AudioCodes Mediant 800 MSBR Assembly instructions

Hardware Installation Manual
AudioCodes Multi-Service Business Routers (MSBR)
Mediant™ 800 MSBR

MSBR Series 3 Mediant 800 MSBR
Hardware Installation Manual Contents
Table of Contents
1Introduction....................................................................................................... 11
2Unpacking the Device ...................................................................................... 13
3Physical Description ........................................................................................ 15
3.1 Physical Dimensions..............................................................................................15
3.2 Front Panel Description..........................................................................................16
3.2.1 Ports and Buttons....................................................................................................16
3.2.2 LEDs .......................................................................................................................19
3.2.2.1 LAN Interface LED...................................................................................19
3.2.2.2 Power-over-Ethernet LAN LED ...............................................................19
3.2.2.3 Wi-Fi LED ................................................................................................19
3.2.2.4 WAN LEDs...............................................................................................20
3.2.2.5 FXS LED..................................................................................................22
3.2.2.6 FXO LED .................................................................................................22
3.2.2.7 BRI LED...................................................................................................22
3.2.2.8 E1/T1 LED...............................................................................................23
3.2.2.9 STATUS LED...........................................................................................23
3.2.2.10 POWER LED...........................................................................................23
3.3 Rear Panel Description ..........................................................................................24
4Attaching the Wi-Fi Antennas.......................................................................... 27
5Mounting the Device ........................................................................................ 29
5.1 Desktop Mounting ..................................................................................................29
5.2 19-Inch Rack Mounting ..........................................................................................30
5.2.1 Using a Pre-installed Rack Shelf ............................................................................30
5.2.2 Using Mounting Brackets........................................................................................31
6Cabling the Device ........................................................................................... 33
6.1 Grounding and Surge Protection............................................................................33
6.2 Connecting to WAN................................................................................................35
6.2.1 Copper Gigabit Ethernet Cabling............................................................................35
6.2.2 Fiber-Optic Gigabit Ethernet Cabling......................................................................36
6.2.3 SHDSL WAN Cabling .............................................................................................37
6.2.4 ADSL/2+ and VDSL2 WAN Cabling .......................................................................39
6.2.5 E1/T1 WAN Cabling................................................................................................41
6.2.6 3G/3.5G Cellular WAN USB Modem Cabling.........................................................42
6.3 Connecting to LAN .................................................................................................43
6.4 Connecting PoE-Enabled Clients to LAN Ports......................................................44
6.5 Analog Interfaces ...................................................................................................45
6.5.1 Connecting FXS Interfaces.....................................................................................45
6.5.2 Connecting FXO interfaces.....................................................................................46
6.5.3 Connecting the FXS Analog Lifeline.......................................................................47
6.6 ISDN BRI Interfaces...............................................................................................48
6.6.1 Connecting to BRI Lines.........................................................................................48
6.6.2 Connecting the PSTN Fallback for BRI Lines.........................................................49
6.7 Connecting to ISDN PRI (E1/T1) Trunks................................................................50
6.8 Connecting the Serial Interface to a PC.................................................................51
6.9 Connecting a USB Storage Device........................................................................54
6.10 Connecting the OSN Server...................................................................................55

Hardware Installation Manual 4 Document #: LTRT-10229
Mediant 800 MSBR
6.11 Connecting to Power..............................................................................................57
7Maintenance...................................................................................................... 59
7.1 Replacing the Power Fuse.....................................................................................59
AApproved Laser SFPs ...................................................................................... 61
BNotice for Installing CentOS Version 4.7 on OSN Server.............................. 63

