AUO PFSDM32 Series User manual

Connecting To The DisplayInputs/Outputs
Quick Start Guide
PFSDM32/PFSDM43/PFSDM50/
PFSDM55 Series
(P320HVF06/P430HVF07/
P500HVF04/P550HVF16 Series)
Item Description
6DVI Connects with the digital video output of a computer and
other devices.
3Power Switch Switches the main power on/off.
1-1
1-2
See “Keypad” for detailed information.Keypad
2Disperses heat from the display.Air Vents
5RS232 Connects with the serial IO connector of another device.
7HDMI Connects with devices transmitting audio/video using the
HDMI interface.
8VGA Connects with the analog video output (VGA) of a
computer, etc.
Connects with the audio out connector of a video source
such as a computer, VCR, or DVD player when the display is
connected to the source via the VGA or DVI connector.
9AUDIO IN
4AC-IN Connects with the supplied power cord.
CAUTION: Avoid applying force or using sharp objects on
the screen or the frame around the screen at all times.
CAUTION: Never press or place anything on the back cover.
This may damage the internal parts of the display.
11 IR IN Connects with an external IR sensor module.
NOTE: From the tip to the terminal the plug
sections are defined as IR / VCC / Ground.
10 AUDIO OUT Connects with external speakers or audio amplifier to
output the audio that is supplied by the video source.
NOTE: Headphones and earphones are not
supported.
12 DP
(DisplayPort)
Connects with devices transmitting audio/video using the
DisplayPort interface.
NOTE: The DisplayPort input function will be
disabled if a Smart Display Module (SDM) is installed
in the display.
13 IR Sensor and
Power LED
Receives the signal from the remote control.
Indicates the power status of the display.
Green
Red
Off
The display is powered on.
The display is in stand-by mode.
The display is powered off.
Digital Connection
Analog Connection
Safety Information
Carrying the Display
When carrying the display, always carry it
using both hands and with the LCD panel
facing forward. DO NOT carry the
display while putting pressure on the
screen at the front of the chassis.
Placing the Display
When placing the display, always put the screen face
down as illustrated in the Setting Down the Display
section. Never stand the display upright. Never tilt the
display towards the left, right or balanced on a single
corner of the frame.
Setting Down the Display
When setting the display down, place the
screen face down on a flat and stable surface
covered by a protective sheet and a table
cushion as shown in the illustration provided.
50” 32”43”55”
2
5678
10
11 9 34
13
1-1
12
1-2

2
1
3
4
5
DO NOT REMOVE
1
3
2
4
50"
InstallationPackage Contents
Video Output Via SDM (Optional)
Adjusting Directions Keypad
Remote Control
Installation on a Flat Wall
(Minimum Distance: 40mm)
Wall Mounting
For proper installation it is strongly recommended to use a trained,
qualified technician.
The back of the display is equipped with four screw-holes with dimensions of
200 x 100mm (for 32”), VESA mount 200 x 200mm (for 43” and 50”), or VESA
mount 300 x 300 mm (for 55”). Firmly secure a wall mount onto the display
using four M6 screws (maximum length: 20mm, maximum torque: 16 kgf-cm).
When installing the display on a wall face, there has to be
at least 40mm of space between the display and the wall
for ventilation purposes.
The display must be installed in an environment with
proper ventilation to prevent it from overheating. Do not
block the ventilation holes on the top, left, and right sides
while keeping the display away from any heat source.
Controlling The Display
Remote Control and
AAA Batteries
Power Cord (Japan)
(By regional request)
SDM video output signal type based on SDM
model (for Set 1).
Remove screw 1, 2, 3, and 4 to remove SDM-L.
Remove screw 3 and 4 to remove SDM-S.
Refer to the figure on the right to use an SDM
to broadcast on 2 displays (Set 1, Set 2) or 3
displays (Set 1, Set 2, Set 3).
When using an SDM, configure the settings as
indicated below:
1) OSD Menu > Setup > SDM/DP Power >
Keep
2) OSD Menu > Setup > RS232 Switch >
SDM
Horizontal (Landscape) Vertical (Portrait)
NOTE: To prevent glare when used in a
location with strong sunlight, it is recommended
to add a cover over the display.
Item Description
3DOWN Moves the selection in the OSD menu left/down.
UP Moves the selection in the OSD menu right/up. 4
2MENU !Displays the On Screen Display (OSD) menu.
!Selects an item in the OSD menu.
5EXIT Exits the current menu when the OSD menu is on.
POWER Turns the power on/off.
1
NOTE: This button does not work when the
power switch is off.
1
2
3
4
6
7
8
Button Description
7SOURCE Switches the video input
source. Use the [!] or ["]
buttons to directly select
[D-SUB], [DVI], [HDMI],
[SDM/DP].
1POWER Switches the power on/off.
When the power indicator
is not lit, no controls will
work.
2MENU Displays the OSD menu.
4EXIT Exits the current menu.
5MUTE Silences the audio from the
display.
6ENTER Accepts the settings made
in the OSD menu.
8VOL Adjusts the display’s volume
([+] to increase, [-] to
decrease).
NOTE:
!Be careful to avoid tipping the display over when attaching
accessories.
!" Periodically check for loose screws, gaps, distortions, or other
problems that may occur with the mounting apparatus. If a
problem is detected, please refer to qualified personnel for service.
!" #$%&'()'*"+,$+-".,$"/0&1.21%"'0+(.201"30)"42%14"03"5(/(%$"0r
weakness that may occur over time.
Power Cord
(USA/Taiwan)
(By regional request)
Display
3Moves the selection in the
OSD menu.
[!] / ["] /
[#] / [$]
90°
40
mm
Set 1
Set 2
(Signal Out)
Set 3
(if the SDM has a
video I/O output)
NOTE:
!Please follow the normal shutdown procedures (Shut Down
SDM OS > Turn AC Off).
!Turn the AC power off first before installing or removing an
SDM.
!Signal out port is available only when an SDM is installed. To
control the connected displays via the RS232 port of the SDM,
set OSD menu > Setup > RS232 Switch > SDM.
NOTE: The user manual can be downloaded from
https://pid.auo.com
SDM module Installation
Power Cord (Europe/Korea)
(By regional request)
32” 43”
50” 55”
32"/43"/55"
200.00mm
100.00
mm
200.00mm
200.00mm
200.00mm
200.00mm
300.00mm
300.00mm
2
1
3
4
5
5
49.55S1S.003