AudioCodes Mediant 800 MSBR Assembly instructions

Hardware Installation Manual
Version 6.6
February 2013
Document #: LTRT-10208
Mediant™ 800 MSBR
Multi-Service Business Router
SIP Protocol

Version 6.6 3 February 2013
Hardware Installation Manual Contents
Table of Contents
1Introduction......................................................................................................... 9
2Unpacking the Device ...................................................................................... 11
3Physical Description ........................................................................................ 13
3.1 Physical Dimensions ..............................................................................................13
3.2 Front Panel Description..........................................................................................13
3.2.1 Ports and Buttons.................................................................................................... 13
3.2.2 LEDs ....................................................................................................................... 15
3.2.2.1 LAN Interface LED................................................................................... 15
3.2.2.2 Power-over-Ethernet LAN LED ............................................................... 15
3.2.2.3 Wi-Fi LED ................................................................................................ 16
3.2.2.4 WAN LED ................................................................................................ 16
3.2.2.5 FXS LED.................................................................................................. 16
3.2.2.6 FXO LED ................................................................................................. 17
3.2.2.7 BRI LED Description................................................................................ 17
3.2.2.8 E1/T1 LED Description ............................................................................ 17
3.2.2.9 Operational Status LED........................................................................... 18
3.2.2.10 Power LED............................................................................................... 18
3.3 Rear Panel Description ..........................................................................................19
4Attaching the Wi-Fi Antennas.......................................................................... 21
5Mounting the Device ........................................................................................ 23
5.1 Desktop Mounting ..................................................................................................23
5.2 19-Inch Rack Mounting ..........................................................................................24
5.2.1 Using a Pre-installed Rack Shelf ............................................................................ 24
5.2.2 Using Mounting Brackets ........................................................................................ 25
6Cabling the Device ........................................................................................... 27
6.1 Grounding the Device.............................................................................................27
6.2 Connecting to WAN................................................................................................28
6.2.1 Gigabit Ethernet Copper Cabling............................................................................ 28
6.2.2 SHDSL WAN Cabling ............................................................................................. 29
6.2.3 ADSL and VDSL WAN Cabling............................................................................... 30
6.2.4 3G/3.5G Cellular WAN USB Modem Cabling ......................................................... 32
6.3 Connecting to LAN .................................................................................................32
6.4 Connecting PoE-Enabled Clients to LAN Ports......................................................34
6.5 FXS Interfaces........................................................................................................35
6.5.1 Connecting to Analog Devices................................................................................ 36
6.5.2 Connecting the Analog Lifeline ............................................................................... 37
6.6 ISDN BRI Interfaces ...............................................................................................38
6.6.1 Connecting to BRI Lines ......................................................................................... 38
6.6.2 Connecting the PSTN Fallback for BRI Lines......................................................... 39
6.7 Connecting ISDN PRI (E1/T1) Trunks....................................................................40
6.8 Connecting the Serial Interface to a PC .................................................................41
6.9 Connecting a USB Storage Device ........................................................................42
6.10 Connecting the OSN Server...................................................................................43
6.11 Connecting to a Power Supply ...............................................................................44

Hardware Installation Manual 4 Document #: LTRT-10208
Mediant 800 MSBR
7Maintenance – Replacing the Power Fuse ..................................................... 45
ANotice for Installing CentOS Version 4.7 on OSN Server.............................. 47