MSBR Series 5 Mediant 800 MSBR
Hardware Installation Manual Contents
List of Figures
Figure 3-1: Front Panel of Mediant 800B MSBR...................................................................................16
Figure 3-2: Front Panel of Mediant 800A MSBR...................................................................................16
Figure 3-3: Rear Panel ..........................................................................................................................24
Figure 4-1: Attaching Antennas on Rear Panel.....................................................................................27
Figure 5-1: Location for Applying Rubber Feet......................................................................................29
Figure 5-2: Mounting Brackets...............................................................................................................31
Figure 5-3: Attaching the Mounting Brackets ........................................................................................31
Figure 6-1: Earthing the Device.............................................................................................................34
Figure 6-2: Cabling the WAN Copper GbE Port....................................................................................36
Figure 6-3: Removing Protective Dust Plug ..........................................................................................37
Figure 6-4: Cabling the Fiber-Optic WAN GbE Port..............................................................................37
Figure 6-5: Cabling the SHDSL WAN Port............................................................................................38
Figure 6-6: Cabling xDSL WAN Port .....................................................................................................40
Figure 6-7: RJ-45 Connector Pinouts for E1/T1 WAN...........................................................................41
Figure 6-8: Splitter Cable for Single E1/T1 WAN Port...........................................................................41
Figure 6-9: Connecting the E1/T1 WAN Port ........................................................................................41
Figure 6-10: Plugging the 3G Cellular Modem into the USB Port.........................................................42
Figure 6-11: Cabling the LAN Ports.......................................................................................................43
Figure 6-12: RJ-11 Connector Pinouts for FXS Interface......................................................................45
Figure 6-13: Connecting FXS Interfaces ...............................................................................................45
Figure 6-14: RJ-11 Connector Pinouts for FXO Interface .....................................................................46
Figure 6-15: Connecting FXO Interfaces...............................................................................................46
Figure 6-16: RJ-11 Connector Pinouts for FXS Lifeline ........................................................................47
Figure 6-17: Cabling FXS Lifeline..........................................................................................................47
Figure 6-18: RJ-45 Connector Pinouts for BRI Ports ............................................................................48
Figure 6-19: Cabling BRI Ports..............................................................................................................48
Figure 6-20: Cabling (Ports 1 and 2) PSTN Fallback............................................................................49
Figure 6-21: RJ-48c Connector Pinouts for E1/T1 ................................................................................50
Figure 6-22: Cabling E1/T1 Ports..........................................................................................................50
Figure 6-23: RS-232 Cable Adapter......................................................................................................51
Figure 6-24: Orderable RS-232 Cable Adapter.....................................................................................52
Figure 6-25: Cabling Serial Interface (RJ-45) on Mediant 800B MSBR................................................53
Figure 6-26: Cabling Serial Interface (12-pin female LX40-12P Hirose) on Mediant 800 MSBR..........53
Figure 6-27: Connecting USB Storage Device......................................................................................54
Figure 6-28: Cabling OSN Server Ports ................................................................................................56
Figure 6-29: Connecting to the Power Supply.......................................................................................57
Figure 7-1: Opening the Fuse Cavity.....................................................................................................59
Figure 7-2: Removing the Power Fuse..................................................................................................59

Hardware Installation Manual 6 Document #: LTRT-10229
Mediant 800 MSBR
List of Tables
Table 3-1: Physical Dimensions ............................................................................................................15
Table 3-2: Front-Panel Description of Ports and Buttons......................................................................16
Table 3-3: LAN LED Description............................................................................................................19
Table 3-4: PoE LAN LED Description....................................................................................................19
Table 3-5: Wi-Fi LED Description..........................................................................................................19
Table 3-6: GE WAN LED Description....................................................................................................20
Table 3-7: E1/T1 WAN LED Description................................................................................................20
Table 3-8: SHDSL WAN LED Description.............................................................................................20
Table 3-9: A/VDSL WAN LED Description ............................................................................................21
Table 3-10: WAN SFP LED Description................................................................................................21
Table 3-11: FXS LED Description..........................................................................................................22
Table 3-12: FXO LED Description.........................................................................................................22
Table 3-13: BRI LED Description...........................................................................................................22
Table 3-14: E1/T1 LED Description.......................................................................................................23
Table 3-15: STATUS LED Description ..................................................................................................23
Table 3-16: POWER LED Description...................................................................................................23
Table 3-17: Rear Panel Description.......................................................................................................24
Table 6-1: RJ-45 Connector Pinouts for Copper GbE WAN .................................................................35
Table 6-2: RJ-11 Connector Pinouts for SHDSL...................................................................................38
Table 6-3: RJ-11 Connector Pinouts for xDSL......................................................................................39
Table 6-4: RJ-45 Connector Pinouts for xDSL......................................................................................40
Table 6-5: RJ-45 Connector Pinouts for GbE/FE with PoE...................................................................43
Table 6-6: RJ-45 to DB-9 Serial Cable Connector Pinouts ...................................................................51
Table 6-7: OSN Server Platforms..........................................................................................................55
Table 7-1: Allowed Fuses for the Device...............................................................................................59
Table A-1: Approved SFP Modules.......................................................................................................61

