AudioCodes Mediant 500L MSBR User manual

1 |Page
Mediant 500L Gateway and E-SBC
Quick Setup Guide
Welcome
Congratulations on purchasing your AudioCodes Mediant 500L Gateway and Enterprise Session Border
Controller (hereafter, referred to as device)!
This document is only intended to provide basic setup instructions for initial access to the device and
connecting it to your network. For advanced configuration and cabling, refer to the User's Manual and
Hardware Manual respectively, which can be downloaded from AudioCodes Website at
https://www.audiocodes.com/library/technical-documents.
Before you begin, please read the Safety Precautions on page 7.
Package Contents
Make sure that the following items (in addition to any separate-orderable items that you may have purchased)
are included with your shipped device:
4 x anti-slide bumpers for desktop mounting
1 x AC/DC power adapter
Regulatory Information document
This document

2 |Page
Physical Description
[The number and type of port interfaces depend on the ordered hardware configuration.]
1
POWER
AC power plug entry
Power LED (located on the front panel):
Green On
Power received by device
Off
No power
Status LED (located on the front panel):
Green On
Device is operational
Green Flashing
Initial rebooting stage or software upgrade (.cmp
file) in process
Red On
Boot failure
Off
Advanced rebooting stage
2
ON / OFF
Power button to switch on the device (when pressed in) and to switch off the
device (when pressed out).
3
CONSOLE
RS-232 serial interface port (RJ-45).
4
USB port, which you can use for various functionalities such as storing the
configuration file on an external USB hard drive.
5
//
Reset pinhole button for resetting the device or restoring it to factory defaults. To
restore the device to factory defaults: with a paper clip or any other similar
pointed object, press and hold down the button for at least 12 seconds (but no
more than 25 seconds).
6
S1 GE LAN
Up to four Gigabit Ethernet (10/100/1000Base-T) ports (RJ-45) for connecting IP
phones, computers, or switches. The ports support 1+1 Ethernet port redundancy
(active-standby), half- and full-duplex modes, auto-negotiation, and straight-
through or crossover cable detection.
Green On
Ethernet link established
Green Flashing
Data is being received or transmitted
Off
No Ethernet link
1
2
3
4
5
6

3 |Page
Mounting the Device
You can mount the device in several ways:
Placing it on a desktop using the four anti-slide bumpers (supplied), which you need to stick on the
grooves located on the underside of the device.
Mounting it in a standard 19-inch rack by placing it on AudioCodes 1U 19-inch rack mount shelf
(separate orderable item). The procedure includes attaching the shelf to the rack's front posts, and
then placing the device on the shelf where it is securely held in position by the device's anti-slide
bumpers which fit into the shelf's four square-openings.
Mounting it on a wall, using the integral mounting keyholes located on its underside.
For detailed instructions on mounting, refer to the Hardware Manual.

4 |Page
Cabling the Device
The device is powered by an external 12V/3A AC/DC power adapter (supplied), connected to a standard
alternating current (AC) electrical wall outlet.
1. The AC/DC power adapter (supplied) supports interchangeable plugs to suit the type of electrical wall
outlet of the country in which you are installing the device. To attach the required plug to the adapter,
insert the top part of the plug into the upper part of the adapter's housing slot, and then press down
on the bottom part of the plug until you hear a "click" sound, indicating that the plug is securely
inserted into the slot. (To remove the plug, push and slide down the adapter's OPEN plug release
lever.)
2. Insert the DC plug that is located at the end of the power cord of the power adapter into the device's
power socket located on the rear panel and labeled POWER.
3. Plug the power adapter directly into a standard electrical wall outlet.
4. Switch on the device by pressing-in the power button located on the rear panel. When the device
receives power, the Power LED turns on (green).

5 |Page
Assigning an IP Address to the Device
Use the device's factory default IP address (192.168.0.2/24 and Default Gateway 0.0.0.0) to initially access the
device's Web-based management interface and then change it to suit your networking addressing scheme for
subsequent connectivity.
1. Using a CAT-5e/6 straight-through RJ-45 Ethernet cable, connect the device's Ethernet port GE LAN #1
(front panel) to the LAN port of your computer.
2. Change the IP address of your computer to correspond with the device's default IP address and subnet
mask.
3. On your computer, open a standard Web browser (for example, Google Chrome), and then in the URL
field, enter the device's default IP address; the Web Login screen appears:
4. Type in the default username (Admin) and password (Admin), and then click Login.
5. Open the IP Interfaces table (Setup menu > IP Network tab > Core Entities folder > IP Interfaces).

6 |Page
6. Select the OAMP interface ('Application Type' with OAMP + Media + Control), click Edit, and then in
the dialog box, modify the device's OAMP interface.
7. Click Apply to submit your changes.
8. On the toolbar, click Reset to access the Maintenance Actions page.
9. On the Maintenance Actions page, click Reset to save your new settings to flash memory with a device
reset.
10. Disconnect the device's Ethernet cable from the computer and connect it to your network.
11. Access the device's management interface using the new IP address that you assigned the device.

7 |Page
Safety Precautions
This device is an indoor unit and therefore, must not be installed outdoors.
Ethernet cabling must be routed only indoors and must not exit the building.
The device must be installed and serviced only by qualified service personnel.
Do not open or dismantle the device.
Do not expose the device to water or moisture.
Make sure the device is installed in a well-ventilated location to avoid over heating of internal
components and subsequent damage.
Do not place any object on top of the device and make sure that sufficient clearance from the top and
sides are maintained to ensure proper airflow to avoid over heating of internal components.
Operate the device in an ambient temperature (Tma) that does not exceed 40°C (104°F).
The device must be installed only in restricted access locations.
Use only the supplied AC/DC power adapter for connection to the power source.
In case of a malfunction, do not attempt to fix the power adapter and do not use any other type of
power adapter. Contact AudioCodes for further assistance.
Operate the device only from the type of power source indicated on the chassis.
Installation of the device must be in accordance with national electrical codes and conform to local
regulations.
Use minimum 26-AWG wiring for FXO ports.

8 |Page
About AudioCodes
AudioCodes Ltd. (NasdaqGS: AUDC) is a leading vendor of advanced voice networking and media processing
solutions for the digital workplace. With a commitment to the human voice deeply embedded in its DNA,
AudioCodes enables enterprises and service providers to build and operate all-IP voice networks for unified
communications, contact centers and hosted business services. AudioCodes’ wide range of innovative
products, solutions and services are used by large multinational enterprises and leading tier one operators
worldwide.
International Headquarters
1 Hayarden Street,
Airport City
Lod 7019900, Israel
Tel: [phone]
Fax: [phone]
AudioCodes Inc.
27 World’s Fair Drive,
Somerset, NJ 08873
Tel: [phone]
Fax: [phone]
Contact us: https://www.audiocodes.com/corporate/offices-worldwide
Website: https://www.audiocodes.com/
©2018 AudioCodes Ltd. All rights reserved. AudioCodes, AC, HD VoIP, HD VoIP Sounds Better, IPmedia, Mediant,
MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your
Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice and CloudBond are trademarks or registered trademarks of
AudioCodes Limited. All other products or trademarks are property of their respective owners. Product specifications are
subject to change without notice.
Document #: LTRT-10702