Version 6.6 5 February 2013
Hardware Installation Manual Contents
List of Figures
Figure 3-1: Front Panel.......................................................................................................................... 13
Figure 3-2: Rear Panel .......................................................................................................................... 19
Figure 4-1: Wi-Fi Antenna...................................................................................................................... 21
Figure 4-2: Attaching Antennas on Rear Panel ..................................................................................... 21
Figure 5-1: Location for Applying Rubber Foot...................................................................................... 23
Figure 5-2: Mounting Bracket (Right)..................................................................................................... 25
Figure 5-3: Attaching the Mounting Brackets ........................................................................................ 25
Figure 6-1: Earthing the Device ............................................................................................................. 27
Figure 6-2: Connecting the WAN Port ................................................................................................... 28
Figure 6-3: Connecting the SHDSL WAN Port ...................................................................................... 29
Figure 6-4: Connecting the ADSL/VDSL WAN Port .............................................................................. 30
Figure 6-5: Plugging the 3G Cellular Modem into the USB Port ........................................................... 32
Figure 6-6: Connecting the LAN Ports................................................................................................... 33
Figure 6-7: RJ-11 Connector Pinouts for FXS Interface........................................................................ 35
Figure 6-8: Connecting FXS Interfaces ................................................................................................. 35
Figure 6-9: RJ-11 Connector Pinouts for FXO Interface ....................................................................... 36
Figure 6-10: Connecting FXO Interfaces............................................................................................... 36
Figure 6-11: RJ-11 Connector Pinouts for FXS Lifeline ........................................................................ 37
Figure 6-12: Cabling FXS Lifeline.......................................................................................................... 37
Figure 6-13: RJ-45 Connector Pinouts for BRI Ports ............................................................................ 38
Figure 6-14: Cabling BRI Ports.............................................................................................................. 38
Figure 6-15: Cabling (Ports 1 and 2) PSTN Fallback ............................................................................ 39
Figure 6-16: RJ-48c Connector Pinouts for E1/T1 ................................................................................ 40
Figure 6-17: Cabling E1/T1 Ports .......................................................................................................... 40
Figure 6-18: RS-232 Cable Adapter ...................................................................................................... 41
Figure 6-19: Cabling Serial Port ............................................................................................................ 41
Figure 6-20: Connecting USB Storage Device ...................................................................................... 42
Figure 6-21: Cabling OSN Server Ports ................................................................................................ 43
Figure 6-22: Connecting to the Power Supply....................................................................................... 44
Figure 7-1: Opening the Fuse Cavity..................................................................................................... 45
Figure 7-2: Removing the Power Fuse.................................................................................................. 45

Hardware Installation Manual 6 Document #: LTRT-10208
Mediant 800 MSBR
List of Tables
Table 3-1: Physical Dimensions ............................................................................................................ 13
Table 3-2: Front Panel Description........................................................................................................ 14
Table 3-3: LAN LED Description............................................................................................................ 15
Table 3-4: PoE LAN LED Description.................................................................................................... 15
Table 3-5: Wi-Fi LED Description .......................................................................................................... 16
Table 3-6: WAN LED Description .......................................................................................................... 16
Table 3-7: FXS LED Description............................................................................................................ 16
Table 3-8: FXO LED Description ........................................................................................................... 17
Table 3-9: BRI LED Description............................................................................................................. 17
Table 3-10: E1/T1 LED Description....................................................................................................... 17
Table 3-11: STATUS LED Description .................................................................................................. 18
Table 3-12: POWER LED Description................................................................................................... 18
Table 3-13: Rear Panel Description....................................................................................................... 20
Table 6-1: RJ-45 Connector Pinouts for Gigabit Ethernet WAN ........................................................... 28
Table 6-2: RJ-45 Connector Pinouts for SHDSL ................................................................................... 29
Table 6-3: RJ-45 Connector Pinouts for ADSL/VDSL ........................................................................... 31
Table 6-4: RJ-45 Connector Pinouts for GbE/FE with PoE................................................................... 32
Table 7-1: Allowed Fuses for the Device............................................................................................... 45

