AutoAqua Smart ATO nano User manual

SATO-270D
Smart ATO nano

List of Parts (Can Be Purchased Separately)
Item Picture Description
1
Caution:RiskofInjuryfromStrongMagnets
1. Integrated with one dual
sensor and one replaceable
diaphragm pump
2. Mounting Thickness :
0.12-0.39 inch (3-10 mm)
Smart ATO nano
Controller
Input : 100-240 V 50-60 Hz
Output : 12V 1A
Universal Power
Adapter
Tubing 6.5 feet
(200 cm)
Used with Diaphragm Pump,
Prelter and Anti-Siphon Valve.
A cleanable connector
to remove particles in
the reservoir
Prelter
1. A valve to stop the forward
siphon pressure up to 2 feet
(60 cm) of water.
2. Adding one more valve
(optional) can stop a higher
forward siphon pressure.
Anti-Siphon Valve

Smart ATO nano Controller
2
8
7
2
3
4
5
6
1
Prelter
Open
Close
Holes for Fixing Water Inlet Tube
Power Jack
Water Inlet
Water Outlet
Holder
Hole for Fixing Water Outlet Tube
Failsafe Sensor
ATO Level Sensor
1
2
3
4
5
6
8
7
1. Power Input : 100-240 V 50-60 Hz
2. Diaphragm Pump
Suction Head : 6.5 feet (200 cm)
Flow Rate : 7.9 gph (30 lph)
3. Tubing I.D. : 5/32 inch (4 mm)
O.D. : 1/4 inch (6.4 mm)
4. Mounting Thickness
Sensor : Max.1/2 inch (12.7 mm)
Holder : 0.12-0.39 inch (3-10 mm)
5. Anti-Siphon Pressure : 2 feet (60 cm) of
water
Specifications

1. Take off the cover of Smart ATO nano controller and x it on
tank/sump with the holder.
2. Mount the sensor with the magnet at the normal water level (with
the water level reaching the lower one) . If the cable is too long, *
push it back into the main body.
3. Cut the tube to a proper length. Connect the water inlet tube with
the Prelter and put it in the water.
4. Connect water outlet tube and insert it into the holder.
5. Connect the white part of the Anti-Siphon Valve to the end of the
tube and keep it out of water.
6. Put the cover back on Smart ATO nano controller and x the tube
with the hole on the side of the cover.
7. Connect power and do one-time lling to check there is no water
dripping (forward siphon) after the pump stops.
8. Unplug and plug the power adapter back in for reset.
3
*Please set the sensor away from the water outlet to avoid bubble
interference.
Tank/Sump
Anti-Siphon Valve
Optical Level Sensor
Prelter
Anti-Siphon Valve :
The white part is
water inlet. Keep it
always out of water.
Water Inlet
Anti-Siphon
Pressure
Prelter :
The Prelter must
be installed before
the inlet of the
diaphragm pump.
Water Inlet
Reservoir
Installation

4
Smart ATO nano uses QST for real-time protection against any failure
situation. The controller will give a visual alert when it senses any
other relling time is 6 times longer than the rst lling time. QST *
can detect the malfuction of the sensor or the pump, and the empty
reservoir to avoid the pump running dry. For example, if the rst
lling time is 10 sec., it will alert when any other relling time is over
60 sec.
*No security time control for the rst lling.
LED Color Status Description Action
Alternating
& Blue Red
LED
Flashing Boot-up N.A.
N.A.
N.A.
N.A.
Solid
Flashing
Power on
Relling/Pumping
QST alarm :
1. Bubble interference
2. Empty reservoir
The fail-safe sensor
senses the water
level changes.
Flashing
1. Clean the sensor or
move it to an area
away from micro
bubbles.
2. Rell the reservoir.
LEDBlue
LEDRed *
Flashing
quickly for a
short time**
*Please follow the instruction above to x issues and then unplug the
power and plug it back in.
**For very small aquariums, the top sensor may be triggered after each
top off. This is normal and no action is required.
LED Indicator
Quick Security Technology (QST)

1. Limited warranty is provided by AUTOAQUA only if your
AUTOAQUA Product ("Product") was purchased from an
authorized distributor or an authorized reseller.
2. All warranty repairs or replacement are performed by the
authorized distributor or authorized reseller in the region where
the Product was rst shipped by AUTOAQUA.
3. The limited warranty is valid for a period of 1 year under proper
installation and normal use from the date of the original purchase
listed on the proof of purchase or sales receipt.
4. In the event of a limited warranty claim, proof of purchase or
sales receipt (issued to the original purchaser) is required.
Warranty Period
Place of Purchase Service
Purchase Date
(Store name, phone, email, address)
(Y/M/D)
AUTOAQUA Technologies Co., Ltd.
7F-7.,NO.229,Fuxing 2nd Rd.,Zhubei
City, Hsinchu County,Taiwan
E-mail : [e-mail]
www.autoaqua.com.tw
* Please go to AUTOAQUA website to
get the distributor information.
One year from the purchase date
5
1. Please read the manual before installation. Keep the power adapter
dry and avoid any contact with water to prevent malfunctions.
2. Make sure the water ows through the tubing smoothly .
3. Please open and clean the prelter every 3 to 6 months for best
lter performance.
4. Please visit AUTOAQUA's website to know how to replace the pump.
Notice
Limited Warranty