Johnson Controls Simplicity LINC User guide

1031990-UAD-A-0313
APPLICATION GUIDE
OVERVIEW
The Simplicity®LINC Gateway operates as a Modbus® Client
providing an interface between a BACnet® MS/TP control system
and devices that communicate using the Modbus RTU protocol.
The Simplicity®LINC allows monitoring and control by a third-party
BACnet Building Automation System (BAS).
The Simplicity®LINC is preconfigured to provide an interface to UP
products equipped with Simplicity®controllers manufactured after
4/2/2008 as well as prior Simplicity®Elite™ and Simplicity®with
Intelli-Comfort™ controllers.
The Simplicity®LINC mounts inside the control panel of the UP
unit and utilizes 24 VAC power from the unit’s control transformer.
One port is connected to the UP controller. The other port must be
connected to the BACnet MS/TP network.
The Simplicity®LINC Gateway is preconfigured to obtain
operational data points from the controller and expose them on a
BACnet MS/TP network.
NOTE: Not all Simplicity®operating parameters are controlled/
monitored by the Simplicity®LINC.
FIGURE 1: WIRE CONNECTIONS
24 — must be grounded
close to the Simplicity LINC
®
The shield must be
connected to ground at
each device.
R
C
24V power is polarity sensitive, incorrect
wiring could result in board damage.
Simplicity®LINC GATEWAY
ConFig v1.01d

1031990-UAD-A-0313
2 Johnson Controls Unitary Products
CONNECTION
The Simplicity®LINC has 2 ports, one for connection to the BAS
network (BACnet) and one to the Simplicity®board (Modbus).
BACNET NETWORK
The only connection required in the field is to the BACnet (BAS)
network.
NOTE: Proper termination and grounding of the shields must
be observed.
DIP switches A0-A7 on the Simplicity®LINC board allow
selection of the MAC Address. The MAC Address identifies the
Simplicity®LINC to other devices and must be between 1 and
99. The default DIP switch setting is 1.
A Device Instance (DE) Modifier is used by the Simplicity®LINC
and defaulted to 230. The combination of the DE Modifier and
the default DIP switch setting creates a default DE of 23001.
The default Unit Name is YORK_RTU.
FIGURE 2: MAC ADDRESS EXAMPLES
DIP switches B0-B3 on the Simplicity®LINC board allow for
selection of the BACnet transfer speed.The default speed is set
at 38.4k baud. Other speeds can be chosen as shown in Table
1
.
MAC Address of 21
1
0
4
0
16
0
0
0
21
1
2
0
0
0
32
64
0
99
MAC Address of 99
1
2
4
8
16
32
64
128
ON
1 2 3 4 5 6 7 8
1
2
4
8
16
32
64
128
ON
1 2 3 4 5 6 7 8
A0
A1
A2
A3
A4
A5
A6
A7
A0
A1
A2
A3
A4
A5
A6
A7
TABLE 1: BAUD RATE SELECTION SETTINGS
DIP Setting Baud Rate
1 110
2 300
3 600
4 1200
5 2400
6 4800
7 9600
8 19200
9 20833
10 28800
11(Default) 38400
12 57600
13 76800
14 115200
1
2
0
8
11
1
2
4
8
ON
1 2 3 4
B0
B1
B2
B3
Baud Rate of 38400

1031990-UAD-A-0313
Johnson Controls Unitary Products 3
MODBUS CONNECTION
The UP device communicates with the Simplicity®LINC using
the Modbus RTU protocol on an RS485 connection. Connection
and addressing of the UP product is completed at the factory.
No further adjustment should be done.
If a problem arises with the Simplicity®LINC or a parameter not
exposed by the Simplicity®LINC requires modification, the UP
controller software can be manipulated using a Microsoft©
Windows-based PC with the Simplicity®PC software
(downloadable from the UP website). To connect the PC to the
UP controller, a FREEnet USB adaptor (Part No.
S103101967000), which is an RS232 to RS485 adapter, and
FREEnet adapter cable (S102538682000) are required and
available through SOURCE1 (Toll-free at 1-800-536-6112).
SOFTWARE SETUP
The control sequence is managed by the Simplicity®controller.
The data points on these systems are mapped to standard
BACnet Objects. As a preconfigured application, no
configuration is necessary in the Simplicity®LINC Gateway.
FLASH MEMORY MANAGEMENT
The Flash Memory chip used in the Simplicity®controllers has
a 1,000,000 write cycle rating.
To prevent premature failure of the flash memory, it should not
be written to more often than once every 10 minutes, on
average.
The default Simplicity®board address is 1 and must
remain on address 1 to correctly communicate with
Simplicity®LINC. To change the address to 1, press the
Com/Setup button 3 times in succession.
Under unusual circumstances it could take up to two
minutes for newly updated data to be seen.
This product has been
tested at a qualified BACnet
testing laboratory and
found to comply with all the
necessary interoperability
requirements.

1031990-UAD-A-0313
4 Johnson Controls Unitary Products
TABLE 2: POINTS LIST IN DESCRIPTION ORDER
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description
R / W (5) BV 109 COMM_IAQ n/a n/a n/a Accept Comm Value for Indoor Quality
Sensor
R / W (5) BV 101 COMM_OAT n/a n/a n/a Accept Comm Value for OAT
R / W (5) BV 100 COMM_OH n/a n/a n/a Accept Comm Value for OH
R / W (5) BV 99 COMM_RH n/a n/a n/a Accept Comm Value for RH
R / W (5) BV 108 COMM_ST n/a n/a n/a Accept Comm Value for Space
Temperature