MSBR Series 7 Mediant 800 MSBR
Hardware Installation Manual Notices
Notice
Information contained in this document is believed to be accurate and reliable at the time of
printing. However, due to ongoing product improvements and revisions, AudioCodes cannot
guarantee accuracy of printed material after the Date Published nor can it accept responsibility
for errors or omissions. Updates to this document and other documents as well as software
files can be downloaded from https://www.audiocodes.com/library/technical-documents.
This document is subject to change without notice.
Date Published: December-25-2017
WEEE EU Directive
Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed
of with unsorted waste. Please contact your local recycling authority for disposal of this
product.
Customer Support
Customer technical support and services are provided by AudioCodes or by an authorized
AudioCodes Service Partner. For more information on how to buy technical support for
AudioCodes products and for contact information, please visit our Web site at
https://www.audiocodes.com/services-support/maintenance-and-support.
Abbreviations and Terminology
Each abbreviation, unless widely used, is spelled out in full when first used.
Throughout this manual, unless otherwise specified, the term device refers to
Mediant 800 MSBR.

Hardware Installation Manual 8 Document #: LTRT-10229
Mediant 800 MSBR
Related Documentation
Document Name
SIP Release Notes
Mediant 800 MSBR SIP User's Manual
CLI Reference Guide
Notes and Warnings
Warning: The device is an INDOOR unit and therefore, must be installed only indoors.
Note: Open source software may have been added and/or amended for this product. For
further information, please visit our website at http://audiocodes.com/support or contact
your AudioCodes sales representative.
Caution Electrical Shock
Do not open or disassemble this device. The device carries high voltage and
contact with internal components may expose you to electrical shock and bodily
harm.
Warning: The device must be installed and serviced only by qualified service personnel.
Warning: For deployment in Finland, Sweden and Norway, the device must be installed
ONLY in restricted access locations that are compliant with ETS 300253 guidelines here
equipotential bonding has been implemented.
Warning: Disconnect the device from the mains and Telephone Network Voltage (TNV)
before servicing.

MSBR Series 9 Mediant 800 MSBR
Hardware Installation Manual Notices
Document Revision Record
LTRT Description
10210 Initial document release for Version 6.8.
10220 SHDSL LEDs added.
10221 A/VDSL and SHDSL LEDs updated.
10222 E1 cabling warning statement regarding STP.
10223 Power surge protection warnings.
10224 DSL connector pinouts updated.
10225 AC power cable warning (Japanese); STATUS LED update.
10225 A/VDSL port (RJ-45) cabling.
10227 BRI/PRI cabling warning.
10228 Typo fixed re 19-inch rack mounting brackets.
10229 Logo updated;
Documentation Feedback
AudioCodes continually strives to produce high quality documentation. If you have any
comments (suggestions or errors) regarding this document, please fill out the
Documentation Feedback form on our Web site at
https://online.audiocodes.com/documentation-feedback.

Hardware Installation Manual 10 Document #: LTRT-10229
Mediant 800 MSBR
This page is intentionally left blank.

