Atlona AT-UHD-SW-510W User manual

1
Installation Guide
AT-UHD-SW-510W
4K/UHD Five-Input Universal Switcher with Wireless
Presentation Link
AT-UHD-SW-510W
The Atlona AT-UHD-SW-510W is a 5×1 multi-format switcher with wireless presentation
capability. It provides universal BYOD (bring your own device) compatibility with HDMI,
DisplayPort, and USB-C inputs, plus wireless connectivity for mobile devices. The SW-510W
is HDCP 2.2 compliant, and features an HDMI output and a mirrored HDBaseT™ output that
can be used with the Atlona AT-UHD-EX-100CE-RX-PSE HDBaseT receiver. It also includes
automatic input switching and automatic display control capability, both applicable to wired and
wireless source connections. Additionally, the SW-510W can be integrated with an occupancy
sensor to automatically power up the unit and display. This unique multi-format switcher and
wireless gateway provides a universal connectivity solution for presentation devices in a wide
range of professional AV applications.
IMPORTANT: Visit http://www.atlona.com/product/AT-UHD-SW-510W for the latest
rmware updates and User Manual.
1 x AT-UHD-SW-510W
1 x Captive screw connector, 5-pin
1 x Captive screw connector, 4-pin
2 x Captive screw connector, 3-pin
2 x Wi-Fi antennae
1 x 19V DC power supply
1 x Long rack ear
2 x Short rack ear
2 x Mounting plates
4 x Mounting screws
1 x Installation Guide
Package Contents

2
Installation Guide
AT-UHD-SW-510W
1 Input Indicators
Displays the currently selected input.
2 INPUT
Press this button to cycle through each
input.
3 Cursor Buttons
Adjust the volume on the display.
4 DISPLAY
Press this button to toggle the power state
of the desired display.
5 AUDIO IN
Connect a 3.5 mm mini-stereo cable from
an analog audio source to this connector.
6 AUDIO OUT
Use the included captive screw connector
to connect a balanced audio device.
7 USB
Connect the included Wi-Fi antennae to
these ports. These ports also support
Miracast™, Google Cast™, and Apple
AirPlay®.
8 RELAY
Connect one of the included 3-pin captive
screw connectors to this port to control
screens, drapes, lights, or other devices.
9 TRIGGER I/O
Connect voltage-controlled device, such
as an occupancy sensor, to this port.
A 4-pin captive screw connector is
required.
10 RS-232
Use the included captive screw connector
to connect an RS-232 controller or
automation system.
11 USB-C
Connect a USB-C cable from this port to
a USB-C source.
12 DP IN
Connect a DisplayPort device to this port.
13 HDMI IN
Connect an HDMI cable from each of
these ports to an HD/UHD source.
14 HDMI OUT
Connect an HDMI cable from this port
to an HD/UHD display.
15 HDBaseT OUT
Connect to a locally powered HDBaseT
receiver such as the AT-UHD-EX-100CE-
RX-PSE.
16 LAN
Connect an Ethernet cable from this port
to the network.
17 DC 19V
Connect the included power supply to
this port using the included 2-pin captive
screw connector.
Panel Descriptions
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
LAN DC 19V
HDBaseT OUT
HDMI OUTHDMI IN
DP IN
USB-C IN
2 3 4
1
RELAY RS-232
TRIGGER I/O
WiFiWiFi AUX
AUDIO
OUT
L R
IN
USB
+
+
C1 COM C2 RX
PTX
+
+
USB
USB
USB
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
LAN DC 19V
HDBaseT OUT
HDMI OUTHDMI IN
DP IN
USB-C IN
2 3 4
1
RELAY RS-232
TRIGGER I/O
WiFiWiFi AUX
AUDIO
OUT
L R
IN
USB
+
+
C1 COM C2 RX
PTX
+
+
USB
USB
USB
21 3 4
5 6 7 8 9 10
11 12 13 14 15 16 17

3
Installation Guide
AT-UHD-SW-510W
The AT-UHD-SW-510W provides an RS-232 port which allows communication between an
automation system and an RS-232 device. This step is optional.
1. Use wire strippers to remove a portion of the cable jacket.
2. Remove at least 3/16” (5 mm) from the insulation of the RX, TX, and GND wires.
3. Insert the TX, RX, and GND wires into correct terminal using one of the included 3-pin
captive screw connectors.
NOTE: Typical DB9 connectors use pin 2 for TX, pin 3 for RX, and pin 5 for ground.
On some devices functions of pins 2 and 3 are reversed.
RS-232
GND
RX
TX
The AT-UHD-SW-510W provides the ability to output two-channel balanced analog audio on the
AUDIO OUT port, using the included 5-pin captive screw connector. This step is optional.
Use wire strippers to remove enough insulation to allow each wire to be securely fastened
to each terminal of the captive screw connector block and connect the wires as shown.
Unbalanced audio is not supported.
Audio
1 2
3
1 2
3
GND GND
+
-+
-
Balanced XLR audio