R / W (2) AV 14 ACC_OVER_TME n/a n/a n/a Accumulated Unoccupied Override
Time (in hours)
R (2) AI 15 ACTIVE_ALARM n/a n/a n/a Active Alarm
R (2) AI 86 AIR_MON_INPUT 0 0 10 Air Monitor Station Input
R (5) BI 16 AIR_PROOF_SW n/a n/a n/a Air Proving Switch Status (1=closed,
0=open / no air flow)
R / W (2) AV 79 OAQ_STPT 1000 0 5000 Air Quality Setpoint Outside
R (5) BI 85 ALARM_1_ON n/a n/a n/a Alarm Buffer #1 (0=Alarm has cleared,
1=Alarm is still active)
R (5) BI 86 ALARM_2_ON n/a n/a n/a Alarm Buffer #2 (0=Alarm has cleared,
1=Alarm is still active)
R (5) BI 87 ALARM_3_ON n/a n/a n/a Alarm Buffer #3 (0=Alarm has cleared,
1=Alarm is still active)
R (5) BI 88 ALARM_4_ON n/a n/a n/a Alarm Buffer #4 (0=Alarm has cleared,
1=Alarm is still active)
R (5) BI 89 ALARM_5_ON n/a n/a n/a Alarm Buffer #5 (0=Alarm has cleared,
1=Alarm is still active)
R (2) AI 33 BLDG_STATIC n/a n/a n/a Building Static Pressure
R / W (5) BV 29 BP_SENS_INST n/a n/a n/a Building Static Pressure Sensor
Installed
R / W (2) AV 57 BLDG_SP_STPT 0.15 -0.25 0.25 Building Static Pressure Setpoint
R / W (2) AV 25 COM_V_LOW_SP 70 60 80 Comfort Ventilation LowerSetpoint
(degrees F)
R / W (5) BV 34 CVM_COOLING n/a n/a n/a Comfort Ventilation Mode for Cooling
Enabled
R / W (5) BV 35 CVM_HEATING n/a n/a n/a Comfort Ventilation Mode for Heating
Enabled
R (5) BI 33 COM_VENT_STA n/a n/a n/a Comfort Ventilation Mode Status
(1=control is in Comfort Vent mode, 0= it
is not)
R / W (2) AV 24 COM_V_HI_SP 80 65 85 Comfort Ventilation Upper Setpoint
(degrees F)
R / W (5) BV 23 COOLING_ENA n/a n/a n/a Cooling Mode Enabled
R (2) AI 56 CV_VAV_SELEC n/a n/a n/a CV / VAV Selected (0= Valid CV,
1=Valid VAV, 2= Invalid Value)
R / W (5) BV 21 FAN_ON_W_SEN n/a n/a n/a CV-Indoor Fan Operates with Space
Sensor Present Option Enabled
R / W (2) AV 8 IAQ_VALUE n/a 0 5000 Demand Ventilation (IAQ) Value (PPM)

1031990-UAD-A-0313
Johnson Controls Unitary Products 5
R / W (5) BV 39 DEMAND_VENT n/a n/a n/a Demand Ventilation (using Inside
Sensor) Enabled
R / W (2) AV 18 DEMVENT_STPT 1000 0 5000 Demand Ventilation Setpoint
R (2) AI 67 REVISION n/a n/a xx Device Revision
R / W (5) BV 98 DIFF_ENTH_MODE n/a n/a n/a Differential enthalpy mode enabled
R / W (5) BV 90 DF_SW_INST n/a n/a n/a Dirty Filter Switch Installed
R (5) BI 15 DIRT_FILT_SW n/a n/a n/a Dirty Filter Switch Status
(0=open,1=closed / fault)
R (2) AI 35 DUCT_STATIC n/a n/a n/a Duct Static Pressure
R / W (2) AV 58 DUCT_SP_STPT 1.5 0 5 Duct Static Pressure Setpoint
R / W (2) AV 59 DUCT_SD_STPT 4.5 0 5 Duct Static Pressure Shutdown Setpoint
R / W (2) AV 87 ECON_MIN_POS_LP 25 0 100 Econ Minimum Position For Low Speed
Fan
R (2) AI 31 ECO_DAMP_OUT n/a n/a n/a Economizer Damper Output Status (0-
100%)
R / W (2) AV 20 ECO_1ST_STPT 55 40 65 Economizer First Stage Setpoint
R / W (5) BV 7 ECONO_INST n/a n/a n/a Economizer Installed
R / W (5) BV 36 ECO_L_TO_SAT n/a n/a n/a Economizer Loading to Control Supply
Air Temperature Enabled
R / W (2) AV 19 ECON_MIN_POS 20 0 100 Economizer Minimum Position
R (5) BI 31 ECONO_STATUS n/a n/a n/a Economizer Output Status (0=not Free
Cooling, 1= Free Cooling)
R / W (2) AV 22 ECON_OAEN_SP 27 10 50 Economizer Outside Air Enthalpy
Setpoint
R / W (2) AV 23 ECON_OAT_ENA 55 40 80 Economizer Outside Air Temperature
Enable Setpoint
R / W (2) AV 84 ECON_RAEN_SP 27 10 50 Economizer Return Air Enthalpy
Setpoint
R / W (2) AV 21 ECO_2ND_STPT 50 40 65 Economizer Second Stage Setpoint
R (2) AI 41 E_C1_ACM_HRS n/a n/a n/a Elite Compressor #1 Accumulated Run
Time (in hours)
R (5) BI 42 E_COMP1_STAT n/a n/a n/a Elite Compressor #1 Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 45 E_C1_OVRLOAD n/a n/a n/a Elite Compressor #1 Overload Switch
Input Status (1=closed, 0=open / fault)
R (2) AI 42 E_C2_ACM_HRS n/a n/a n/a Elite Compressor #2 Accumulated Run
Time (in hours)
R (5) BI 46 E_COMP2_STAT n/a n/a n/a Elite Compressor #2 Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 49 E_C2_OVRLOAD n/a n/a n/a Elite Compressor #2 Overload Switch
Input Status (1=closed, 0=open / fault)
R (2) AI 43 E_C3_ACM_HRS n/a n/a n/a Elite Compressor #3 Accumulated Run
Time (in hours)
R (5) BI 51 E_COMP3_STAT n/a n/a n/a Elite Compressor #3 Output Status
(0=output is OFF, 1=output is ON)
TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
6 Johnson Controls Unitary Products
R (5) BI 54 E_C3_OVRLOAD n/a n/a n/a Elite Compressor #3 Overload Switch
Input Status (1=closed, 0=open / fault)
R (2) AI 44 E_C4_ACM_HRS n/a n/a n/a Elite Compressor #4 Accumulated Run
Time (in hours)
R (5) BI 55 E_ COMP4_STAT n/a n/a n/a Elite Compressor #4 Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 58 E_C4_OVRLOAD n/a n/a n/a Elite Compressor #4 Overload Switch
Input Status (1=closed, 0=open / fault)
R (5) BI 50 E_CFAN1_STAT n/a n/a n/a Elite Condenser Fan #1 Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 59 E_CFAN2_STAT n/a n/a n/a Elite Condenser Fan #2 Output Status
Input Status (0=output is OFF, 1=output
is ON)
R (5) BI 41 E_FAN_ OVER n/a n/a n/a Elite Fan Overload Switch Input Status
