION
2.5.1.1.2 KIT939P/04 KIT FOR RIVSERT M4
2.5.1.1.2.1 KIT939P/04 COMPOSITION
2.5.1.1.3 KIT939P/05 – KIT FOR RIVSERT M5
2.5.1.1.3.1 KIT939P/05 COMPOSITION
2.5.1.1.4 KIT939P/06 – KIT FOR RIVSERT M6
2.5.1.1.4.1 KIT939P/06 COMPOSITION
2.5.1.1.5 KIT939P/08 – KIT FOR RIVSERT M8
2.5.1.1.5.1 KIT939P/08 COMPOSITION
2.5.1.1.6 KIT939P/10 – KIT FOR RIVSERT M10
2.5.1.1.6.1 KIT939P/10 COMPOSITION
2.5.1.1.7 KIT939P/12 – KIT FOR RIVSERT M12
2.5.1.1.7.1 KIT939P/12 COMPOSITION
2.5.1.1.8 KIT939P/1/2-13UNC - AMERICAN UNC (INCHES) FLAT
HEAD WITH BUSH
2.5.1.1.8.1 KIT939P/1/2-13UNC COMPOSITION
2.5.1.2 FOR RIVBOLT PLACING
2.5.1.2.1 KIT939P/04B – KIT FOR RIVBOLT M4
2.5.1.2.1.1 KIT939P/04B COMPOSITION
2.5.1.2.2 KIT939P/05B KIT FOR RIVBOLT M5
2.5.1.2.2.1 KIT939P/05B COMPOSITION
2.5.1.2.3 KIT939P/06B – KIT FOR RIVBOLT M6
2.5.1.2.3.1 KIT939P/06B COMPOSITION
2.5.1.2.4 KIT939P/08B – KIT FOR RIVBOLT M8
2.5.1.2.4.1 KIT939P/08B COMPOSITION
2.5.1.2.5 KIT939P/10B – KIT FOR RIVBOLT M10
2.5.1.2.5.1 KIT939P/10B COMPOSITION
2.5.1.3 HEAD EXTENSIONS
3 - SPARE PARTS P. 27
3.1 SPARE PARTS
3.1.1 QUICK KIT COMPLETE WITH SPRING
3.1.1.1 QUICK KIT COMPLETE WITH SPRING COMPOSITION
3.1.1.1.1 SPECIAL TOOTHED RING NUT FOR SOCKET CAP SCREW M8 NO
NEED FOR REDUCTION (CODE 3472600) (OPTIONAL)
3.1.2 HIGH RESISTANCE SPECIAL KIT FOR M8 WITH FIXED RING NUT
3.2 SPARE PARTS OF THE MOTOR UNIT (KIT 20)
3.2.1 COMPLETE MOTOR KIT CONSISTING OF 5 ITEMS (CODE 4316600).
3.3 ORDERING SPARE PARTS
4 - SAFETY P. 31
4.1 GENERAL WARNINGS
4.2 INTENDED USE
4.3 OPERATING CONDITIONS
4.4 RESIDUE RISKS
4.5 IDENTIFICATION/SERIAL NUMBER
5 - INSTALLATION P. 33
5.1 TRANSPORT AND HANDLING
5.2 STORAGE
5.3 CONNECTIONS
5.3.1 PNEUMATIC
5.4 AIR SUPPLY
5.5 PRELIMINARY CHECKS
6 - OPERATION P. 34
6.1 OPERATORS
6.2 REPLACEMENT OF STANDARD KIT WITH HIGH RESISTANCE SPECIAL ONE,
FOR M8 ONLY (CODE 4508800) WITH FIXED RING NUT REPLACE TOOTHED
RING NUT (1) WITH THE FIXED ONE (2) + (3) (SEE PARA 3.1.2)
6.3 TOOL PREPARATION AND SCREW REPLACEMENT
6.4 INFORMATION
7 - SERVICING THE TOOL P. 40
7.1 MAINTENANCE STATUS
7.2 CLEANING
7.3 ORDINARY MAINTENANCE
7.3.1 FILLING THE HYDRAULIC CIRCUIT WITH OIL
7.3.2 PARTS SUBJECT TO WEAR
7.4 MAINTENANCE KIT ON REQUEST
8 - FAULT DIAGNOSIS P. 43
8.1 POSSIBLE FAULTS
9 - FAULT DIAGNOSIS AND REPAIRS P. 45
9.1 REPAIRS
9.2 REQUESTING ASSISTANCE
10 - DISMANTLING INSTRUCTIONS P. 45
10.1 DISMANTLING INSTRUCTIONS
11 - ENCLOSED DOCUMENTS P. 45
11.1 DECLARATION

