ATOMSTACK A 5 Pro User manual

AT O M S TA C K A 5 P r o L a s e r
E n g r a v e r
I n s t a l l a t i o n M a n u a l
English
Deutsche
Français
Italiano
Español
Polskie

Part 1： Security statement and warning
Before Using the laser engraving, please read this safety guide carefully, it mentions situations that require special attention and includes
warnings of unsafe practices that can cause damage to your property or even endanger your personal safety.
1.This product is a laser engraver system components, must be installed in other manufacturers of laser engraver for use.And the product belongs
to Class 4 laser products, the laser system itself must meet the requirements of IEC 60825-1 latest version, otherwise the product is prohibited
to be used.
2.Your laser engraver shall have a protective housing which, when in place, prevents human access to laser radiation.
3.If a protective housing is equipped with an access panel which provides "walk-in" access then:
a)means shall be provided so that any person inside the protective housing can prevent activation of a laser hazard that is equivalent to Class 3B
or Class 4;
b）a warning device shall be situated so as to provide adequate warning of emission of laser radiation equivalent to Class 3R in the wavelength
range below 400 nm and above 700 nm, or of laser radiation equivalent to Class 3B or Class 4 to any person who might be within the protective
housing;
c)where “walk-in” access during operation is intended or reasonably foreseeable, emission of laser radiation that is equivalent to Class 3B or
Class 4 while someone is present inside the protective housing of a Class 1, Class 2, or Class 3R product shall be prevented by engineering means.
NOTE Methods to prevent human access to radiation when persons are inside the protective housing can include pressure sensitive floor mats,
infrared detectors, etc.
4.The laser itself has a protective cover, the protective cover is fastened by screws. When the laser is installed on the laser engraver, the
protective cover should be checked to be reliably locked, and can not be removed in the energized state;
5.The housing of the laser engraver should have an interlock function. When the housing is opened or removed, the laser can be automatically
turned off.
6.The laser engraver should have an emergency stop button, which can immediately stop the output of the laser when pressed under unexpected
circumstances;
7.The laser engraver should have a reset button, which can resume work under the condition of confirming safety after lifting the interlock or
emergency stop;
8.Laser engraver should use physical keys, dongle, password system and other ways to manage and control, to prevent personnel without security
training operation of this kind of equipment;
9.On the laser engraver any window or channel that can actively observe or passively receive the laser radiation should be set up warning marks;
10.If the laser burns the skin or eyes, please go to a nearby hospital for examination and treatment immediately

Part 2: Disclaimer and warning
Thisproductisnotatoyandisnotsuitableforpeopleunder15yearsofage.Donotallowchildrentotouchthe
laser Module.Pleasebecarefulwhenoperatinginsceneswithchildren.
Thisproductisalaser
module,visithttp://www.atomstack3d.com/laserengraverdownloadforcomplete"usermanual"andthelatestinstructio
nsandwarnings.ShenzhenAtomStackTechnologiesCo.,Ltd.(Atomstack)reservestherighttoupdatethisDisclaime
randSafeOperationGuidelines.
Pleasebesuretoreadthisdocumentcarefullybeforeusingtheproducttounderstandyourlegalrights,responsibi
litiesandsafetyinstructions;Otherwise,itmaybringpropertyloss,safetyaccidentandhiddendangerofpersona
lsafety.Onceyouusethisproduct,youshallbedeemedtohaveunderstood,acceptedandacceptedalltermsandco
ntentsofthisdocument.Userundertakestoberesponsibleforhisorheractionsandallconsequencesarisingther
efrom.UseragreestousetheProductonlyforlegitimatepurposesandagreestotheentiretermsandcontentsoft
hisdocumentandanyrelevantpoliciesorguidelinesthatAtomStackmayestablish.
You understand and agree that AtomStack may not be able to provide you with the cause of the damage or accident and
provide you with AtomStack's after-sale service unless you provide the original engraving or cutting files,
engraving software configuration parameters used, operating system information, video of the engraving or cutting
process, and operational steps prior to the occurrence of a problem or failure.
AtomStackisnotliableforanyandalllossesarisingfromtheuser'sfailuretousetheproductinaccordancewit
hthismanual.
Atomstackhastheultimaterighttointerpretthedocument,subjecttolegalcompliance.Atomstackreservestherig
httoupdate,modify,orterminatetheTermswithoutpriornotice.

Part 3：Installation Steps
Step1.Install the contour of the engraving machine
Step2.Install X axis assembly, control box and support frame
Step3.Install belt and aluminum profile end cap
Step4.Install laser and laser protective cover
Step5.Install the Y-axis limit column and adjust the X and Y-
axis eccentric screws
Step6.Install the cable and fix the cable

S t e p 1
Installation Manual:
1. Find the four large profiles in the picture
above, place the four profiles as shown, and
pay attention to the direction of the profiles.
2. Tighten the M5 screw in the shaft, and
judge whether you have installed it correctly
through the enlarged view details.
Nota:
a. Place the screws, but do not tighten them.
b. Then tighten the screws diagonally.
c. Tools required, M5 Allen key+M5 screws.
Logo side
up
The hole side faces
outward
Cut side
outward
X
Y
Tick mark font
direction
Step1 Required components:

S t e p 2
Installation Manual:
1.Push the X-axis component into the base
frame in the direction shown in the figure. Adjust
the eccentric nut appropriately.
2.Install the control box as shown.
3. Use an M5 Allen key to install 3 Support
gasket.
Control box *1 M5 screws*8 Support gasket
*3
X-axis components*1
Step2 Required
components:
1
1
2
3
3
3The guide rail passes through
the middle of the 3 rollers.
Loosen the distance between
the upper and lower guide
wheels appropriately.
Y
X