4
Installation Guide
AT-UHD-SW-510W
Relay
The AT-UHD-SW-510W provides a RELAY port, allowing the control of screens, curtains, and
other devices. Use a 48 V DC relay with no more than 1 A current draw.
When the AT-UHD-SW-510W is powered-on or rebooted, C1 and C2 are set to the Normally
Open (NO) state.
C2
COM
C1
Trigger
The TRIGGER I/O allows voltage-controlled devices, such as an occupancy sensor, to be
connected to the AT-UHD-SW-510W. Use the included 4-pin captive screw connector to
connect the device. Voltage range is 3 to 30 V DC.
Powered sensor
Passive sensor
Control (Set HIGH)
+12 V DC
Passive sensor
- + P
Common (Set LOW)
Control (Set HIGH)
Powered sensor
30 V (max.)
- + P

5
Installation Guide
AT-UHD-SW-510W
Power Connector
Locate the included orange captive screw connector and wire the included power supply to the
block, as shown below. Do not use high-torque devices, when securing the wires, as this may
damage the screws and/or connector block.
Black
White
19 V DC
power supply
Mounting Instructions
The AT-UHD-SW-510W can be mounted in dierent ways, based on the number of units that are
being installed. The AT-UHD-SW-510W can be mounted in a rack or on/under any at surface.
Single-unit rack installation
1. Attach the included small rack ear to one side of the AT-UHD-SW-510W, using the included
screws.
2. Attach the included longer rack ear to the opposite side of the AT-UHD-SW-510W using the
included screws.
AT-RON-444
+
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAYINPUT
AT-UHD-SW-510W

6
Installation Guide
AT-UHD-SW-510W
Dual-unit rack installation
1. Turn both units upside-down on a at surface, next to each other, as shown.
2. Position the included mounting plates over the pre-drilled holes on the bottom of the
enclosure. When attaching mounting plates, the countersink bevels on the mounting plate
should face upward.
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
Countersink bevel
AT-RON-444
+
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAYINPUT
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAYINPUT
AT-UHD-SW-510W
AT-RON-444
3. Turn the attached units over and install the included rack ears to one side of each enclosure
using the included screws.

7
Installation Guide
AT-UHD-SW-510W
Flat surface
1. Turn the unit upside down a at surface.
2. Position the included mounting plates over the pre-drilled holes on the bottom of the
enclosure. When attaching mounting plates, the countersink bevels on the mounting plates
should face upward.
3. Mount the unit using the circular holes, on each mounting plate. If using a drywall surface,
a #6 drywall screw is recommended. Mounting screws are not included.
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
AT-RON-444
+
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAYINPUT
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
USB-C
DP
HDMI 3
HDMI 4
BYOD
DISPLAY
INPUT
AT-UHD-SW-510W
Countersink bevel
NOTE: The unit can also be mounted under a at surface, such as a table, by
turning the unit upside down.

8
Installation Guide
AT-UHD-SW-510W
DC48V RS-232 HDBaseTIN HDMI OUT
RX TX
Video (DisplayPort)
Video (HDMI)
AT-UHD-SW-510W
USB Wireless Antenna
AT-UHD-EX-100CE-RX-PSE
Ethernet
HDBaseT
Video (HDMI)
Video (HDMI)
Blu-ray Player
Media Player
USB-C
LAN
4
media4
Laptop
Laptop
HD/UHD display
Connection Diagram
1. Connect a USB-C cable from a source to the USB-C (1) port.
2. Connect a DisplayPort cable from a source to the DP IN (2) port.
3. Connect up to two UHD/HD sources, using HDMI cables, to the HDMI IN (3) and HDMI IN
(4) ports.
4. Connect an HDMI cable from the HDMI OUT port to a UHD/HD display.
5. Connect up to three USB wireless antennae to the WiFi ports.
6. Connect the relay leads from the control motors of the projection screen, blinds, or curtains,
to the relay outputs to the RELAY port, using the included 3-pin captive screw connector.
Use a 48 V DC relay with no more than 1 A current draw.
7. Connect a a trigger device, such as an occupancy sensor switch, to the TRIGGER I/O port.
A 4-pin captive screw connector is required. Voltages from 3 to 30 V are supported.
8. Connect a 3.5 mm analog audio cable from an analog source to the AUDIO IN port.
This audio source can be used to embed analog audio on any of the input sources.
9. Connect an Ethernet cable from the LAN port to the Local Area Network (LAN).
10. Connect an Ethernet cable from the HDBaseT port to an HDBaseT receiver unit, such as
the AT-UHD-EX-100CE-RX-PSE.
11. Connect the included green 5-pin captive screw connector to the AUDIO OUT connector.
12. Connect the included orange captive screw connector block to the DC 19V connector.
13. Connect the included power supply to an available AC outlet.
Installation