PennEngineering • www.pemnet.com 7
Instruction Manual - RIV939P
1 - GENERAL INFORMATION
1.1 - MANUFACTURER
Established in 1973, Rivit S.r.l. produces and distributes Fasteners and Tools (tools for rivets and rivet nuts). With extensive technical
experience, the company oers a wide range of products for fastening systems.
PHONE ++39 051 4171111 FAX ++39 051 4171129
1.2 - ASSISTANCE
For assistance with tool use or maintenance, or to order spare parts, please contact your local authorized dealer or Rivit S.r.l. directly.
Please specify the identification/serial numbers of the tool, which are written on the outer casing.
C 1 See section 3
1.3 - CERTIFICATION AND EC MARKING
The tool is manufactured in compliance with the European Directives, which are validated when the tool is put on the market. As the
tool is not included in ENCLOSURE IV of DIRECTIVE 2006/42/EC, Rivit S.r.l. issues a self-certification to apply the EC marking.
1.4 - WARRANTY
The warranty is valid for 12 months, as of the date indicated on the invoice.
Warranty covers replaced parts. Labor is not included.
The following are not covered by warranty: Standard accessories (see section 2.5) and tool damages caused by:
• Transport and/or handling.
• User error.
• Failed servicing/maintenance, as indicated in section 7 of this manual.
• Faults and/or breakages not attributable to tool anomalies.
• Normal consumption of consumables.
The warranty is deemed invalid in both the case of unauthorized tampering/replacements of tool components, and in the case of
using accessories, tools or consumables dierent than those recommended by the manufacturer, which could cause potential
injuries to the end user.
Rivit S.r.l. assumes responsibility if the tool is originally defective but is not responsible if the user fails to follow the provided
instructions.
1.5 - MANUAL STRUCTURE
This instruction manual must be read by the Customer to ensure the correct pre-arrangement, installation, and use of tool.
1.5.1 - PURPOSE AND CONTENTS
This manual was developed to provide the Customer with the necessary information to not only to use the tool
correctly, but to also to manage it self-suiciently and safely. It includes information concerning technical aspects,
operation, maintenance, spare parts, and safety.
Users and Qualified Technicians must read the instructions thoroughly before using the tool.
If you have any questions, please contact Rivit S.r.l. for clarification.
1.5.2 - RECEIVERS
This manual has been written for both the operators and the technicians who will service the tool.
Operators should not carry out procedures reserved to service and/or qualified technicians.
Rivit S.r.l. is not liable for any damage caused by failure to observe this rule.
1.5.3 - PLACING OF THE MANUAL
This instruction manual must be kept near the tool, inside a dedicated container, and away from liquids or
anything else that may damage its readability.

8 PennEngineering • www.pemnet.com
Instruction Manual - RIV939P
1.5.4 - SYMBOLS USED
2 - TOOL DESCRIPTION
2.1 - OPERATING SYSTEM
The hydropneumatic RIV939P tool, with oil pressure adjustment, is designed to place the following fasteners:
▶ RIVSERT female rivet nuts (from M3 to M12)
▶ RIVBOLT male rivet nuts (from M4 to M10)
The hydropneumatic system and the mechanical components used inside the structure of the RIV939P, when compared with other
riveting tools, results in greater reliability. Tool features reduce potential issues caused by the wear and tear of the components,
and consequently the tool will last longer and perform better. The technical solutions adopted make the RIV939P more compact and
lighter. The successful outcome is a very handy tool.
2.2 - VIBRATION
When used correctly and in compliance with the instructions given, the tool does not produce dangerous vibration.
2.3 - NOISE LEVEL
The tool is designed and manufactured to generate a very low noise level. The weighed equivalent of continuous acoustic pressure
level A in the operator position is below 80 dB (A).
2.4 - TECHNICAL DATA
The following table provides the technical data and features of the tool. Please refer to this table when contacting our Technical
Assistance Department.
SYMBOL MEANING COMMENT
P ... HAZARD This highlights a hazard with risk for the user.
A ... WARNING This points out a warning/note on key functions or useful information.
Read the texts indicated by this symbol with careful attention.
C ... CONSULT Consult the instruction manual before carrying out a specific
procedure.