Version 6.6 7 February 2013
Hardware Installation Manual Notices
Notice
This Hardware Installation Manual describes the hardware installation of AudioCodes Mediant
800 Multi-Service Business Router (MSBR).
Information contained in this document is believed to be accurate and reliable at the time of
printing. However, due to ongoing product improvements and revisions, AudioCodes cannot
guarantee accuracy of printed material after the Date Published nor can it accept responsibility
for errors or omissions.
Before consulting this document, check the corresponding Release Notes regarding feature
preconditions and/or specific support in this release. In cases where there are discrepancies
between this document and the Release Notes, the information in the Release Notes
supersedes that in this document. Updates to this document and other documents as well as
software files can be downloaded by registered customers at
http://www.audiocodes.com/downloads.
© Copyright 2013 AudioCodes Ltd. All rights reserved.
This document is subject to change without notice.
Date Published: February-17-2013
Trademarks
AudioCodes, AC, AudioCoded, Ardito, CTI2, CTI², CTI Squared, HD VoIP, HD VoIP
Sounds Better, InTouch, IPmedia, Mediant, MediaPack, NetCoder, Netrake, Nuera, Open
Solutions Network, OSN, Stretto, TrunkPack, VMAS, VoicePacketizer, VoIPerfect,
VoIPerfectHD, What’s Inside Matters, Your Gateway To VoIP and 3GX are trademarks or
registered trademarks of AudioCodes Limited. All other products or trademarks are property
of their respective owners.
WEEE EU Directive
Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed
of with unsorted waste. Please contact your local recycling authority for disposal of this
product.
Customer Support
Customer technical support and service are generally provided by AudioCodes’
Distributors, Partners, and Resellers from whom the product was purchased. For technical
support for products purchased directly from AudioCodes, or for customers subscribed to
AudioCodes Customer Technical Support (ACTS), contact [e-mail].
Abbreviations and Terminology
Each abbreviation, unless widely used, is spelled out in full when first used.
Throughout this manual, unless otherwise specified, the term device refers to Mediant 800
MSBR.

Hardware Installation Manual 8 Document #: LTRT-10208
Mediant 800 MSBR
Related Documentation
Document Name
SIP Release Notes
Mediant 800 MSBR SIP User's Manual
MSBR Series CLI Reference Guide for Data Functionality
MSBR Series CLI Reference Guide for System and VoIP Functionalities
Notes and Warnings
Note: Open source software may have been added and/or amended for this product.
For further information, please visit our website at http://audiocodes.com/support
or contact your AudioCodes sales representative.
Caution Electrical Shock
Do not open or disassemble this device. The device carries high voltage and
contact with internal components may expose you to electrical shock and bodily
harm.
Warning:
The device must be installed and serviced only by qualified service
personnel.
Warning: The device is an indoor unit and therefore, must be installed only indoors.
Warning: For deployment in Finland, Sweden and Norway, the device must be installed
ONLY in restricted access locations that are compliant with ETS 300 253
guidelines where equipotential bonding has been implemented.
Warning: Disconnect the device from the mains and Telephone Network Voltage
(TNV) before servicing.
Documentation Feedback
AudioCodes continually strives to produce high quality documentation. If you have any
comments (suggestions or errors) regarding this document, please fill out the
Documentation Feedback form on our Web site at http://www.audiocodes.com/downloads.
Your valuable feedback is highly appreciated.

Version 6.6 9 February 2013
Hardware Installation Manual 1. Introduction
1 Introduction
This document provides a hardware description of the Mediant 800 MSBR (hereafter
referred to as device) and step-by-step procedures for cabling the device.
The device provides the following optional, customer-ordered interfaces:

Optional telephony interfaces:
•Single E1/T1 port (over double copper wire-pairs)
•Up to 8 BRI ports (supporting up to 16 voice channels)
•Up to 12 FXS ports
•Up to 12 FXO ports
•FXS Lifeline on FXS Port 1, maintaining PSTN connectivity upon power failure.
For the combined FXS/FXO configuration, one Lifeline is available; for the 12-FXS
configuration, up to three Lifelines are available.

Optional LAN interfaces:
•Up to 12 Ethernet LAN ports:
♦Up to 4 RJ-45 10/100/1000Base-T (Gigabit) ports
♦Up to 8 RJ-45 10/100Base-TX (Fast Ethernet) ports
•Wireless LAN 802.11n (Wi-Fi) access point at 2.4 GHz and 5 GHz Tx / Rx,
enabling data rates of up to 300 Mbps. The Wi-Fi interface also supports
802.11b/802.11g backward compatibility, allowing interoperability of multiple
devices with different types of Wi-Fi.