9
Installation Guide
AT-UHD-SW-510W
By default, the AT-UHD-SW-510W is set to DHCP mode, allowing a DHCP server (if present) to
assign the unit an IP address. If a DHCP server is not found within 15 seconds, the unit will be
placed in Auto IP mode and use a self-assigned IP address within the range of 169.254.xxx.xxx.
If a static IP address is desired, the IP address of 192.168.1.254 is used by default.
Once the desired IP mode has been selected, use an IP scanner to locate the AT-UHD-SW-510W
on the network. Use the MAC address, printed on the sticker (on the bottom of the unit), to
identify the unit within the IP scanner.
IP Conguration
Switching the IP mode
Auto IP mode
• Static IP mode
Press and hold the DISPLAY button, for approximately 15 seconds, until all input indicators
(USB-C, DP, HDMI 3, HDMI 4, and BYOD) on the front panel blink twice.
• DHCP mode
Press and hold the DISPLAY button, for approximately 15 seconds, until all input indicators
(USB-C, DP, HDMI 3, HDMI 4, and BYOD) on the front panel blink four times.
If the AT-UHD-SW-510W is unable to detect a DHCP server within 15 seconds, then the unit will
use a self-assigned IP address within the range of 169.254.xxx.xxx. If this occurs, connect the
AT-UHD-SW-510W to a computer running Microsoft Windows® and follow the procedure below.
1. Click Start > Settings > Control Panel > Network and Sharing Center.
2. Click Change adapter settings.
3. Right-click on the adapter that is used to establish a wired connection to the network, and
select Properties from the context menu.
4. Under the Ethernet Properties dialog box, select Internet Protocol Version 4 and then
click the Properties button.
5. Click the Use the following IP address radio button.
6. Enter the desired static IP address or the IP address provided by the network administrator.
If the PC does not require Internet access or if a statically-assigned IP address is being
used, then an IP address of 169.254.xxx.xxx can be entered.
7. Set the subnet mask to 255.255.0.0.
8. Click the OK button then close all Control Panel windows.
IMPORTANT: Before continuing, write down the current IP settings in order to
restore them, later. If Obtain an IP address automatically and Obtain DNS
server automatically are selected, then this step is not required.

10
Installation Guide
AT-UHD-SW-510W
webGUI
The AT-UHD-SW-510W includes a built-in webGUI, which allows easy management and control
of all features. Follow the instructions below to access the webGUI.
1. Make sure that an Ethernet cable is connected between the LAN port on the AT-UHD-SW-
510W and the network.
2. Launch a web browser and enter the IP address of the unit. If the default static IP address
is being used, enter 192.168.1.254.
3. The AT-UHD-SW-510W Login page will be displayed.
4. Enter the following information on the Login page.
Login: root
Password: Atlona
5. Click the Login button.

11
Installation Guide
AT-UHD-SW-510W
Troubleshooting
Problem Solution
The source image is not
displayed.
• Check all cable connections between the AT-UHD-SW-
510W and the source(s) and display.
• Check the input indicators on the front panel to make
sure that the correct input is selected. Press and release
the INPUT button to cycle through each input.
• Try switching to another input to verify all source
connections.
Auto-switching is not
working.
• Check all cable connections between the AT-UHD-SW-
510W and source devices. If the cable between the
source and the AT-UHD-SW-510W is damaged or is not
secure, then this will prevent auto-switching from working
correctly.
• Verify that audio switching is set to ON, under the
Conguration menu in the webGUI.
The USB-C port is not
charging my USB device.
• Check that the USB cable is not damaged and provides
a secure connection between the AT-UHD-SW-510W and
the USB device.
• Check the voltage rating of the connected device to
make sure it is compatible. Maximum power and voltage
ratings for the USB-C port are as follows: 60 W at 20 V,
36 W at 12 V, and 15 W at 5 V.
The AT-UHD-SW-510W is
not controlling the display.
• Verify the wiring of the RS-232 captive screw connector.
• Make sure that the proper command syntax is being
used; use an RS-232 terminal emulator to verify the
command.
• Check that the proper baud rate, device ID, control
method for the display, and control settings for the AT-
UHD-SW-510W are correct.
• Check CEC settings on the display.

12
Installation Guide
AT-UHD-SW-510W
© 2017 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Version 1
atlona.com •408.962.0515 •877.536.3976