(1=closed, 0=open / fault)
R (5) BI 60 E_GAS_VLVE1 n/a n/a n/a Elite Gas Valve #1 Input Status
(1=energized, 0=not energized)
R (5) BI 62 E_GAS_VLVE2 n/a n/a n/a Elite Gas Valve #2 Input Status
(1=energized, 0=not energized)
R (5) BI 64 E_GAS_VLVE3 n/a n/a n/a Elite Gas Valve #3 Input Status
(1=energized, 0=not energized)
R (5) BI 44 E_HPS1 n/a n/a n/a Elite High Pressure Switch for
Compressor #1 Input Status (1=closed,
0=open / fault)
R (5) BI 48 E_HPS2 n/a n/a n/a Elite High Pressure Switch for
Compressor #2 Input Status (1=closed,
0=open / fault)
R (5) BI 53 E_HPS3 n/a n/a n/a Elite High Pressure Switch for
Compressor #3 Input Status (1=closed,
0=open / fault)
R (5) BI 57 E_HPS4 n/a n/a n/a Elite High Pressure Switch for
Compressor #4 Input Status (1=closed,
0=open / fault)
R (5) BI 40 E_IFAN_STAT n/a n/a n/a Elite Indoor Fan Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 61 E_LIMIT_ 1 n/a n/a n/a Elite Limit Switch #1 Input Status
(1=closed, 0=open / fault)
R (5) BI 63 E_LIMIT_ 2 n/a n/a n/a Elite Limit Switch #2 Input Status
(1=closed, 0=open / fault)
R (5) BI 65 E_LIMIT_ 3 n/a n/a n/a Elite Limit Switch #3 Input Status
(1=closed, 0=open / fault)
R (5) BI 43 E_LPS1 n/a n/a n/a Elite Low Pressure Switch for
Compressor #1 Input Status (1=closed,
0=open / fault)
TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
Johnson Controls Unitary Products 7
R (5) BI 47 E_LPS2 n/a n/a n/a Elite Low Pressure Switch for
Compressor #2 Input Status (1=closed,
0=open / fault)
R (5) BI 52 E_LPS3 n/a n/a n/a Elite Low Pressure Switch for
Compressor #3 Input Status (1=closed,
0=open / fault)
R (5) BI 56 E_LPS4 n/a n/a n/a Elite Low Pressure Switch for
Compressor #4 Input Status (1=closed,
0=open / fault)
R (2) AI 32 EXH_DAMP_OUT n/a n/a n/a Exhaust Damper Output Status (0-
100%)
R (5) BI 30 EX_FAN_STAT n/a n/a n/a Exhaust Fan Output Status (0=output is
OFF, 1=output is ON)
R / W (5) BV 10 EX_VFD_INST n/a n/a n/a Exhaust VFD Installed
R / W (2) AV 91 FAN_SPD_1ST_COOL 70 0 100 Fan Speed: 1st Stage Cooling
R / W (2) AV 92 FAN_SPD_1ST_HEAT 100 0 100 Fan Speed: 1st Stage Heating
R / W (2) AV 93 FAN_SPD_ALL_COOL 100 0 100 Fan Speed: All Stages Cooling
R / W (2) AV 94 FAN_SPD_ALL_HEAT 100 0 100 Fan Speed: All Stages Heating
R / W (2) AV 90 FAN_SPD_NO_HEAT_COOL 50 0 100 Fan Speed: No Heating No Cooling
R (5) BI 102 4_STG_EXP_PRES n/a n/a n/a Four Stage Expansion board Present
R (5) BI 32 FRECOOL_STAT n/a n/a n/a Free Cooling Mode Status (0=comps
not overridden by Econo, 1=comps
overridden)
R (5) BI 104 FREEZE_STAT_1 n/a n/a n/a Freeze Stat # 1
R (5) BI 105 FREEZE_STAT_2 n/a n/a n/a Freeze Stat # 2
R (5) BI 106 FREEZE_STAT_3 n/a n/a n/a Freeze Stat # 3
R (5) BI 107 FREEZE_STAT_4 n/a n/a n/a Freeze Stat # 4
R (5) BI 68 HEAT_1_STAT n/a n/a n/a H1 Heating Output #1 Status (0=output
is OFF, 1=output is ON)
R (5) BI 69 HEAT_2_STAT n/a n/a n/a H2 Heating Output #2 Status (0=output
is OFF, 1=output is ON)
R (5) BI 70 HEAT_3_STAT n/a n/a n/a H3 Heating Output #3 Status (0=output
is OFF, 1=output is ON)
R (2) AI 76 H1_ACCUM_HRS n/a n/a n/a Heating #1 Accumulated Run Time (in
hours)
R (2) AI 77 H2_ACCUM_HRS n/a n/a n/a Heating #2 Accumulated Run Time (in
hours)
R (2) AI 78 H3_ACCUM_HRS n/a n/a n/a Heating #3 Accumulated Run Time (in
hours)
R / W (5) BV 25 HEATING_ENA n/a n/a n/a Heating Mode Enabled
R / W (2) AV 27 HGR_HUM_STPT 50 0 100 Hot Gas Reheat Humidity Setpoint
(percent Humidity)
R (5) BI 18 HGR_STAT n/a n/a n/a Hot Gas Reheat Output Status
(0=output is OFF, 1=output is ON)
TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
8 Johnson Controls Unitary Products
R (2) AI 47 HGR_VLV_OUT n/a n/a n/a Hot Gas Reheat Valve Output Status (0-
100%)
R (5) BI 66 E_FREEZE_ST n/a n/a n/a Hot H2O Freeze Thermostat Switch
Input Status (1=closed, 0=open / fault)
R (2) AI 55 HW_VLV_OUT n/a n/a n/a Hot Water Valve Output Status (0-
100%)
R / W (5) BV 2 HYDRONC_HEAT n/a n/a n/a Hydronic Heat Enabled
R / W (5) BV 3 HH_REVER_VLV n/a n/a n/a Hydronic Heat Reverse Actuated Valve
Installed
R / W (2) AV 62 HYD_S1_SA_SP 120 80 180 Hydronic Heating Stage #1 Supply Air
Setpoint (degrees F)
R / W (2) AV 63 HYD_S2_SA_SP 150 81 180 Hydronic Heating Stage #2 Supply Air
Setpoint (degrees F)
R / W (2) AV 80 IO_DVNT_STPT 700 0 2000 Indoor / Outdoor Demand Ventilation
Setpoint
R (2) AI 45 I_C1_ACM_HRS n/a n/a n/a Intelli-Comfort Compressor #1
Accumulated Run Time (in hours)
R (5) BI 73 I_COMP1_STAT n/a n/a n/a Intelli-Comfort Compressor #1 Input
Status (0=output is OFF, 1=output is
ON)
R (2) AI 46 I_C2_ACM_HRS n/a n/a n/a Intelli-Comfort Compressor #2
Accumulated Run Time (in hours)
R (5) BI 76 I_COMP2_STAT n/a n/a n/a Intelli-Comfort Compressor #2 Input
Status (0=output is OFF, 1=output is
ON)
R (5) BI 79 I_CFAN_STAT n/a n/a n/a Intelli-Comfort Condenser Fan #1 Input
Status (0=output is OFF, 1=output is
ON)
R (5) BI 72 I_FAN_OVER n/a n/a n/a Intelli-Comfort Fan Overload Switch
Input Status (0=open,1=closed)
R (5) BI 82 I_FREEZE_1 n/a n/a n/a Intelli-Comfort Freeze Thermostat
