AUTHOR Alarm Kord User manual

OPERATING MANUAL

version 802.1

3
General information ........................................................... 4
Installation scheme ........................................................... 5
Connection between IGLA and KORD .......................... 6
Specications ....................................................................... 7
Contents of the set ............................................................ 7
TABLE OF CONTENTS

4
General information
KORD is designed for control of additionally installed
electromechanical hood lock. The module is supplied
as an addition to the IGLA anti-theft system and
considerably expands security functions of the system.
Devices are connected via standard CAN bus in an
encrypted dialogue mode. This excludes unauthorized
access to hood lock control features.
KORD module controls the status of hood open, in
other words the hood lock cannot be locked if the hood
is opened.*
The hood lock is closed in the following cases:
• Car security is activated (the central lock is closed)
• In 10 seconds after the ignition is off
• Anti Hi-Jack mode is activated
(right after the car starts moving)
The hood lock does not close if the hood is opened or
IGLA has service mode activated.
The hood lock unlocks after the authorization in the
IGLA system.
* Only for the cars that have information about opening of the hood in its CAN
bus.

5
Installation scheme
To connect KORD module connect its wires the
following way:
1. Black. To power supply «-» (ground/earth).
2. Purple. To the hood lock activator (12A max). Power
supply «+» to close the lock.
3. Green. To the hood lock activator (12A max). Power
supply «+» to open the lock.
4. Red. To power supply «+» (12 V).
5. Grey. To power supply «+» while connecting to IGLA.
6. Yellow. Not used.
7. Brown. CAN-H.
8. White. CAN-L.
ATTENTION! Grey and red wires should be
simultaneously connected to Power supply «+» to
connect with the IGLA anti-theft device when it is in
PIN-code change mode.
+12V
To the hood lock
activator
To the hood lock
activator
Vehicle CAN bus

6
Connection between IGLA and KORD
Follow these steps to connect the devices:
1. Switch IGLA into PIN-code change mode by one of
the following ways:
• connect the grey wire from IGLA to Power supply
«+» and switch on the ignition;
• if the device is already connected, after the
authorization is successful enter the current PIN-
code once again while pressing the accelerator
pedal as far as it can go*.
ATTENTION! If you need to connect 2 and more KORD
modules only PIN-code change mode can be used
(enter the PIN-code once again with the accelerator
pressed*). If the grey wire is used while connecting
to KORD module all previously connected to IGLA
devices will stop functioning!
ATTENTION! For the connection of the second and
subsequent devices all previously connected devices
shall be disconnected from CAN-bus or power supply.
2. Connect the hood lock control module as
described above.
3. Apply power supply «+» to Grey and Red wires at
the same time.
4. The hood lock will open, close, and open again
within 5 seconds.
After that you can switch off the ignition and disconnect
the grey wire from power supply «+». Modules are
connected.
* For some car models other controls are used instead of an accelerator pedal
(see the annex to the IGLA operating manual).

7
Specications
Current consumption in the standby mode ............. 5 mА
Maximum current to the lock activator .................... 12 А
Operating voltage ...................................................... 6-16 V
Contents of the set
KORD module ............................................................... 1 pcs.
Operating manual ....................................................... 1 pcs.
Packing .......................................................................... 1 pcs.
Made in Russia
Manufacturer: LLC «DMA Group»
C-RU.АЛ14.В.10097
The developer and the manufacturer retain the right to make technical
updates not specied in this operating manual. To learn more visit our
web-site:
http://author-alarm.com

8
WARRANTY CERTIFICATE
Warranty is 12 months from the date of the purchase. During this
period technical support and maintenance are guaranteed for free.
The warranty does not apply to the items with:
• mechanical damage, burnt and char pieces, components,
conductive tracks etc.;
• traces of an independent repair;
• damage caused by natural hazards, re, social factors;
• violation of the tamper-evident seal, damage or absence of a
factory/trade label.
Only items in complete set and with the original packing are taken for
warranty repair.
Absence of packing is regarded as noncompliance with transportation
rules. The warranty does not apply to the damage incurred to another
equipment operating together with this device.
Item (model) ________________
Sale date ______/____/________
The contents of delivery ___, functioning ___, absence of mechanic
damage ___ are checked.
I am acquainted and agree with the condition of warranty service:
Buyer ______________________________
Seller ___________________________ seal

Supported Cars List App.