Optional WAN interface types:
•1 x Ethernet copper WAN port (10/100/1000Base-T).
•ADSL / VDSL interface (RJ-45 port):
•1 x Symmetric High-Speed Digital Subscriber Line (SHDSL) WAN port, providing
up to 4 SHDSL wire-pairs housed on a single RJ-45 connector:
•3G Cellular WAN access (primary or backup) using a USB modem.

Power over Ethernet (PoE) supported on all LAN ports, complying with IEEE 802.3af-
2003. Various power budgets (120 and 50 Watt) are supported for PoE on the LAN
ports.

OSN server platform for hosting third-party applications such as an IP PBX. The
following OSN server platforms are available (depending on configuration):
•OSN1: Intel® Atom™ 1.6 GHz processor, with 1GB or 2GB RAM (depending on
Mediant 800 model) and a single storage hard disk drive (SATA storage)
•OSN2: Intel® Celeron® 847E (2x 1.1 GHz), 2 MB L2 Cache, Intel® HM65 Second
Generation
Note: For information on configuring the device, refer to the device's User’s Manual.

Hardware Installation Manual 10 Document #: LTRT-10208
Mediant 800 MSBR
Reader's Notes

Version 6.6 11 February 2013
Hardware Installation Manual 2. Unpacking the Device
2 Unpacking the Device
Follow the procedure below for unpacking the carton in which the device is shipped.
To unpack the device:
1. Open the carton and remove packing materials.
2. Remove the chassis from the carton.
3. Check that there is no equipment damage.
4. Ensure that in addition to the chassis, the package contains the following items:
•Four anti-slide bumpers for desktop installation
•Two mounting brackets for 19-inch rack mounting
•One FXS Lifeline cable adapter (only for models with FXS interfaces)
•Three Wi-Fi antennas (depending on Mediant 800 MSBR ordered model)
•One AC power cable
5. Check, retain and process any documents.
If there are any damaged or missing items, notify your AudioCodes sales representative.

Hardware Installation Manual 12 Document #: LTRT-10208
Mediant 800 MSBR
Reader's Notes

Version 6.6 13 February 2013
Hardware Installation Manual 3. Physical Description
3 Physical Description
This section provides a physical description of the device.
3.1 Physical Dimensions
The device's physical dimensions and weight are listed in the table below:
Table 3-1: Physical Dimensions
Physical Specification Value
Dimensions (H x W x D) 32 x 34.5 cm (12.6 x 13.6 inches) x 1U
Weight 2.5 kg (5.5 lb)
3.2 Front Panel Description
The front panel provides the telephony port interfaces, various networking ports, reset
pinhole button, and LEDs.
3.2.1 Ports and Buttons
The device's front panel is shown in the figure below and described in the subsequent
table.
Figure 3-1: Front Panel
Note: The figure above is used only as an example. The number and type of port
interfaces depends on the ordered model.