Switch #1 Input Status
(0=open,1=closed)
R (5) BI 83 I_FREEZE_2 n/a n/a n/a Intelli-Comfort Freeze Thermostat
Switch #2 Input Status
(0=open,1=closed)
R (5) BI 80 I_GAS_VLVE1 n/a n/a n/a Intelli-Comfort Gas Valve #1 Input
Status
R (5) BI 75 I_HPS1 n/a n/a n/a Intelli-Comfort High Pressure Switch for
Compressor #1 Input Status (1=closed,
0=open / fault)
R (5) BI 78 I_HPS2 n/a n/a n/a Intelli-Comfort High Pressure Switch for
Compressor #2 Input Status (1=closed,
0=open / fault)
R (5) BI 71 I_IFAN_STAT n/a n/a n/a Intelli-Comfort Indoor Fan Output Status
(0=output is OFF, 1=output is ON)
TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
Johnson Controls Unitary Products 9
R (5) BI 81 I_LIMIT_1 n/a n/a n/a Intelli-Comfort Limit Switch #1 Input
Status
R (5) BI 74 I_LPS1 n/a n/a n/a Intelli-Comfort Low Pressure Switch for
Compressor #1 Input Status (1=closed,
0=open / fault)
R (5) BI 77 I_LPS2 n/a n/a n/a Intelli-Comfort Low Pressure Switch for
Compressor #2 Input Status (1=closed,
0=open / fault)
R / W (5) BV 28 INTELLI-STRT n/a n/a n/a Intelli-Start Enabled
R / W (5) BV 13 LOADSHED n/a n/a n/a Loadshed (0=clear loadshed, 1=set
loadshed operation)
R / W (2) AV 89 LOW_AMB_ECON_MIN 0 0 99 Low Ambient Economizer Minimum
Position (Percent) (0 disables)
R / W (2) AV 88 LOW_AMB_ECON_STPT 0 0 60 Low Ambient Economizer Temperature
Setpoint (0 disables)
R / W (5) BV 19 LOW_AMB_OVRD n/a n/a n/a Low Ambient Temperature (0=comps
not overridden by LAT, 1=comps
overridden)
R (5) BI 14 LOW_SUP_VOLT n/a n/a n/a Low Supply Voltage (0=comps not
overridden by LSV, 1=comps
overridden)
R / W (2) AV 28 MAX_TH_OFSET 3 0 5 Max Temperature / Humidity Setpoint
Offset
R / W (2) AV 30 MAX_DMV_ECON 50 0 100 Maximum Demand Ventillation
Economizer Position
R / W (5) BV 110 MIN_AMB_SEN n/a n/a n/a Minimum Outdoor Air Sensor Enabled
R / W (2) AV 85 MIN_AMB_TEMP_SP 0 0 100% Minimum Outdoor Air Temperature
Setpoint (0-100%)
R (5) BI 11 MODBUS_ALARM n/a n/a n/a Modbus Communication Alarm
R / W (5) BV 9 MOD_EX_INST n/a n/a n/a Modulating Exhaust Installed
R / W (2) AV 61 MWU_RAT_STPT 70 50 85 Morning Warm-Up and VAV Heating:
Return Air Temperature Setpoint
(degrees F)
R / W (5) BV 6 MORN_WARM-UP n/a n/a n/a Morning Warm-Up Enabled
R (2) AI 16 NUMBER_COMPS 2 4 Number of Compressors Available
R (2) AI 48 NUMBER_HEAT n/a n/a n/a Number of Heat Stages Available (0,0, 0
stage, 0,1= 1 stage, 1,0= 2 stage, 1,1= 3
stage)
R / W (2) AV 1 OCC_COOL_SP 72 46 99 Occupied Cooling Setpoint
R / W (2) AV 50 OCC_HEAT_SP 68 45 98 Occupied Heating Setpoint
R / W (5) BV 1 OCCUPIED_ENA n/a n/a n/a Occupied Input Enabled
R / W (5) BV 93 OCC_COMS_ENA n/a n/a n/a Occupied Thermostat or
Communication Input Enabled
R (2) AI 17 OP_COOL_STPT n/a n/a n/a Operating Cooling Setpoint
R (2) AI 49 OP_HEAT_STPT 68 45 99 Operating Heating Setpoint
TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
10 Johnson Controls Unitary Products
R / W (2) AV 69 OP_STPT_DIF 1 1 5 Operating Setpoint Differential
R / W (2) AV 74 OAT_COOL_L_O 45 0 100 Outdoor Air Temperature Cooling
Lockout Temperature
R / W (2) AV 54 OAT_HEAT_L_O 75 0 100 Outdoor Air Temperature
HeatingLockout Temperature
R (2) AI 11 AMB_AIR_ENTH n/a n/a n/a Outside Air Enthalpy
R / W (2) AV 10 AMB_AIR_HUM n/a n/a n/a Outside Air Humidity
R / W (5) BV 37 OAH_SENSOR n/a n/a n/a Outside Air Humidity Sensor Enabled
R / W (2) AV 7 AMB_TEMP n/a n/a n/a Outside Air Temperature
R (2) AI 9 OAQ_VALUE n/a 0 5000 Outside Demand Ventilation (OAQ)
Value (PPM)
R / W (5) BV 8 PWR_EX_INST n/a n/a n/a Power Exhaust Installed
R / W (5) BV 20 POP_ENABLED n/a n/a n/a Pre-Occupancy Purge Enabled
R / W (2) AV 81 POP_HOURS 4 0 23 Pre-Occupancy Purge Time (hours)
R / W (2) AV 82 POP_MINUTES 0 0 59 Pre-Occupancy Purge Time (minutes)
R (5) BI 17 PURGE_SWITCH n/a n/a n/a Purge Switch Status (0=open,1=closed)
R / W (5) BV 12 REDLINE n/a n/a n/a Redline (0=clear redline, 1=set redline
operation)
R (5) BI 4 REM_CONT_ENA n/a n/a n/a Remote Control Enabled
R / W (5) BV 111 REM_CONT_BAS_ECON n/a n/a n/a Remote Control Third Party BAS
Economizer Enable
R (2) AI 13 RET_AIR_ENTH n/a n/a n/a Return Air Enthalpy
R / W (2) AV 12 RET_AIR_HUM n/a n/a n/a Return Air Humidity
R (2) AI 5 RET_AIR_TEMP n/a n/a n/a Return Air Temperature
R / W (5) BV 38 RAH_SENSOR n/a n/a n/a Return/Inside Air Humidity Sensor
Enabled
R / W (2) AV 6 SPACE_TEMP n/a n/a n/a Space (Indoor) Air Temperature
R / W (2) AV 71 SPCE_ALM_TMP 0 0 25 Space Sensor Alarm Temperature
(degrees F, 0 = disabled)
R / W (2) AV 72 SPCE_ALM_TIM 0 0 120 Space Sensor Alarm Time (minutes F, 0
= disabled)
R / W (5) BV 26 SEN_FAULT_EN n/a n/a n/a Space Sensor Fault Override
(Construction Mode) Enabled
R / W (2) AV 73 SP_OFF_RANGE 3 0 5 Space TempratureSensorOffsetRange
(0-5 degrees)
R (2) AI 4 SUP_AIR_TEMP n/a n/a n/a Supply Air Temperature
R / W (2) AV 70 SAT_ALM_COOL 0 0 80 Supply Air Temperature Alarm Setpoint
for Cooling
R / W (2) AV 53 SAT_ALM_HEAT 0 0 120 Supply Air Temperature Alarm Setpoint
