AudioCodes Mediant 800Ci uCPE User manual

1 |P a g e
Mediant™800Ci uCPE
Quick Setup Guide
Welcome
Thank you for choosing AudioCodes’ Mediant 800Ci uCPE.
This document is intended to provide basic instructions for initial setup of the Mediant 800Ci uCPE (hereafter,
referred to as device) and connecting it to your network. For advanced configuration, please refer to the
device's Configuration Notes and Hardware Manual respectively, which can be downloaded from AudioCodes
Website at https://www.audiocodes.com/library/technical-documents.
Before you begin, please read the Safety Precautions on the next page and click here to view the Regulatory
Information document.

2 |P a g e
Safety Precautions
▪This device is an indoor unit and therefore, must not be installed outdoors.
▪Ethernet cabling must be routed only indoors and must not exit the building.
▪Do not open or dismantle the device.
▪Do not expose the device to water or moisture.
▪Make sure the device is installed in a well-ventilated location to avoid over heating of internal
components and subsequent damage.
▪Do not place any object on top of the device and make sure that sufficient clearance from the top and
sides are maintained to ensure proper airflow to avoid over heating of internal components.
▪Operate the device in an ambient temperature (Tma) that does not exceed 40°C (104°F).
▪Use only the supplied AC/DC power adapter for connection to the power source.
▪In case of a malfunction, do not attempt to fix the power adapter and do not use any other type of
power adapter.
Package Contents
Make sure that the following items (in addition to any separate-orderable items that you may have purchased)
are included with your shipped device:
▪4 x anti-slide bumpers for desktop mounting
▪1 x AC/DC power adapter
▪Regulatory Information document
▪This Quick Guide

3 |P a g e
Physical Description of Front Panel
1
PWR
LED indicating power status:
Green On
Power received by device.
Off
No power.
SYS
LED indicating operating status:
Green On
Device is operational.
Green Flashing
Initial rebooting stage or software upgrade in process.
Red On
Boot failure.
Off
Advanced rebooting stage.
4G
LED indicating 4G LTE cellular modem status:
Green On
SIM card installed and an LTE cellular connection has
been established.
Green Flashing
In the process of connecting to the cellular network.
Red On
▪No SIM card installed.
▪SIM card is installed, but cannot connect to the
cellular network (e.g., SIM failure).
Off
▪Cellular interface has been configured but has been
shut down (regardless of whether a SIM card is
installed or not).
▪Cellular interface is not configured or not licensed
based on device's License Key (regardless of whether
a SIM card is installed or not).
▪
2
SIM card slot for inserting a SIM card (mini-SIM card size) provided by your service for
4G Long-Term Evolution (LTE) cellular modem (cellular WAN).
3
CONSOLE
RJ-45 port for RS-232 serial communication with the device.
4
USB 3.0 port which can be used for storage on external USB flash disk.
6
1
3
4
5
7
8
2

4 |P a g e
5
//
Reset pinhole button for resetting the device or restoring it to factory defaults. To
restore to factory defaults: with a paper clip or any other similar pointed object, press
and hold down the button for at least 12 seconds (but no more than 25 seconds).
6
S0 / WAN
WAN Ethernet ports:
DSL: RJ-11 port for DSL WAN interface.
Green On
DSL link connected (trained) with peer ("showtime").
Green Fast-Flashing
Training up (connection in progress) and negotiating with
peer.
Green Slow Flashing
DSL port administratively up, but idle (not connected and
no peer detected).
Green Two Fast-Flashes
and then Idle Sequences
DSL port initializing itself after being enabled or upon
mode change.
Off
DSL port administratively shutdown or not configured
GE:RJ-45 port for Gigabit Ethernet WAN interface.
Green On
WAN GE link established.
Green Flashing
Data received or transmitted.
Off
No WAN GE link or power not received by the device.
SFP: SFP transceiver module for fiber optic WAN.
Green On
WAN fiber link established.
Green Flashing
Data received or transmitted.
Off
No WAN fiber link.
7
S1 / GE LAN
LED indicating Gigabit Ethernet LAN
Green On
Ethernet link established.
Green Flashing
Data received or transmitted.
Off
No Ethernet link.
8
S2 / BRI
RJ-45 ports for connecting BRI ISDN terminal equipment such as ISDN telephones or
PBXs.
Green On
Physical layer (Layer 1) is synchronized (normal
operation).
Red On
Physical layer (Layer 1) is not synchronized.
Off
Trunk is not active.

5 |P a g e
Physical Description of Rear Panel
1
-
Two cellular antennas for 4G LTE cellular connectivity.
2
USB
USB 3.0 port (Standard-A type) for connecting computer peripherals (e.g., mouse and
keyboard) to the OSN server.
3
OSN PWR
LED indicating power status of the OSN server.
4
CONSOLE
Micro USB port for connecting a monitor to the OSN server.
5
1-4
Four 10/100/1000Base-T Ethernet (RJ-45) ports for connecting directly to the OSN
server. For example, one port can be connected to the LAN (IP Phones) and another
port to the WAN interface (IP PBX).
6
Protective earthing (grounding) screw.
7
100-240V
~1A
50-60Hz
AC power plug entry.
1
2
4
5
1
6
7
3

6 |P a g e
Mounting the Device
You can mount the device in several ways:
▪Placing it on a desktop using the four anti-slide bumpers (supplied), which you need to stick on the
grooves located on the underside of the device. The bumpers avoid involuntary movement of the unit
on the desktop as well as enable better air flow for cooling the device.
▪Mounting it in a standard 19-inch rack, which involves placing the device on a pre-installed rack shelf
(not supplied) and then securing the device to the rack frame using the front-mounting brackets
(supplied).