MSBR Series 11 Mediant 800 MSBR
Hardware Installation Manual 1. Introduction
1 Introduction
This document provides a hardware description of the Mediant 800 MSBR (hereafter
referred to as device) and step-by-step procedures for mounting and cabling the device.
The device provides the following interfaces:

Optional telephony interfaces:
•Single or dual E1/T1 port (over single copper wire pair)
•Up to 8 BRI ports (supporting up to 16 voice channels)
•Up to 12 FXS ports
•FXS Lifeline on FXS Port 1, maintaining PSTN connectivity upon power failure.
For the combined FXS/FXO configuration, one Lifeline is available; for the 12-FXS
configuration, up to three Lifelines are available.
•Up to 12 FXO ports

Optional LAN interfaces:
•Up to 12 Ethernet LAN ports:
♦Up to 4 RJ-45 10/100/1000Base-T (Gigabit) ports
♦Up to 8 RJ-45 10/100Base-TX (Fast Ethernet) ports
Power over Ethernet (PoE) is supported on all LAN ports, complying with IEEE
802.3af-2003 and EEE 802.3at-2003. Various power budgets are supported for
PoE on the LAN ports.
•Wireless LAN 802.11n (Wi-Fi) access point at 2.4 GHz and 5 GHz Tx / Rx,
enabling data rates of up to 300 Mbps. The Wi-Fi interface also supports
802.11b/802.11g backward compatibility, allowing interoperability of multiple
devices with different types of Wi-Fi.

Two USB ports for an optional, 3G cellular WAN modem and/or USB storage services

Integrated Gigabit Ethernet (GE) Unshielded Twisted Pair (UTP) interface port, with an
option of one or two additional WAN interfaces of the following types (factory
assembled option):
•GE UTP
•Up to 4 E1/T1 WAN
•1.25 Gbps Optical Fiber SFP form factor
•ADSL2+ / VDSL2
•SHDSL, supporting up to four wire-pairs
•1 x Ethernet copper WAN port (10/100/1000Base-T)
•3G Cellular WAN access (primary or backup) using a USB modem

RJ-45 serial interface port

Open Solutions Network (OSN) server platform for hosting third-party applications
such as an IP PBX.
Notes:
•Hardware configurations may change without notice. Currently available hardware
configurations are listed in AudioCodes Price Book. For available hardware
configurations, contact your AudioCodes sales representative.
•For configuring the different interfaces, refer to the User's Manual.

Hardware Installation Manual 12 Document #: LTRT-10229
Mediant 800 MSBR
This page is intentionally left blank.

MSBR Series 13 Mediant 800 MSBR
Hardware Installation Manual 2. Unpacking the Device
2 Unpacking the Device
Follow the procedure below for unpacking the carton in which the device was shipped.
To unpack the device:
1. Open the carton and carefully remove packing materials.
2. Remove the chassis from the carton.
3. Check that there is no equipment damage.
4. Ensure that in addition to the chassis, the package contains the following items:
•Four anti-slide bumpers for desktop installation
•Two mounting brackets for 19-inch rack mounting
•One FXS Lifeline splitter cable adapter (only for models with FXS interfaces)
•Three Wi-Fi antennas (depending on ordered model)
•One E1/T1 splitter cable adapter (RJ-45 male to two RJ-45 female shielded) for
E1/T1 WAN interface (only for devices ordered with a single E1/T1 WAN port)
•Serial cable adapter
•One AC power cable
5. Check, retain and process any documents.
If there are any damaged or missing items, notify your AudioCodes sales representative.

Hardware Installation Manual 14 Document #: LTRT-10229
Mediant 800 MSBR
This page is intentionally left blank.