for Heating
R / W (5) BV 22 SAT_COOLING n/a n/a n/a Supply Air Temperature Limit for
Cooling Enabled
R / W (2) AV 3 SAT_COOL_SP 50 40 65 Supply Air Temperature Limit for
Cooling Setpoint (degrees F)
TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
Johnson Controls Unitary Products 11
R / W (5) BV 24 SAT_HEATING n/a n/a n/a Supply Air Temperature Limit for
Heating Enabled
R / W (2) AV 52 SAT_HEAT_SP 135 100 180 Supply Air Temperature Limit for
Heating Setpoint (degrees F)
R (2) AI 34 SFAN_VFD_OUT n/a n/a n/a Supply Fan VFD Output Status (0-
100%)
R (2) AI 36 ALARM_1 n/a n/a n/a System Alarm #1
R (2) AI 37 ALARM_2 n/a n/a n/a System Alarm #2
R (2) AI 38 ALARM_3 n/a n/a n/a System Alarm #3
R (2) AI 39 ALARM_4 n/a n/a n/a System Alarm #4
R (2) AI 40 ALARM_5 n/a n/a n/a System Alarm #5
R / W (2) AV 29 TH_OFFSET 5 1 10 Temperature / Humidity % Humidity that
= 1°F of Offset
R / W (2) AV 26 TEM_HUM_STPT 50 20 80 Temperature / Humidity Setpoint
(percent Humidity)
R / W (5) BV 97 THERMO_CONTROL n/a n/a n/a Thermostat Only Control Enable
R / W (5) BV 67 FAN_HEAT n/a n/a n/a Turn OFF Continuous Fan when
Starting Heat Enabled (0=Continuous
Fan ON)
R / W (2) AV 2 UNOC_COOL_SP 85 46 99 Un-Occupied Cooling Setpoint
R / W (2) AV 51 UNOC_HEAT_SP 60 45 98 Un-Occupied Heating Setpoint
R / W (2) AV 75 UNOC_OVR_TP 60 0 240 Unoccupied Override Time Period
R (5) BI 103 VAV_INTELLI_2_PRES n/a n/a n/a VAV / Intelli-Comfort 2 Expansion Board
Present
R / W (2) AV 65 VAV_CL_LO_SP 55 40 69 VAV Cooling Supply Air Temperature:
Lower Setpoint (degrees F)
R / W (2) AV 66 VAV_SAT_RSET 72 40 85 VAV Cooling Supply Air Temperature:
Reset Setpoint (Space
Temperature)(degrees F)
R / W (2) AV 64 VAV_CL_HI_SP 60 41 70 VAV Cooling Supply Air Temperature:
Upper Setpoint (degrees F)
R / W (5) BV 5 VAV_OCC_HEAT n/a n/a n/a VAV Occupied Heating Enabled
R / W (2) AV 60 VAV_OHEAT_SP 68 40 85 VAV Occupied Heating Setpoint
(degrees F)
R / W (5) BV 96 VAV_UNOCC_HEAT n/a n/a n/a VAV Unoccupied Heating Enabled
TABLE 2: POINTS LIST IN DESCRIPTION ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
12 Johnson Controls Unitary Products
TABLE 3: POINTS LIST IN OBJECT ORDER
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description
R / W (2) AV 1 OCC_COOL_SP 72 46 99 Occupied Cooling Setpoint
R / W (2) AV 2 UNOC_COOL_SP 85 46 99 Un-Occupied Cooling Setpoint
R / W (2) AV 3 SAT_COOL_SP 50 40 65 Supply Air Temperature Limit for
Cooling Setpoint (degrees F)
R (2) AI 4 SUP_AIR_TEMP n/a n/a n/a Supply Air Temperature
R (2) AI 5 RET_AIR_TEMP n/a n/a n/a Return Air Temperature
R / W (2) AV 6 SPACE_TEMP n/a n/a n/a Space (Indoor) Air Temperature
R / W (2) AV 7 AMB_TEMP n/a n/a n/a Outside Air Temperature
R / W (2) AV 8 IAQ_VALUE n/a 0 5000 Demand Ventilation (IAQ) Value (PPM)
R (2) AI 9 OAQ_VALUE n/a 0 5000 Outside Demand Ventilation (OAQ)
Value (PPM)
R / W (2) AV 10 AMB_AIR_HUM n/a n/a n/a Outside Air Humidity
R (2) AI 11 AMB_AIR_ENTH n/a n/a n/a Outside Air Enthalpy
R / W (2) AV 12 RET_AIR_HUM n/a n/a n/a Return Air Humidity
R (2) AI 13 RET_AIR_ENTH n/a n/a n/a Return Air Enthalpy
R / W (2) AV 14 ACC_OVER_TME n/a n/a n/a Accumulated Unoccupied Override
Time (in hours)
R (2) AI 15 ACTIVE_ALARM n/a n/a n/a Active Alarm
R (2) AI 16 NUMBER_COMPS 2 4 Number of Compressors Available
R (2) AI 17 OP_COOL_STPT n/a n/a n/a Operating Cooling Setpoint
R / W (2) AV 18 DEMVENT_STPT 1000 0 5000 Demand Ventilation Setpoint
R / W (2) AV 19 ECON_MIN_POS 20 0 100 Economizer Minimum Position
R / W (2) AV 20 ECO_1ST_STPT 55 40 65 Economizer First Stage Setpoint
R / W (2) AV 21 ECO_2ND_STPT 50 40 65 Economizer Second Stage Setpoint
R / W (2) AV 22 ECON_OAEN_SP 27 10 50 Economizer Outside Air Enthalpy
Setpoint
R / W (2) AV 23 ECON_OAT_ENA 55 40 80 Economizer Outside Air Temperature
Enable Setpoint
R / W (2) AV 24 COM_V_HI_SP 80 65 85 Comfort Ventilation Upper Setpoint
(degrees F)
R / W (2) AV 25 COM_V_LOW_SP 70 60 80 Comfort Ventilation LowerSetpoint
(degrees F)
R / W (2) AV 26 TEM_HUM_STPT 50 20 80 Temperature / Humidity Setpoint
(percent Humidity)
R / W (2) AV 27 HGR_HUM_STPT 50 0 100 Hot Gas Reheat Humidity Setpoint
(percent Humidity)
R / W (2) AV 28 MAX_TH_OFSET 3 0 5 Max Temperature / Humidity Setpoint
Offset

1031990-UAD-A-0313
Johnson Controls Unitary Products 13
R / W (2) AV 29 TH_OFFSET 5 1 10 Temperature / Humidity % Humidity
that = 1°F of Offset
R / W (2) AV 30 MAX_DMV_ECON 50 0 100 Maximum Demand Ventillation
Economizer Position
R (2) AI 31 ECO_DAMP_OUT n/a n/a n/a Economizer Damper Output Status (0-
100%)
R (2) AI 32 EXH_DAMP_OUT n/a n/a n/a Exhaust Damper Output Status (0-
100%)
R (2) AI 33 BLDG_STATIC n/a n/a n/a Building Static Pressure
R (2) AI 34 SFAN_VFD_OUT n/a n/a n/a Supply Fan VFD Output Status (0-
100%)
R (2) AI 35 DUCT_STATIC n/a n/a n/a Duct Static Pressure
R (2) AI 36 ALARM_1 n/a n/a n/a System Alarm #1
R (2) AI 37 ALARM_2 n/a n/a n/a System Alarm #2
R (2) AI 38 ALARM_3 n/a n/a n/a System Alarm #3
R (2) AI 39 ALARM_4 n/a n/a n/a System Alarm #4
R (2) AI 40 ALARM_5 n/a n/a n/a System Alarm #5