PennEngineering • www.pemnet.com 9
Instruction Manual - RIV939P
Figure 2.4-B
Figure 2.4-C
TABLE 2.4-A TECHNICAL DATA AND FEATURES
AIR WORKING PRESSURE 6 bar
MIN – MAX AIR PRESSURE 5 – 7 bar
AIR CONSUMPTION PER CYCLE AT 6 BAR 5 litri
MAX STROKE 6,5 mm
MAX FORCE 26.600 N
MOTOR SPEED (SCREWING)
MOTOR SPEED (UNSCREWING CYCL)
DIRECT UNSCREWING SPEED
2250 rpm a 6,5 bar
2250 rpm a 6,5 bar
2250 rpm a 6,5 bar
WEIGHT (WITHOUT KIT) 2,200 Kg
VIBRATIONS < 2,5 m/s2
NOISE LEVEL 76 dB (A)
REF. CODE QTY DESCRIPTION
Fig. 2.4-C 3531800 1 KIT939P-SPECIAL EXTENDED HEAD
A/1. 3446600 1 90 MM EXTENDED SLEEVE
A/2. 3446900 1 90 MM INTERNAL EXTENDED SLEEVE
When ordering these two items, you can reach a total head extension of 165 mm (see figure 2.4-C)
A/1 A/2

10 PennEngineering • www.pemnet.com
Instruction Manual - RIV939P
2.5 - NOSE ASSEMBLIES AND STANDARD ACCESSORIES
The nose assemblies stated below refer to standard tools.
A special tool may require special parts, dierent to those listed.
Figure 2.5-A
REF. CODE QTY DESCRIPTION
RIV939P- HYDROPNEUMATIC TOOL
FOR RIVET NUTS WITH OIL PRESSURE
ADJUSTMENT (FORCE)
Fig.2.5-A 4843900 1 RIV939P-HYDROPNEUMATIC TOOL
FOR RIVET NUTS (IN CASE)
50. 3064400 1 HYDRAULIC OIL TYPE ISO VG 32
100CC
51. 0369800 1 PLASTIC CASE
52. 0207300 1 UNIVERSAL KEY
53. 2533800 1 EMERGENCY AND STROKE
REGULATION PIN
54. 4154200 1 REGULATION WRENCH MM. 3,0
- - 1 INSTRUCTION MANUAL
53 50 51
52
54
Hook for Balancer (Code 4229800).

PennEngineering • www.pemnet.com 11
Instruction Manual - RIV939P
2.5.1 - ACCESSORIES ON REQUEST
The tool can be supplied with dierent accessories according to the kind of fastener to be placed.
2.5.1.1 - FOR RIVSERT PLACING:
The user must purchase the following kits separately according to the fastener to be used.
KIT CODE
939P/03 3441100
939P/04 3441200
939P/05 3441300
939P/06 3441400
939P/08 3441500
939P/10 3441600
939P/12 3441700
939P/1/2-13 UNC 4361600
You must screw the
dierent kits in this
position
Head RING NUT can be ordered separately (Rivit code 0327700).
COMPLETE SPECIAL HEAD Ø 20,0, M8 (Rivit Code 4281000).
Upon request, we can supply the head in dierent diameters and holes according to your needs.
A1
A2
Ø 8,0
Ø 20,0

12 PennEngineering • www.pemnet.com
Instruction Manual - RIV939P
2.5.1.1.1 KIT939P/03 – KIT FOR RIVSERT M3
Figure 2.5-B
2.5.1.1.1.1 KIT939P/03 COMPOSITION
Figure 2.5-C
TABLE 2.5-A
Upon request, we can provide a screw longer than the standard one.
REF. CODE QTY DESCRIPTION
Fig. 2.5-B 3441100 1 KIT939P-KIT RIVSERT M3 SOCKET CAP SCREW
REF. CODE QTY DESCRIPTION
1. 3457500 1 HEAD WITH RING NUT FOR M3 SCREW
2. 3457400 1 ADAPTER FOR M3 SCREW
3. 3457600 1 SOCKET CAP SCREW M3X4012.9 UNI5931/DIN912
4. 3466200 1 HEXAGONAL JOINT WITH SPRING FOR M3 SCREW
1 2 3 4
REF. CODE QTY DESCRIPTION
3a. 2193500 1 SOCKET CAP SCREW M3X50 12.9 UNI5931/DIN912