MSBR Series 15 Mediant 800 MSBR
Hardware Installation Manual 3. Physical Description
3 Physical Description
This section provides a physical description of the device.
Note: The Mediant 800 chassis platform has been upgraded. This revised chassis is
referred to as Mediant 800B; the previous version is referred to as Mediant 800A. The
shipped chassis version depends on your ordered hardware configuration. For more
information, contact your AudioCodes sales representative. In addition, throughout this
manual, the Mediant 800B is used in illustrations, unless specific instructions are
necessary for the Mediant 800A chassis. In such a case, both chassis versions are
shown.
3.1 Physical Dimensions
The device's physical dimensions and weight are listed in the table below:
Table 3-1: Physical Dimensions
Physical Specification Value
Dimensions (W x D x H)32 x 34.5 cm (12.6 x 13.6 inches) x 1U
Weight 2.5 kg (5.5 lb)
Environmental Operational: 5 to 40°C (41 to 104°F)
Storage: -25 to 85°C (-13 to 185°F)
Humidity: 10 to 90% non-condensing

Hardware Installation Manual 16 Document #: LTRT-10229
Mediant 800 MSBR
3.2 Front Panel Description
The front panel provides the telephony port interfaces, various networking ports, reset
pinhole button, and LEDs.
3.2.1 Ports and Buttons
The device's front panel is shown in the figure below and described in the subsequent
table.
Figure 3-1: Front Panel of Mediant 800B MSBR
Figure 3-2: Front Panel of Mediant 800A MSBR
Notes:
•The figures above are used only as examples; the number and type of port interfaces
depends on the ordered model.
•For available hardware configurations, please contact your AudioCodes sales
representative.
Table 3-2: Front-Panel Description of Ports and Buttons
Item # Label Description
1 POWER / STATUS /
Wi-Fi LEDs indicating the status of the power, reboot/initialization, and
Wireless LAN interface. For more information, see Section 3.2.2 on
page 19.
Note: The Wi-Fi LED is available only for models ordered with Wi-Fi
functionality.

MSBR Series 17 Mediant 800 MSBR
Hardware Installation Manual 3. Physical Description
Item # Label Description
2 FXS / FXO / BRI /
Digital (Optional) Telephony port interfaces, which can include one or a
combination of the following, depending on ordered model:
•FXS port interfaces (RJ-11)
•FXO port interfaces (RJ-11)
•ISDN BRI port interfaces (RJ-45)
•E1/T1 port interfaces (RJ-48)
Note: The FXS/FXO interfaces support loop-start signalling (indoor
only).
3 // Reset pinhole button for resetting the device and optionally, for
restoring the device to factory defaults.
To restore the device to factory defaults, do the following: With a
paper clip or any other similar pointed object, press and hold down
the pinhole button for at least 12 seconds, but no longer than 25
seconds.
4 GE (Copper GbE) /
V/ADSLoPOTS /
SHDSL /
GE SFP (Optic Fiber)
/
T1E1 (T1 WAN)
(Optional) One or two additional WAN interfaces. Below is a partial
list of currently supported configurations. For a full list of supported
WAN configurations, contact your AudioCodes sales representative.
One copper GE
Two copper GEs
One SFP module (dual mode, supports 100 or 1000 Mbps)
One copper GE and SFP module
Two SFP modules
One SHDSL
Two SHDSL
One AVDSL
Two AVDSL
One SHDSL and AVDSL
One copper GE and AVDSL
One copper GE and SHDSL
One SFP and AVDSL
One SFP and SHDSL
One E1/T1 WAN
Four E1/T1 WAN, copper GE, and SFP module
5 (Optional) Wi-Fi push button to turn on or off the wireless network
signals (Wi-Fi).
Note: The Wi-Fi push button is available only for models ordered
with Wi-Fi functionality.
6 GE 0/0 Gigabit Ethernet (10/100/1000Base-T) copper WAN interface (RJ-
45), provided on all models.
7 GE Up to four Gigabit Ethernet (10/100/1000Base-T) LAN ports for
connecting IP phones, computers, or switches. These ports support
half- and full-duplex modes, auto-negotiation, and straight or
crossover cable detection.
These ports also support Power over Ethernet (PoE), complying with
the IEEE 802.3af-2003 and IEEE 802.3at standards. The ports
automatically detect the presence of IEEE 802.3 compliant devices.
The maximum wattage available per port is 15.4W for IEEE 802.3af-
2003 and 30W for IEEE 802.3at. The maximum wattage available for
all ports (GE and FE) combined is 50W or 120W (depending on