R (2) AI 41 E_C1_ACM_HRS n/a n/a n/a Elite Compressor #1 Accumulated Run
Time (in hours)
R (2) AI 42 E_C2_ACM_HRS n/a n/a n/a Elite Compressor #2 Accumulated Run
Time (in hours)
R (2) AI 43 E_C3_ACM_HRS n/a n/a n/a Elite Compressor #3 Accumulated Run
Time (in hours)
R (2) AI 44 E_C4_ACM_HRS n/a n/a n/a Elite Compressor #4 Accumulated Run
Time (in hours)
R (2) AI 45 I_C1_ACM_HRS n/a n/a n/a Intelli-Comfort Compressor #1
Accumulated Run Time (in hours)
R (2) AI 46 I_C2_ACM_HRS n/a n/a n/a Intelli-Comfort Compressor #2
Accumulated Run Time (in hours)
R (2) AI 47 HGR_VLV_OUT n/a n/a n/a Hot Gas Reheat Valve Output Status
(0-100%)
R (2) AI 48 NUMBER_HEAT n/a n/a n/a Number of Heat Stages Available (0,0,
0 stage, 0,1= 1 stage, 1,0= 2 stage,
1,1= 3 stage)
R (2) AI 49 OP_HEAT_STPT 68 45 99 Operating Heating Setpoint
R / W (2) AV 50 OCC_HEAT_SP 68 45 98 Occupied Heating Setpoint
R / W (2) AV 51 UNOC_HEAT_SP 60 45 98 Un-Occupied Heating Setpoint
R / W (2) AV 52 SAT_HEAT_SP 135 100 180 Supply Air Temperature Limit for
Heating Setpoint (degrees F)
R / W (2) AV 53 SAT_ALM_HEAT 0 0 120 Supply Air Temperature Alarm
Setpoint for Heating
TABLE 3: POINTS LIST IN OBJECT ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
14 Johnson Controls Unitary Products
R / W (2) AV 54 OAT_HEAT_L_O 75 0 100 Outdoor Air Temperature
HeatingLockout Temperature
R(2) AI 55 HW_VLV_OUT n/a n/a n/a Hot Water Valve Output Status (0-
100%)
R(2) AI 56 CV_VAV_SELEC n/a n/a n/a CV / VAV Selected (0= Valid CV,
1=Valid VAV, 2= Invalid Value)
R / W (2) AV 57 BLDG_SP_STPT 0.15 -0.25 0.25 Building Static Pressure Setpoint
R / W (2) AV 58 DUCT_SP_STPT 1.5 0 5 Duct Static Pressure Setpoint
R / W (2) AV 59 DUCT_SD_STPT 4.5 0 5 Duct Static Pressure Shutdown
Setpoint
R / W (2) AV 60 VAV_OHEAT_SP 68 40 85 VAV Occupied Heating Setpoint
(degrees F)
R / W (2) AV 61 MWU_RAT_STPT 70 50 85 Morning Warm-Up and VAV Heating:
Return Air Temperature Setpoint
(degrees F)
R / W (2) AV 62 HYD_S1_SA_SP 120 80 180 Hydronic Heating Stage #1 Supply Air
Setpoint (degrees F)
R / W (2) AV 63 HYD_S2_SA_SP 150 81 180 Hydronic Heating Stage #2 Supply Air
Setpoint (degrees F)
R / W (2) AV 64 VAV_CL_HI_SP 60 41 70 VAV Cooling Supply Air Temperature:
Upper Setpoint (degrees F)
R / W (2) AV 65 VAV_CL_LO_SP 55 40 69 VAV Cooling Supply Air Temperature:
Lower Setpoint (degrees F)
R / W (2) AV 66 VAV_SAT_RSET 72 40 85 VAV Cooling Supply Air Temperature:
Reset Setpoint (Space
Temperature)(degrees F)
R(2) AI 67 REVISION n/a n/a xx Device Revision
R / W (2) AV 69 OP_STPT_DIF 1 1 5 Operating Setpoint Differential
R / W (2) AV 70 SAT_ALM_COOL 0 0 80 Supply Air Temperature Alarm
Setpoint for Cooling
R / W (2) AV 71 SPCE_ALM_TMP 0 0 25 Space Sensor Alarm Temperature
(degrees F, 0 = disabled)
R / W (2) AV 72 SPCE_ALM_TIM 0 0 120 Space Sensor Alarm Time (minutes F,
0 = disabled)
R / W (2) AV 73 SP_OFF_RANGE 3 0 5 Space Temprature Sensor Offset
Range (0-5 degrees)
R / W (2) AV 74 OAT_COOL_L_O 45 0 100 Outdoor Air Temperature Cooling
Lockout Temperature
R / W (2) AV 75 UNOC_OVR_TP 60 0 240 Unoccupied Override Time Period
R(2) AI 76 H1_ACCUM_HRS n/a n/a n/a Heating #1 Accumulated Run Time (in
hours)
TABLE 3: POINTS LIST IN OBJECT ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
Johnson Controls Unitary Products 15
R(2) AI 77 H2_ACCUM_HRS n/a n/a n/a Heating #2 Accumulated Run Time (in
hours)
R(2) AI 78 H3_ACCUM_HRS n/a n/a n/a Heating #3 Accumulated Run Time (in
hours)
R / W (2) AV 79 OAQ_STPT 1000 0 5000 Air Quality Setpoint Outside
R / W (2) AV 80 IO_DVNT_STPT 700 0 2000 Indoor / Outdoor Demand Ventilation
Setpoint
R / W (2) AV 81 POP_HOURS 4 0 23 Pre-Occupancy Purge Time (hours)
R / W (2) AV 82 POP_MINUTES 0 0 59 Pre-Occupancy Purge Time (minutes)
R / W (2) AV 84 ECON_RAEN_SP 27 10 50 Economizer Return Air Enthalpy
Setpoint
R / W (2) AV 85 MIN_AMB_TEMP_SP 0 0 100% Minimum Outdoor Air Temperature
Setpoint (0-100%)
R(2) AI 86 AIR_MON_INPUT 0 0 10 Air Monitor Station Input
R / W (2) AV 87 ECON_MIN_POS_LP 25 0 100 Econ Minimum Position For Low
Speed Fan
R / W (2) AV 88 LOW_AMB_ECON_STP
T0 0 60 LowAmbientEconomizerTemperature Setpoint (0 disables)
R / W (2) AV 89 LOW_AMB_ECON_MIN 0 0 99 Low Ambient Economizer Minimum
Position (Percent) (0 disables)
R / W (2) AV 90 FAN_SPD_NO_HEAT_C
OOL 50 0 100 Fan Speed: No Heating No Cooling
R / W (2) AV 91 FAN_SPD_1ST_COOL 70 0 100 Fan Speed: 1st Stage Cooling
R / W (2) AV 92 FAN_SPD_1ST_HEAT 100 0 100 Fan Speed: 1st Stage Heating
R / W (2) AV 93 FAN_SPD_ALL_COOL 100 0 100 Fan Speed: All Stages Cooling
R / W (2) AV 94 FAN_SPD_ALL_HEAT 100 0 100 Fan Speed: All Stages Heating
R / W (5) BV 1 OCCUPIED_ENA n/a n/a n/a Occupied Input Enabled
R / W (5) BV 2 HYDRONC_HEAT n/a n/a n/a Hydronic Heat Enabled
R / W (5) BV 3 HH_REVER_VLV n/a n/a n/a HydronicHeat ReverseActuated Valve
Installed
R (5) BI 4 REM_CONT_ENA n/a n/a n/a Remote Control Enabled
R / W (5) BV 5 VAV_OCC_HEAT n/a n/a n/a VAV Occupied Heating Enabled
R / W (5) BV 6 MORN_WARM-UP n/a n/a n/a Morning Warm-Up Enabled