Step 3
Installation Manual:
1. Install two synchronous belts as shown in the figure.
First tighten one end with a T-nut, then pass the other
end through the roller on the X-axis assembly as shown
in the figure, and finally tighten the other end and fix it
with a T-nut.
2. T-nut fixing method (Push the T-nut from the groove on
the end of the profile, and then use the screw to tighten
the T-nut), the T-nut is as close to the end of the profile
as possible, and cut off the excess belt.
3. Cover the profile end cover (the side of the end cap
with protrusions is facing down)
TIPS:
The installation of the Y-axis synchronous belt can refer
to the installed synchronous belt on the X-axis
assembly.Determine whether the timing belt is tight
enough: press the position shown in Figure 4 with your
fingers, and if there is no obvious deformation, it is tight
enough. If the deformation is large, loosen one end of
the T-nut and tighten the timing belt, and then tighten the
T-nut.
1
3
3
3
3
Type T Nut *4 Type T Nut Lock
screws*4
2
Profile end cover *4Synchronous belt *2
Step3 Required
components:
4
Tighten the T nut
and cut off the
excess belt.
5

S t e p 4
Installation Manual:
1. Fix the laser head on the slider board
with M5*8 countersunk head screws. The
screws must be tightened.
2. Insert the green protective covers on the
left and right sides.
3. Insert the front green protective cover.
4. Fix the front protective cover with M5*14
flat round head screws.
2
3
4
1
1
2
3
4
Y
X
Front protective
cover *1
Protective covers on both sides
*2
Laser head *1
M5*14 Flat round head
screw*1
M5*8 Countersunk screw
*2
Step4 Required components:

Installation Manual:
1. As shown in the figure, fix the Y-axis limit
column with M3*14 screws on the left slide rail.
2. Adjust the eccentric nut to ensure that the X-
axis and Y-axis move smoothly without shaking.
TIPS：
How to determine the tightness of eccentric nuts?
Under the condition of ensuring that the bracket does
not shake, you can lift one end of the machine to an
angle of 45 degrees with the horizontal plane, and
release the X-axis or Y-axis bracket from a high
place. If the bracket can slide at a constant speed to
the end, the tightness is suitable.
Y
X
M3*14Screw*2 Y-axis limit column *2
Step5 Required components:
S t e p 5
Use a wrench to turn the eccentric
nut to adjust the tightness of the
guide wheel and the guide rail

S t e p 6 I n s t a l l a t i o n o f t e r m i n a l b l o c k s a n d c a b l e
bundle
Installation Manual:
1. Insert the three wire terminals as shown
2. As shown in the figure, tie the machine
fixing hole and the cable bundle with a cable
tie to prevent the wire terminal from
loosening.
1
2

Laser Light can damage the human eyes and skin. Do not expose the eye or skin
to laser light directly. This Laser product has an optical lens and emits a
collimated laser beam. The light from this product, both direct and reflected, is
very harmful as it can propagate a long distance while maintaining high optical
density. When handling the product, wear appropriate safety glasses (OD5+) to
protect eyes from laser light including reflected and stray light. The reflected and
stray light spilling into an unintended area should be attenuated and/or absorbed.
Part 4：Cautions
LASER BEAM CAN DAMAGE EYES

Part 5：Maintenance instructions and warning
T h i s p r o d u ct use s a h i g h l y i n t e g rated d e s i g n a n d r e quires no m a i n t e n a n c e . How ev e r , i f t h e
l a s e r s y s te m i n s t al l e d w i t h th i s p r od u c t n ee d s t o be r e p ai r e d o r t un e d , pl e a s e :
1 . U n pl u g th e p o w e r co r d o n t h e l a s e r , s o t h a t t h e l a se r i s i n a s t at e o f po w e r f ai l u r e ;
2 . I f y o u n e ed l a s e r as s i s t an c e f o r t u n i n g , p l e a s e :
1 . Al l p r e s e n t p e r s o n n e l w e a r p ro t e c t iv e g l a s s e s , OD 5 + p r o t e ct i v e gl a s s i s n e ed e d ;
2 . Ma k e s u re t h e r e a r e no f l a m ma b l e o r ex p l o s i v e ma t er i a l s a r o u n d;
3 . Th e p o s i t i on a n d d i r e ct i o n of t h e la s e r a r e f i x e d to e n s u r e t h a t t h e l a s e r w i l l n ot
a c c i de n t a ll y m o v e a nd s h i n e o n p e o pl e , a n i m a l s, f l a m m ab l e , ex p l o s i v e an d o t h er
d a ng e r o u s a n d v a l u a b le o b j e c t s d u r i n g de b u g g i n g .
4 . Do n ' t l o o k at l a s e r s
5 . Do n o t s h in e t h e la s e r o n t h e m ir r o r o bj e c t , l es t t h e l a s e r r ef l e c t i o n c a u s e
a c c i de n t a l i n j u r y .

Customer Service:
Ø For detailed warranty policy,please visit
our official website at:
www.atomstack3d.com
Ø For Laser Engraver technical support
and service,please email:
[e-mail]
Manufacturer: Shenzhen AtomStack Technologies Co., Ltd.
Address: AB301,New Chabridge Industrial Park,No.3,Baolong 6th
Rd.,Longgang Dist,Shenzhen,Guangdong,CHINA 518116
View the multilingual
instructions here:
Scanner APP:
QR Code Reader
/Barcode Scanner
or any APP with
scanner