Hardware Installation Manual 18 Document #: LTRT-10229
Mediant 800 MSBR
Item # Label Description
model).
Note: PoE support is a customer ordered feature.
8 FE (Optional) Eight Fast Ethernet (10/100Base-TX) RJ-45 LAN ports for
connecting IP phones, computers, or switches. These ports support
half- and full-duplex modes, auto-negotiation, and straight or
crossover cable detection.
These ports also support PoE, complying with the IEEE 802.3af-
2003 standard. The ports automatically detect the presence of IEEE
802.3af-compliant devices. The maximum wattage available per port
is 15.4W. The maximum wattage available for all ports (GE and FE)
combined is 120W.
9 CONSOLE (Mediant
800B MSBR)
RS-232 (Mediant
800A MSBR)
RS-232 serial communication port, The port type depends on
chassis model:
Mediant 800B MSBR: RJ-45
Mediant 800A MSBR: 12-pin female LX40-12P Hirose connector
10 USB/WWAN USB port that can be used for various functionalities such as 3G-
cellular WAN modem or storage capabilities. The number of ports
depends on chassis version:
Mediant 800B MSBR: 2 USB ports
Mediant 800A MSBR: 1 USB port

MSBR Series 19 Mediant 800 MSBR
Hardware Installation Manual 3. Physical Description
3.2.2 LEDs
The front panel provides various LEDs depending on the device's hardware configuration
(e.g., the available telephony interfaces). These LEDs are described in the subsequent
subsections.
3.2.2.1 LAN Interface LED
Each LAN port provides a LED (located on its left) for indicating LAN operating status, as
described in the table below.
Table 3-3: LAN LED Description
LED
Color LED State Description
Green On Ethernet link established.
Flashing Data is being received or transmitted.
- Off No Ethernet link.
3.2.2.2 Power-over-Ethernet LAN LED
Each LAN port provides a LED (located on its right) for indicating PoE status, as described
in the table below.
Table 3-4: PoE LAN LED Description
LED
Color LED State Description
Yellow
On LAN port is transferring power (i.e., PoE is activated) to the
connected equipment (e.g. IP phone).
Fast
Flashing Overload or short circuit is detected on the port output lines - PoE is not activated.
Slow
Flashing A valid PoE load is connected to the port, but the device has insufficient power to supply the required power load - PoE is not
activated.
- Off No power load is present on the port output lines - PoE is not
activated.
3.2.2.3 Wi-Fi LED
The Wi-Fi LED indicates the Wi-Fi link status, as described in the table below.
Table 3-5: Wi-Fi LED Description
LED Color LED State Description
Green On Wi-Fi is activated.
Flashing Traffic on the wireless LAN.
- Off Wi-Fi is not configured.

Hardware Installation Manual 20 Document #: LTRT-10229
Mediant 800 MSBR
3.2.2.4 WAN LEDs
3.2.2.4.1 GE WAN LED
The WAN GE port provides a LED for indicating operating status, as described in the table
below.
Table 3-6: GE WAN LED Description
LED
Color LED State Description
Green On WAN link established.
Flashing Data is being received or transmitted.
- Off No WAN link.
- Off No power received by the device.
3.2.2.4.2 E1/T1 WAN LED
The E1/T1 WAN port provides a LED for indicating operating status, as described in the
table below.
Table 3-7: E1/T1 WAN LED Description
LED
Color LED State Description
Green On Link up.
Flashing Connection in progress.
- Off No link.
3.2.2.4.3 SHDSL WAN LED
The SHDSL WAN port provides a LED for indicating operating status, as described in the
table below.
Table 3-8: SHDSL WAN LED Description
LED
Color LED State Description
Green On At least one of the links is synchronized.
Fast
Flashing At least one of the links is initializing.
Slow
Flashing SHDSL firmware is running.
- Off No WAN link or no power received by the device.