R / W (5) BV 7 ECONO_INST n/a n/a n/a Economizer Installed
R / W (5) BV 8 PWR_EX_INST n/a n/a n/a Power Exhaust Installed
R / W (5) BV 9 MOD_EX_INST n/a n/a n/a Modulating Exhaust Installed
R / W (5) BV 10 EX_VFD_INST n/a n/a n/a Exhaust VFD Installed
R (5) BI 11 MODBUS_ALARM n/a n/a n/a Modbus Communication Alarm
TABLE 3: POINTS LIST IN OBJECT ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
16 Johnson Controls Unitary Products
R / W (5) BV 12 REDLINE n/a n/a n/a Redline (0=clear redline, 1=set redline
operation)
R / W (5) BV 13 LOADSHED n/a n/a n/a Loadshed (0=clear loadshed, 1=set
loadshed operation)
R (5) BI 14 LOW_SUP_VOLT n/a n/a n/a Low Supply Voltage (0=comps not
overridden by LSV, 1=comps
overridden)
R (5) BI 15 DIRT_FILT_SW n/a n/a n/a Dirty Filter Switch Status
(0=open,1=closed / fault)
R (5) BI 16 AIR_PROOF_SW n/a n/a n/a Air Proving Switch Status (1=closed,
0=open / no air flow)
R (5) BI 17 PURGE_SWITCH n/a n/a n/a Purge Switch Status
(0=open,1=closed)
R (5) BI 18 HGR_STAT n/a n/a n/a Hot Gas Reheat Output Status
(0=output is OFF, 1=output is ON)
R / W (5) BV 19 LOW_AMB_OVRD n/a n/a n/a Low Ambient Temperature (0=comps
not overridden by LAT, 1=comps
overridden)
R / W (5) BV 20 POP_ENABLED n/a n/a n/a Pre-Occupancy Purge Enabled
R / W (5) BV 21 FAN_ON_W_SEN n/a n/a n/a CV-Indoor Fan Operates with Space
Sensor Present Option Enabled
R / W (5) BV 22 SAT_COOLING n/a n/a n/a Supply Air Temperature Limit for
Cooling Enabled
R / W (5) BV 23 COOLING_ENA n/a n/a n/a Cooling Mode Enabled
R / W (5) BV 24 SAT_HEATING n/a n/a n/a Supply Air Temperature Limit for
Heating Enabled
R / W (5) BV 25 HEATING_ENA n/a n/a n/a Heating Mode Enabled
R / W (5) BV 26 SEN_FAULT_EN n/a n/a n/a Space Sensor Fault Override
(Construction Mode) Enabled
R / W (5) BV 28 INTELLI-STRT n/a n/a n/a Intelli-Start Enabled
R / W (5) BV 29 BP_SENS_INST n/a n/a n/a Building Static Pressure Sensor
Installed
R (5) BI 30 EX_FAN_STAT n/a n/a n/a Exhaust Fan Output Status (0=output
is OFF, 1=output is ON)
R (5) BI 31 ECONO_STATUS n/a n/a n/a Economizer Output Status (0=not Free
Cooling, 1= Free Cooling)
R (5) BI 32 FRECOOL_STAT n/a n/a n/a Free Cooling Mode Status (0=comps
not overridden by Econo, 1=comps
overridden)
R (5) BI 33 COM_VENT_STA n/a n/a n/a Comfort Ventilation Mode Status
(1=control is in Comfort Vent mode, 0=
it is not)
TABLE 3: POINTS LIST IN OBJECT ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
Johnson Controls Unitary Products 17
R / W (5) BV 34 CVM_COOLING n/a n/a n/a Comfort Ventilation Mode for Cooling
Enabled
R / W (5) BV 35 CVM_HEATING n/a n/a n/a Comfort Ventilation Mode for Heating
Enabled
R / W (5) BV 36 ECO_L_TO_SAT n/a n/a n/a Economizer Loading to Control Supply
Air Temperature Enabled
R / W (5) BV 37 OAH_SENSOR n/a n/a n/a Outside Air Humidity Sensor Enabled
R / W (5) BV 38 RAH_SENSOR n/a n/a n/a Return/Inside Air Humidity Sensor
Enabled
R / W (5) BV 39 DEMAND_VENT n/a n/a n/a Demand Ventilation (using Inside
Sensor) Enabled
R (5) BI 40 E_IFAN_STAT n/a n/a n/a Elite Indoor Fan Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 41 E_FAN_ OVER n/a n/a n/a Elite Fan Overload Switch Input Status
(1=closed, 0=open / fault)
R (5) BI 42 E_COMP1_STAT n/a n/a n/a Elite Compressor #1 Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 43 E_LPS1 n/a n/a n/a Elite Low Pressure Switch for
Compressor#1 Input Status(1=closed,
0=open / fault)
R (5) BI 44 E_HPS1 n/a n/a n/a Elite High Pressure Switch for
Compressor#1 Input Status(1=closed,
0=open / fault)
R (5) BI 45 E_C1_OVRLOAD n/a n/a n/a Elite Compressor #1 Overload Switch
Input Status (1=closed, 0=open / fault)
R (5) BI 46 E_COMP2_STAT n/a n/a n/a Elite Compressor #2 Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 47 E_LPS2 n/a n/a n/a Elite Low Pressure Switch for
Compressor#2 Input Status(1=closed,
0=open / fault)
R (5) BI 48 E_HPS2 n/a n/a n/a Elite High Pressure Switch for
Compressor#2 Input Status(1=closed,
0=open / fault)
R (5) BI 49 E_C2_OVRLOAD n/a n/a n/a Elite Compressor #2 Overload Switch
Input Status (1=closed, 0=open / fault)
R (5) BI 50 E_CFAN1_STAT n/a n/a n/a Elite Condenser Fan #1 Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 51 E_COMP3_STAT n/a n/a n/a Elite Compressor #3 Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 52 E_LPS3 n/a n/a n/a Elite Low Pressure Switch for
Compressor#3 Input Status(1=closed,
0=open / fault)
TABLE 3: POINTS LIST IN OBJECT ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
18 Johnson Controls Unitary Products
R (5) BI 53 E_HPS3 n/a n/a n/a Elite High Pressure Switch for
Compressor#3 Input Status(1=closed,
0=open / fault)
R (5) BI 54 E_C3_OVRLOAD n/a n/a n/a Elite Compressor #3 Overload Switch
Input Status (1=closed, 0=open / fault)
R (5) BI 55 E_ COMP4_STAT n/a n/a n/a Elite Compressor #4 Output Status
(0=output is OFF, 1=output is ON)
R (5) BI 56 E_LPS4 n/a n/a n/a Elite Low Pressure Switch for
Compressor#4 Input Status(1=closed,
0=open / fault)
R (5) BI 57 E_HPS4 n/a n/a n/a Elite High Pressure Switch for