PennEngineering • www.pemnet.com 13
Instruction Manual - RIV939P
2.5.1.1.2 KIT939P/04 – KIT FOR RIVSERT M4
Figure 2.5-D
2.5.1.1.2.1 KIT939P/04 COMPOSITION
Figure 2.5-E
TABLE 2.5-B
Upon request, we can provide a screw longer than the standard one.
REF. CODE QTY DESCRIPTION
3a. 4186400 1 SOCKET CAP SCREW M4X65 12.9 UNI5931/DIN912
REF. CODE QTY DESCRIPTION
Fig. 2.5-D 3441200 1 KIT939P-KIT RIVSERT M4 SOCKET CAP SCREW
REF. CODE QTY DESCRIPTION
1. 3470200 1 HEAD WITH RING NUT FOR M4 SCREW
2. 3466300 1 ADAPTER FOR M4 SCREW
3. 3470500 1 SOCKET CAP SCREW M4X5512.9 UNI5931/DIN912
4. 3470600 1 HEXAGONAL JOINT WITH SPRING FOR M4 SCREW
123 4

14 PennEngineering • www.pemnet.com
Instruction Manual - RIV939P
2.5.1.1.3 KIT939P/05 –KIT FOR RIVSERT M5
Figure 2.5-F
2.5.1.1.3.1 KIT939P/05 COMPOSITION
Figure 2.5-G
TABLE 2.5-C
Upon request, we can provide a screw longer than the standard one.
REF. CODE QTY DESCRIPTION
3a. 4285500 1 SOCKET CAP SCREW M5X 65 12.9 UNI5931/DIN912
REF. CODE QTY DESCRIPTION
Fig. 2.5-F 3441300 1 KIT939P-KIT RIVSERT M5 SOCKET CAP SCREW
REF. CODE QTY DESCRIPTION
1. 3471800 1 HEAD WITH RING NUT FOR M5 SCREW
2. 3471700 1 ADAPTER FOR M5 SCREW
3. 3471900 1 SOCKET CAP SCREW M5X5512.9 UNI5931/DIN912
4. 3472000 1 HEXAGONAL JOINT FOR M5 SCREW
12 3 4

PennEngineering • www.pemnet.com 15
Instruction Manual - RIV939P
2.5.1.1.4 KIT939P/06 – KIT FOR RIVSERT M6
Figure 2.5-H
2.5.1.1.4.1 KIT939P/06 COMPOSITION
Figure 2.5-I
TABLE 2.5 - D
Upon request, we can provide a screw longer than the standard one.
REF. CODE QTY DESCRIPTION
3a. 4285300 1 SOCKET CAP SCREW M6X65 12.9 UNI5931/DIN912
REF. CODE QTY DESCRIPTION
Fig. 2.5-H 3441400 1 KIT939P-KIT RIVSERT M6 SOCKET CAP SCREW
REF. CODE QTY DESCRIPTION
1. 3472200 1 HEAD WITH RING NUT FOR M6 SCREW
2. 3472100 1 ADAPTER FOR M6 SCREW
3. 3472300 1 SOCKET CAP SCREW M6X5512.9 UNI5931/DIN912
4. 3472500 1 HEXAGONAL JOINT FOR M6 SCREW
12 3 4

16 PennEngineering • www.pemnet.com
Instruction Manual - RIV939P
2.5.1.1.5 KIT939P/08 – KIT FOR RIVSERT M8
Figure 2.5-J
2.5.1.1.4.1 KIT939P/08 COMPOSITION
Figure 2.5-K
TABLE 2.5-E
Upon request, we can provide a screw longer than the standard one.
REF. CODE QTY DESCRIPTION
3a. 2192800 1 SOCKET CAP SCREW M8X65 12.9 UNI5931/DIN912
REF. CODE QTY DESCRIPTION
Fig. 2.5-J 3441500 1 KIT939P-KIT RIVSERT M8 SOCKET CAP SCREW
REF. CODE QTY DESCRIPTION
1. 3472700 1 HEAD WITH RING NUT FOR M8 SCREW
2. 3472600 1 ADAPTER FOR M8 SCREW
3. 3472800 1 SOCKET CAP SCREW M8X6012.9 UNI5931/DIN912
4. 3472900 1 HEXAGONAL JOINT FOR M8 SCREW
12 3 4