7 |P a g e
Initial Connectivity
This section describes how to initially access the device's management interface and change its default IP
address to correspond with your networking scheme. Device management can always be done through the
LAN interface, but you can also enable device management through the WAN (as explained in the configuration
guide).
Accessing Device through Web Interface
You can access the Web-based management interface using the device's default LAN IP address:
▪IP Address: 192.168.0.1
▪Prefix Length: 24 (255.255.255.0)
▪Default Gateway: 0.0.0.0
▪VLAN ID: 1
By default, the device's embedded DHCP server is enabled for the LAN, and with default IP pool addresses
relating to the default subnet LAN. The DHCP server allocates this pool of IP addresses to computers
connected to its LAN interface. You can disable the DHCP server or modify the IP address pool.
Accessing Device through Default LAN IP Address
1. Connect the LAN Port (S1 / GE LAN) to your computer's network interface, using a straight-through
Ethernet cable:
2. Make sure that your computer is configured to automatically obtain an IP address. The device has an
embedded DHCP server, which by default, allocates IP addresses to connected computers.

8 |P a g e
3. On your computer, start a Web browser and in the URL address field, enter the device's default IP
address; the Web interface's Web Login screen appears:
4. In the 'Username' and 'Password' fields, enter the case-sensitive, default login username (Admin) and
password (Admin).
5. Click Log In.
Configuring LAN and WAN
This section describes how to configure the device's LAN and WAN interfaces.
After accessing the device through the LAN interface, you can configure Web management access from one of
the following interfaces:
◼Any of the configured Voice Gateway LAN interfaces.
◼WAN port interface: In this setup, you need to enable remote access to the WAN port interface.
For basic configuration, click here to view the configuration note.
Modifying LAN Interface
The device's default LAN IP address is 192.168.0.1/24. You can change this to suit your networking scheme.
By default, the device's embedded DHCP server is enabled for the LAN, and with default IP pool addresses
relating to the default subnet LAN. You can disable the DHCP server or modify the IP address pool. The
DHCP server allocates this pool of IP addresses to the computers connected to its LAN interface.
1. Open the LAN Interface page (Setup menu > IP NETWORK tab > CORE ENTITIES folder > LAN Interface).
2. Configure the following:
▪LAN Interfaces
▪DHCP (enable / disable)
▪DNS

9 |P a g e
Configuring WAN Interface
This section describes how to configure the WAN interface, which uses Gigabit Ethernet.
Before configuring the WAN interface, make sure that you have all the required information from your Internet
service provider.
1. Connect the WAN port to the WAN network. For information on cabling the WAN port, refer to the
Hardware Installation Manual.
2. Open the WAN Interface page (Setup menu > IP NETWORK tab > CORE ENTITIES folder > WAN
Interface).
3. Configure the following:
▪WAN settings (Static or DHCP Client - default is DHCP Client)
▪DNS settings (Static or Auto - default is Auto)

10 |P a g e
Cabling the Device
1. Insert the SIM card (provided by your Service Provider) into the SIM slot.
2. Connect the device's WAN port interface to your router.
3. Connect the device's Gigabit Ethernet ports to your LAN network.

11 |P a g e
4. Connect the device's BRI ports to BRI phones or the ISDN network.
5. Ground (earth) the device, using the grounding screw on the rear panel.
6. Connect the device to your AC electrical outlet, using the power outlet on the rear panel.
Connecting to OSN Server
The following procedure describes how to access the device's embedded OSN server so that you can install
your applications (e.g., SD-WAN).
1. Establish a serial connection with the OSN server:
a. Connect your computer's COM port to the device's Micro USB port (labeled CONSOLE) located on
the rear panel.
b. Using a terminal emulator program (e.g., PuTTY), connect to the OSN server using the following
settings:
•Serial Line: <COM port –check your computer's Device Manager for assigned COM>
•Speed: 115200 bps
•Connection Type: Serial
2. Attach your bootable USB dongle to the device's USB port (labeled USB) located on the rear panel, and
then power up the device. By default, the server boots from the USB as first boot priority.

12 |P a g e
©2022 AudioCodes Ltd. All rights reserved. AudioCodes, AC, HD VoIP, HD VoIP Sounds Better, IPmedia, Mediant,
MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your
Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice, AudioCodes Meeting Insights, AudioCodes Room Experience
and CloudBond are trademarks or registered trademarks of AudioCodes Limited. All other products or trademarks are
property of their respective owners. Product specifications are subject to change without notice.
International Headquarters
1 Hayarden Street,
Airport City
Lod 7019900, Israel
Tel: [phone]
Fax: [phone]
AudioCodes Inc.
200 Cottontail Lane,
Suite A101E,
Somerset, NJ 08873
Tel: [phone]
Fax: [phone]
Contact us: https://www.audiocodes.com/corporate/offices-worldwide
Website: https://www.audiocodes.com
Document #: LTRT-23620
Date Published: 3/5/2022