Hardware Installation Manual 14 Document #: LTRT-10208
Mediant 800 MSBR
Table 3-2: Front Panel Description
Item # Label Description
1 USB/WWAN USB port for connecting an optional 3G cellular WAN modem (for
primary or backup WAN), or an external USB hard drive or flash disk
(disk on key) for USB storage capabilities.
2 RS-232 RS-232 port for serial communication.
3 POWER /
STATUS / WAN
LEDs indicating the status of the power, reboot/initialization, and WAN
interface. For more information, see Section 3.2.2 on page 15.
4 FXS / FXO / BRI /
Digital
Telephony port interfaces that can include one or a combination of the
following, depending on the ordered model:
•FXS port interfaces (RJ-11)
•FXO port interfaces (RJ-11)
•ISDN BRI port interfaces (RJ-45)
•E1/T1 port interfaces (RJ-48)
Notes:
•The FXS/FXO interfaces support loop-start signalling (indoor only).
•For supported hardware configuration options, refer to the Release
Notes.
5 -Reset pinhole button for resetting the device and optionally, for restoring
the device factory defaults. To restore the device to factory defaults, do
the following:
With a paper clip or any other similar pointed object, press and hold
down the Reset pinhole button for at least 12 seconds, but no
more than 25 seconds.
6 GE
- or -,
SHDSL
-or -
VDSL/ADSLoPO
TS
WAN interface, depending on ordered model:
WAN Ethernet RJ-45 port (10/100/1000Base-T)
Symmetric High-Speed Digital Subscriber Line (SHDSL) RJ-45 port
(4 wire pairs)
Asymmetric Digital Subscriber Line (ADSL) / Very High-speed Digital
Subscriber Line (VDSL) RJ-45 port
7 GE Up to four Gigabit Ethernet (10/100/1000Base-T) LAN ports for
connecting IP phones, computers, or switches. These ports support
half- and full-duplex modes, auto-negotiation, and straight or crossover
cable detection.
These ports also support Power over Ethernet (PoE), complying with the
IEEE 802.3af-2003 standard. The ports automatically detect the
presence of IEEE 802.3 compliant devices.
The maximum wattage available per port is 15.4W. The maximum
wattage available for all ports (GE and FE) combined is 50W or 120W
(depending on model).
Note: PoE support is a customer ordered feature.

Version 6.6 15 February 2013
Hardware Installation Manual 3. Physical Description
Item # Label Description
8 FE Eight Fast Ethernet (10/100Base-TX) RJ-45 LAN ports for connecting IP
phones, computers, or switches. These ports support half- and full-
duplex modes, auto-negotiation, and straight or crossover cable
detection.
These ports also support PoE, complying with the IEEE 802.3af-2003
standard. The ports automatically detect the presence of IEEE 802.3af-
compliant devices. The maximum wattage available per port is 15.4W.
The maximum wattage available for all ports (GE and FE) combined is
120W.
3.2.2 LEDs
The front panel provides various LEDs depending on the device's hardware configuration
(e.g., the available telephony interfaces). These LEDs are described in the subsequent
subsections.
3.2.2.1 LAN Interface LED
Each LAN port provides a LED (located on its left) for indicating LAN operating status, as
described in the table below.
Table 3-3: LAN LED Description
LED
Color
LED
State
Description
Green On Ethernet link established.
Flashing Data is being received or transmitted.
- Off No Ethernet link.
3.2.2.2 Power-over-Ethernet LAN LED
Each LAN port provides a LED (located on its right) for indicating PoE status, as described
in the table below.
Table 3-4: PoE LAN LED Description
LED
Color
LED
State
Description
Yellow
On LAN port is transferring power (i.e., PoE is activated) to the
connected equipment (e.g. IP phone).
Fast
Flashing
Overload or short circuit is detected on the port output lines - PoE
is not activated.
Slow
Flashing
A valid PoE load is connected to the port, but the device has
insufficient power to supply the required power load - PoE is not
activated.
- Off No power load is present on the port output lines - PoE is not
activated.

Hardware Installation Manual 16 Document #: LTRT-10208
Mediant 800 MSBR
3.2.2.3 Wi-Fi LED
The Wi-Fi LED indicates the Wi-Fi link status, as described in the table below.
Table 3-5: Wi-Fi LED Description
LED Color LED State Description
On Wi-Fi is activated.
Flashing Traffic on the wireless LAN.
- Off Wi-Fi is not configured.
3.2.2.4 WAN LED
The WAN port provides a LED for indicating operating status, as described in the table
below.
Table 3-6: WAN LED Description
LED
Color
LED
State
Description
Green On WAN link established.
Flashing Data is being received or transmitted.
- Off No WAN link.
- Off No power received by the device.
3.2.2.5 FXS LED
Each FXS port provides a LED for indicating operating status, as described in the table
below.
Table 3-7: FXS LED Description
LED
Color
LED
State
Description
Green On Phone is off-hooked.
Flashing Rings the extension line.
Red On Error - malfunction in line or out of service due to Serial Peripheral
Interface (SPI) failure.
- Off Phone is on hook.
- Off No power received by the device.

