Audiovox PRO94BT2 Operating instructions

128-4618
sht. 1 of 4
Button 1
Button 2
BothButtons
BUTTON CHANNEL SYSTEM FUNCTION
Factory Settings for Transmitter Buttons
Thetransmitters includedin thesecurity systemkit arepre-programmed atthe
factory, with button assignments (channels) prioritized in a standard format.
Referto the chartfor standardfactory configuration.
RemoteArm/Disarm
Remote Emergency Panic
Door Lock/Unlock (Optional)
PulsedOutput
*(Optional Devices)
SwitchedOutput
* (Optional Devices)
1
2
3
* Some of the more common accessories for these channels are;
Remote Car Starter
Remote Trunk Release Relay
Remote Garage Door Interface
Remote Window Roll Up
AS 9151
AS 9256
AS 9154
AS 9153
TRANSMITTER PROGRAMMING GUIDE
Model: PRO 94 BT2
Released 7-10-95.

128-4618
sht. 2 of 4
Thesefactoryprogrammed settingscan beprioritized based onan individual's
frequencyofuse,(i.e.pressingbothbuttonssimultaneouslytoactivatechannel
1,arm/disarmetc.) byfollowingthe normalprogramminginstructionsbelow.
Please note when changing the button sequences of the factory settings, it is
necessarytoperformsteps5,9,and12threetimesusing"transmitterA",followed
by one time using "transmitter B".
PROGRAMMING TRANSMITTERS:
Itisimportanttorememberthatduringprogramming,eachindividualstepofthe
proceduremustbe executedwithin15seconds ofthepreviousstep. When the
15 second time limit is allowed to expire, the system will automatically exit
program mode. This is indicated by a long "chirp"(*) from the siren.
Additionally,anytimetheignitionkeyisturnedoffwhileprogramming,thesystem
will immediately exit program mode. This is also indicated by a long "chirp"(*)
fromthe siren.
TO PROGRAM ADDITIONAL TRANSMITTERS:
1. Enter the vehicle, and turn the ignition key to the "on" position.
2. Move the valet/bypass switch on - off - on - off - on then off.
3. The dash L.E.D. will flash(*) one time, and the siren will "chirp"(*) one time,
indicating the system is ready to accept programming for channel 1, or the
arm/disarmandpanicfunctions.
4. You can assign any of the three transmitter button functions listed below to
channel1.
a) Pressing button 1 on the keychain transmitter.
b) Pressing button 2 on the keychain transmitter.
c) Pressingbothbuttonssimultaneouslyonthekeychaintransmitter.
5. Pressandholdtheselectedchoicea,b,orcabove,untilthesirenemitsalong
"chirp"(*) to confirm that programming of channel 1 was successful.
6. Move the valet/bypass switch on, then off again.
7. ThedashmountedL.E.D.willflash(*)2times,andthesirenwill"chirp"(*)one
time,indicatingthatthesystemisreadytoacceptprogrammingforchannel
2, or the pulsed ground output for remote trunk release, remote car starter,
etc.
8. Youcanassignanyoneofthetworemainingbuttonfunctionslistedin4a,4b,
or4cabovetooperatechannel2. Youcannotusethebutton(s)thatoperate
channel 1, selected in step 5, to operate channel 2.
9. Press and hold the selected choice. The siren will emit a long "chirp"(*) to
confirmthatprogramming ofchannel 2was successful.
* Except PRO-9246R & PRO-9445

128-4618
sht. 3 of 4
L.E.D.
1Flash
2Flashes
3Flashes
CHANNEL
1
2
3
VALETSWITCH
ON then OFF 3 Times
ON then OFF 4 Times
ON then OFF 5 Times
Afterthedesiredchannelisprogrammed,turntheignitionkeytotheoffposition
toexitprogrammingmode.
BATTERY REPLACEMENT:
The transmitter incorporates a small red L.E.D. built into the case. This L.E.D.
canbe usedtoindicatebatterycondition. Youwillnoticeadecreaseintransmitter
rangeas thebatterycondition deteriorates. Toreplace thebattery...
1. Removethetransmitter coverbyremovingthesmallscrewfrom thebackof
thetransmittercase.
2. Removethe discharged battery,making noteof theorientation ofthe+ and
- contacts, and dispose of properly.
3. Installthenew(typeGP23A)battery,takingcaretoorientthe+and-contacts
properly.
4. Replace the transmitter cover, taking care not to damage the L.E.D. or
switches on the circuit board.
* Except PRO-9246R & PRO-9445
10. Move the valet/bypass switch on, then off again.
11. ThedashmountedL.E.D.willflash(*)3times,andthesirenwill"chirp"(*)one
time,indicatingthatthesystemisreadytoacceptprogrammingforchannel
3. (PRO-9249R & PRO-9246R)
12. Pressandholdtheremainingtransmitterbuttonfunction. Thesirenwillemit
a long "chirp"(*) to confirm that programming of channel 3 was successful.
13. Toexitprogrammode,eitherturntheignitionkeytotheoffposition,ormove
the valet switch on then off one additional time. This is indicated by a long
"chirp"(*) from the siren.
QUICK REFERENCE:
Youcanprogramanyindividualchannel,withoutreprogrammingallchannels,
byfollowing thequickreference chartbelow.

ORDER FORM FOR 2 BUTTON TRANSMITTER
MODEL NO. PRO 94 BT2
128-4618
sht. 4 of 4
AudiovoxCorporation
150MarcusBlvd.
Hauppauge,N.Y. 11788
Attn:TRANSMITTERDEPARTMENT Form No. 128-4618
Creditcardpurchaserscanorderadditionalorreplacement
transmittersbyphone. Simplydial1-800-645-4994,and
followtheinstructionsfromtheoperator interface.

IMPORTANT: Tohelpusexpediteyourorder,pleaseprintalloftheinformation
legibly,andmailthisformandyourpaymentaccordingtotheinstructionsbelow.
1.Name :________________________________________________________
Address:________________________________________________________
City:______________________ State:________ ZipCode:________________
2. TelephoneNumber:(__________)__________________________________
3. Enterthetotalnumberoftransmittersrequiredhere:______________________
4. The cost per transmitter is $ 65.00.
5. Enterthetotalamountenclosedhere:_________________________________
( New York state residents must include the appropriate sales tax. )
6. Method of payment; check one of the boxes below.
Mastercard Visa Check or money order * (do not send cash)
*Make checks payabletoAudiovox Corporation
7. CreditCardNumber:_____________________________________________
8. CreditCardExpirationDate:_________________________
9. Mail this form, and your check, to ;