PennEngineering • www.pemnet.com 17
Instruction Manual - RIV939P
2.5.1.1.6 KIT939P/10 – KIT FOR RIVSERT M10
Figure 2.5-N
2.5.1.1.6.1 KIT939P/10 COMPOSITION
Figure 2.5-O
TABLE 2.5-G
Upon request, we can provide a screw longer than the standard one.
REF. CODE QTY DESCRIPTION
2a. 2428500 1 SOCKET CAP SCREW M10X70 12.9 UNI5931/DIN912
2b. 4180100 1 SOCKET CAP SCREW M10X1,25X60 12.9 UNI5931/DIN912
REF. CODE QTY DESCRIPTION
Fig. 2.5-N 3441600 1 KIT939P-KIT RIVSERT M10 SOCKET CAP SCREW
REF. CODE QTY DESCRIPTION
1. 0329000 1 HEAD WITH RING NUT FOR M10 SCREW
2. 3473100 1 SOCKET CAP SCREW M10X6012.9 UNI5931/DIN912
3. 3441800 1 HEXAGONAL JOINT FOR M10 SCREW
12 3

18 PennEngineering • www.pemnet.com
Instruction Manual - RIV939P
2.5.1.1.7 KIT939P/12 – KIT FOR RIVSERT M12
Figure 2.5-P
2.5.1.1.7.1 KIT939P/12 COMPOSITION
Figure 2.5-Q
TABLE 2.5-H
Socket cap screw (commercial allen key to be shaped; please refer to figure 2.5-Q).
REF. CODE QTY DESCRIPTION
Fig. 2.5-P 3441700 1 KIT939P-KIT RIVSERT M12 SPECIAL SOCKET CAP SCREW
REF. CODE QTY DESCRIPTION
1. 0329100 1 HEAD WITH RING NUT FOR M12 SCREW
2. 4316200 1 TOOTHED BLOCKING RING NUT
3. 3473300 1 M12X60 SOCKET CAP SCREW 12.9 (NOT STANDARD)
4. 3473400 1 HEXAGONAL JOINT FOR M12 SCREW
123 4

PennEngineering • www.pemnet.com 19
Instruction Manual - RIV939P
2.5.1.1.8 KIT939P/1/2-13UNC – AMERICAN UNC (INCHES) FLAT HEAD WITH BUSH
Figure 2.5-R
2.5.1.1.8.1 KIT939P/1/2-13UNC COMPOSITION
Figure 2.5-S
TABLE 2.5-I
REF. CODE QTY DESCRIPTION
Fig. 2.5 - R 4361600 1 KIT939P/1/2-13UNC-AMERICAN UNC (INCHES) FLAT HEAD WITH BUSH
REF. CODE QTY DESCRIPTION
1. 4378400 1 M8X6 SOCKET CAP SCREW NUT 4MM ALLEN KEY
2. 4378500 1 M8 - 1/2-13 UNC DOUBLE THREAD BUSH
3. 4378600 1 HEAD (HOLE Ø 8.1)
4. 3472600 1 ADAPTER (HOLE Ø 8.1)
5. 4187000 1 M8X70 SOCKET HEAD CAP SCREW 8.8, UNI 5931
6. 3472900 1 HEXAGONAL JOINT FOR M8 SCREW
1 2 3 4 5 6
KIT ASSEMBLY:
1 - Loosen the M8 nut (1).
2 - Unscrew the bush (2).
3 - Insert the screw (5) inside the ring nut supplied with the tool (Rivit code 4172400).
4 - Make sure the nut (1) is tightly screwed.
A3

20 PennEngineering • www.pemnet.com
Instruction Manual - RIV939P
2.5.1.2 - FOR RIVBOLT PLACING
To install this kit, first remove the quick-kit with spring
The user must purchase the following kits separately according to the fastener to be used.
The tool can have dierent kinds of head assemblies
Head RING NUT can be ordered separately (Code 0327700).
A4
KIT CODE
939P/04B 3442300
939P/05B 3442400
939P/06B 3442500
939P/08B 3422600
You must screw the
dierent kits in this
position
939P/10B 4601900