Version 6.6 17 February 2013
Hardware Installation Manual 3. Physical Description
3.2.2.6 FXO LED
Each FXO port provides a LED for indicating operating status, as described in the table
below.
Table 3-8: FXO LED Description
LED
Color
LED
State
Description
Green On FXO line is off-hooked toward the PBX.
Flashing Ring signal detected from the PBX.
Red On Error - malfunction in line or out of service due to Serial Peripheral
Interface (SPI) failure.
- Off Line is on hook.
- Off No power received by the device.
3.2.2.7 BRI LED Description
Each BRI port provides a LED for indicating operating status, as described in the table
below:
Table 3-9: BRI LED Description
Color State Description
Green On Physical layer (Layer 1) is synchronized (normal operation).
Red On Physical layer (Layer 1) is not synchronized.
- Off Trunk is not active.
3.2.2.8 E1/T1 LED Description
Each trunk port provides a LED for indicating operating status, as described in the table
below:
Table 3-10: E1/T1 LED Description
Color State Description
Green On Trunk is synchronized (normal operation).
Red On Loss due to any of the following signals:
LOS - Loss of Signal
LOF - Loss of Frame
AIS - Alarm Indication Signal (the Blue Alarm)
RAI - Remote Alarm Indication (the Yellow Alarm)
- Off Failure / disruption in the AC power supply or the power is
currently not being supplied to the device through the AC
power supply entry.

Hardware Installation Manual 18 Document #: LTRT-10208
Mediant 800 MSBR
3.2.2.9 Operational Status LED
The STATUS LED indicates the operating status, as described in the table below.
Table 3-11: STATUS LED Description
LED
Color
LED
State
Description
Green On The device is operational.
Flashing The device is rebooting.
Red On Boot failure.
3.2.2.10 Power LED
The POWER LED indicates the operating status, as described in the table below.
Table 3-12: POWER LED Description
LED
Color
LED
State
Description
Green On Power is received by the device.
- Off No power received by the device.

Version 6.6 19 February 2013
Hardware Installation Manual 3. Physical Description
3.3 Rear Panel Description
The device's rear panel is shown in the figure below and described in the subsequent table.
Figure 3-2: Rear Panel
Note: The figure above is used only as an example. The OSN server ports and Wi-Fi
interface are available only if customer ordered.

Hardware Installation Manual 20 Document #: LTRT-10208
Mediant 800 MSBR
Table 3-13: Rear Panel Description
Item # Label Description
1 OSN USB Three USB ports (Standard-A type) for connecting computer
peripherals (e.g., mouse and keyboard). These are used when
implementing the OSN.
Note: These ports are available only if the device is equipped with
the OSN server (customer ordered).
2 OSN VGA 15-Pin DB-type female VGA port for connecting to a monitor
(screen). This port is used when implementing the OSN.
Note: This port is available only if the device is equipped with the
OSN server (customer ordered).
3 - Reset button for resetting the OSN server.
4 GE 1
GE 2
Two 10/100/1000Base-T Ethernet ports (RJ-45) for connecting
directly to the OSN server. For example, one port can be connected
to the LAN (to IP Phones) and the second port to the WAN interface
(to an IP PBX).
5 Protective earthing screw.
6 100-240V~1.5A
50-60Hz
3-Prong AC power supply entry.
7 - Wi-Fi antennas. Wireless LAN 802.11n (Wi-Fi) access point at 2.4
GHz and 5 GHz Tx / Rx, enabling data rates of up to 300 Mbps. The
Wi-Fi interface also supports 802.11b/802.11g backward
compatibility, allowing interoperability of multiple devices with
different types of Wi-Fi.