Compressor#4 Input Status(1=closed,
0=open / fault)
R (5) BI 58 E_C4_OVRLOAD n/a n/a n/a Elite Compressor #4 Overload Switch
Input Status (1=closed, 0=open / fault)
R (5) BI 59 E_CFAN2_STAT n/a n/a n/a Elite Condenser Fan #2 Output Status
Input Status (0=output is OFF,
1=output is ON)
R (5) BI 60 E_GAS_VLVE1 n/a n/a n/a Elite Gas Valve #1 Input Status
(1=energized, 0=not energized)
R (5) BI 61 E_LIMIT_ 1 n/a n/a n/a Elite Limit Switch #1 Input Status
(1=closed, 0=open / fault)
R (5) BI 62 E_GAS_VLVE2 n/a n/a n/a Elite Gas Valve #2 Input Status
(1=energized, 0=not energized)
R (5) BI 63 E_LIMIT_ 2 n/a n/a n/a Elite Limit Switch #2 Input Status
(1=closed, 0=open / fault)
R (5) BI 64 E_GAS_VLVE3 n/a n/a n/a Elite Gas Valve #3 Input Status
(1=energized, 0=not energized)
R (5) BI 65 E_LIMIT_ 3 n/a n/a n/a Elite Limit Switch #3 Input Status
(1=closed, 0=open / fault)
R (5) BI 66 E_FREEZE_ST n/a n/a n/a Hot H2O Freeze Thermostat Switch
Input Status (1=closed, 0=open / fault)
R / W (5) BV 67 FAN_HEAT n/a n/a n/a Turn OFF Continuous Fan when
Starting Heat Enabled (0=Continuous
Fan ON)
R (5) BI 68 HEAT_1_STAT n/a n/a n/a H1 Heating Output #1 Status (0=output
is OFF, 1=output is ON)
R (5) BI 69 HEAT_2_STAT n/a n/a n/a H2 Heating Output #2 Status (0=output
is OFF, 1=output is ON)
R (5) BI 70 HEAT_3_STAT n/a n/a n/a H3 Heating Output #3 Status (0=output
is OFF, 1=output is ON)
TABLE 3: POINTS LIST IN OBJECT ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
Johnson Controls Unitary Products 19
R (5) BI 71 I_IFAN_STAT n/a n/a n/a Intelli-Comfort Indoor Fan Output
Status (0=output is OFF, 1=output is
ON)
R (5) BI 72 I_FAN_OVER n/a n/a n/a Intelli-Comfort Fan Overload Switch
Input Status (0=open,1=closed)
R (5) BI 73 I_COMP1_STAT n/a n/a n/a Intelli-Comfort Compressor #1 Input
Status (0=output is OFF, 1=output is
ON)
R (5) BI 74 I_LPS1 n/a n/a n/a Intelli-Comfort Low Pressure Switch for
Compressor#1 Input Status(1=closed,
0=open / fault)
R (5) BI 75 I_HPS1 n/a n/a n/a Intelli-Comfort High Pressure Switch
for Compressor #1 Input Status
(1=closed, 0=open / fault)
R (5) BI 76 I_COMP2_STAT n/a n/a n/a Intelli-Comfort Compressor #2 Input
Status (0=output is OFF, 1=output is
ON)
R (5) BI 77 I_LPS2 n/a n/a n/a Intelli-Comfort Low Pressure Switch for
Compressor#2 Input Status(1=closed,
0=open / fault)
R (5) BI 78 I_HPS2 n/a n/a n/a Intelli-Comfort High Pressure Switch
for Compressor #2 Input Status
(1=closed, 0=open / fault)
R (5) BI 79 I_CFAN_STAT n/a n/a n/a Intelli-Comfort Condenser Fan #1 Input
Status (0=output is OFF, 1=output is
ON)
R (5) BI 80 I_GAS_VLVE1 n/a n/a n/a Intelli-Comfort Gas Valve #1 Input
Status
R (5) BI 81 I_LIMIT_1 n/a n/a n/a Intelli-Comfort Limit Switch #1 Input
Status
R (5) BI 82 I_FREEZE_1 n/a n/a n/a Intelli-Comfort Freeze Thermostat
Switch #1 Input Status
(0=open,1=closed)
R (5) BI 83 I_FREEZE_2 n/a n/a n/a Intelli-Comfort Freeze Thermostat
Switch #2 Input Status
(0=open,1=closed)
R (5) BI 85 ALARM_1_ON n/a n/a n/a Alarm Buffer #1 (0=Alarm has cleared,
1=Alarm is still active)
R (5) BI 86 ALARM_2_ON n/a n/a n/a Alarm Buffer #2 (0=Alarm has cleared,
1=Alarm is still active)
R (5) BI 87 ALARM_3_ON n/a n/a n/a Alarm Buffer #3 (0=Alarm has cleared,
1=Alarm is still active)
R (5) BI 88 ALARM_4_ON n/a n/a n/a Alarm Buffer #4 (0=Alarm has cleared,
1=Alarm is still active)
TABLE 3: POINTS LIST IN OBJECT ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description

1031990-UAD-A-0313
20 Johnson Controls Unitary Products
R (5) BI 89 ALARM_5_ON n/a n/a n/a Alarm Buffer #5 (0=Alarm has cleared,
1=Alarm is still active)
R / W (5) BV 90 DF_SW_INST n/a n/a n/a Dirty Filter Switch Installed
R / W (5) BV 93 OCC_COMS_ENA n/a n/a n/a Occupied Thermostat or
Communication Input Enabled
R / W (5) BV 96 VAV_UNOCC_HEAT n/a n/a n/a VAV Unoccupied Heating Enabled
R / W (5) BV 97 THERMO_CONTROL n/a n/a n/a Thermostat Only Control Enable
R / W (5) BV 98 DIFF_ENTH_MODE n/a n/a n/a Differential enthalpy mode enabled
R / W (5) BV 99 COMM_RH n/a n/a n/a Accept Comm Value for RH
R / W (5) BV 100 COMM_OH n/a n/a n/a Accept Comm Value for OH
R / W (5) BV 101 COMM_OAT n/a n/a n/a Accept Comm Value for OAT
R (5) BI 102 4_STG_EXP_PRES n/a n/a n/a Four Stage Expansion board Present
R (5) BI 103 VAV_INTELLI_2_PRES n/a n/a n/a VAV / Intelli-Comfort 2 Expansion
Board Present
R (5) BI 104 FREEZE_STAT_1 n/a n/a n/a Freeze Stat # 1
R (5) BI 105 FREEZE_STAT_2 n/a n/a n/a Freeze Stat # 2
R (5) BI 106 FREEZE_STAT_3 n/a n/a n/a Freeze Stat # 3
R (5) BI 107 FREEZE_STAT_4 n/a n/a n/a Freeze Stat # 4
R / W (5) BV 108 COMM_ST n/a n/a n/a Accept Comm Value for Space
Temperature
R / W (5) BV 109 COMM_IAQ n/a n/a n/a Accept Comm Value for Indoor Quality
Sensor
R / W (5) BV 110 MIN_AMB_SEN n/a n/a n/a Minimum Outdoor Air Sensor Enabled
R / W (5) BV 111 REM_CONT_BAS_ECO
Nn/a n/a n/a Remote Control Third Party BAS Economizer Enable
TABLE 3: POINTS LIST IN OBJECT ORDER (CONTINUED)
Read/
Write
BACnet
Object
Type
BACnet
Object
Inst Descriptor Default Min Max Point Description