Audiovox UltraGuard UG-OE3 Operating instructions

Model UG-OE3
TRANSMITTER PROGRAMMING GUIDE
The transmitters included with the security system have been pre-
pro grammed at the factory, with each button pre-assigned to control a specific
function of the security system. Although the security system in the vehicle has
eithera3or4channel receiver, depending on the model, the transmitters
included with the system are capable of transmitting 7 distinct signals. This
allows you to program each transmitter to more than one vehicle in two car
families, and also allows you to change which button(s) control certain functions
of the system.
( Example: Transmitter channel 5 can be programmed to activate Receiver
channel 2.) Refer to the chart below for access to each of the transmitter
channels, and for the standard factory button assignments.
TRANSMITTER SYSTEM RECEIVER
CHANNEL BUTTONS CHANNEL FUNCTION
1 1 **Remote Arm & Disarm
**Remote Emergency Panic
Remote Door Lock & Unlock
2 2 * Pulsed Output for Accessories
3 3 * Switched Output for Accessories
4 * Switched Output for Accessories
4
5
6
7

2
Some of the more common accessories for these additional channels are;
*AS 9554 Remote Garage Door Interface
*AS 9075 Remote car starter
*AS 9153 Remote window roll up
*AS 9256 Remote trunk release relay
** Only Available With Remote Alarm Systems
In addition to the information provided above, the UG-OE3 transmitter is
capable of utilizing different transmitter Icon pads. These replacement pads may
be used with your transmitter, depending on the specific options that may have
been installed or added to your security/keyless entry system. (If your transmitter
appears more like one of the units shown on page 4 of this manual, use the
text reference along side the specific transmitter for programming your unit).
PROGRAMMING THE TRANSMITTERS
It is important to remember that during programming, each individual step of the
procedure must be executed within 15 seconds of the previous step.
When the 15 second time limit is allowed to expire, the system will automatically
terminate the programming mode. This is indicated by a long chirp from the
siren.
Additionally, the system will store codes from up to four different transmitters.
If a 5th transmitter is programmed to any receiver channel, then the first transmitter
programmed to that channel will be erased from the system's memory.
To Program replacement or additional transmitters:
1. Enter the vehicle, and turn the ignition key to the " on " position.
2. Flip the valet switch "on" - "off" - "on" - "off" - "on" - then "off".
3. The dash L.E.D. will flash one time, and the sounding device will beep one
time, indicating the system is ready to accept programming for receiver
channel 1.
4. Press and hold the Lock,Arm / Unlock, Disarm button for 4 seconds or until
the sounding device emits a long beep, indicating the signal has been
stored into memory.
5. If you have additional transmitters ( up to 4 ) that need to be programmed,
repeat step 4 for each transmitter.
6. Flip the valet switch "on" then "off".
7. The dash L.E.D. will flash two times, and the sounding device will beep two
times, indicating the system is ready to accept programming for receiver
channel 2.
8. Press and hold the Trunk for 4 seconds or until the sounding device emits
a long beep, indicating the signal has been stored into memory.
9. If you have additional transmitters ( up to 4 ) that need to be programmed,
repeat step 8 for each transmitter.

10. Flip the valet switch "on" then "off".
11. The dash L.E.D. will flash three times, and the sounding device will beep
three times, indicating the system is ready to accept programming for
receiver channel 3.
12. Press and hold the selected Option button for 4 seconds or until the
sounding device emits a long beep, indicating the signal has been stored
into memory.
13. If you have additional transmitters ( up to 4 ) that need to be programmed,
repeat step 12 for each transmitter.
14. Flip the valet switch on then off.
15. The dash L.E.D. will flash four times, and the sounding device will beep four
times, indicating the system is ready to accept programming for receiver
channel 4.
16. Press and hold the combination of any two buttons for 4 seconds or until the
sounding device emits a long beep, indicating the signal has been stored
into memory.
17. If you have additional transmitters ( up to 4 ) that need to be programmed,
repeat step 16 for each transmitter.
18. Turn the ignition key off. The sounding device will emit one short beep
followed by one long beep indicating the system has terminated the
program mode.
TRANSMITTER BATTERY REPLACEMENT
You will notice a decrease in transmitter range as the battery condition
deteriorates. Transmitter battery replacement is recommended at least every
10 to 12 months, depending upon how frequently the transmitter is used.
The transmitter has a small red L.E.D. built into the case. This L.E.D. can be
used to indicate battery condition. If the L.E.D.
does not illuminate, then the battery is discharged,
and must be replaced.
To replace the transmitter battery :
1. Remove the small phillips head screws from
the bottom cover of the transmitter.
2. Carefully unsnap the top cover of the
transmitter from the bottom cover.
3. Remove the discharged battery, making note
of the location of the + and - contacts, and
replace with a new type GP 27A 12 volt battery.
4. Replace the transmitter cover, taking care not to damage the L.E.D. or
switches on the circuit board, and secure with the small phillips head screw.
3

ORDER FORM FOR 3 BUTTON TRANSMITTER
MODEL NO. UG OE3
IMPORTANT : To help us expedite your order, please print all of the
information legibly, and mail this form and your payment according to the
instructions below.
1. Name : ____________________________________________________
Address : _____________________________________________________
City : _____________________ State : _______ Zip Code : ____________
2. Telephone Number : ( _______ ) _________________________________
3. Enter the total number of transmitters required here : ________________
4. List model number of your actual transmitter pad as shown on page
4 of this manual:
5. The cost per transmitter is $ 65.00.
6. Enter the total amount enclosed here : ____________________________
( New York state residents must include the appropriate sales tax.)
7. Method of payment; check one of the boxes below.
Mastercard Visa Check or money order*(donotsend cash )
* Make checks payable to UltraGuard Security Systems
8. Credit Card Number : ________________________________________
9. Credit Card Expiration Date : _____________________
Credit card purchasers can order additional or replacement
transmitters by phone. Simply dial 1-818-902-0393
10. Mail this form and your check, to ;
UltraGuard Security Systems
15600 Roscoe Blvd., #9 Van Nuys, CA 91406
Attn: Transmitter Ordering Department
