Autronica AutroSafe BS-60 User manual

P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
Fire Alarm Control Panel
BS-60
Commissioning handbook
Program version
P1-BS60-202E-0

BS-60 Commissioning handbook
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
Contents
Page
0. Intrduction ....................................................................................3
1. Pre-commissioning checks.........................................................3
1.1 Recommended checking equipment ........................................3
1.2 Test procedure ........................................................................3
2. Connections ................................................................................4
3. Switch setting...............................................................................5
3.1 Setting the S18 DIP switch on the BSA-60 circuit board ..........5
3.2 Setting the control panel’s ASSP address on S17 switch.........5
4. Configuration................................................................................6
4.1 Menu strukture..........................................................................6
4.2 Configuration preaction ............................................................7
4.3 System Configuration ...............................................................7
4.3.1 Configuration - DATA.........................................................8
4.3.2 Configuration - ZONE ......................................................12
5. Service (Password protected on service level) ................16
5.1 Alarm-test ...............................................................................16
5.2 Custom-text ............................................................................17
5.3 Watchdog-counter..................................................................17
6. Custom design text....................................................................18
7. Texting the front of the Fire Alarm Control Panel ..................18
Appendix A Paperstickers ..............................................................19
Appendix B Table for System configuration data ...........................20
Appendix C Table for Operating, service and maintenance ...........21
Appendix D BS-100 Master............................................................22
Appendix E Fault messages...........................................................26

BS-60 Commissioning handbook
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
0. Introduction
The program version P1-BS-60-201E-O is only to be implemented on
BSA-60 board labeled 7212-197-0003.
BSA-60 boards 7212-197-0001 and 7212-197-0002 has to be modified and labeled
BS-991.
“Updateing-kit” to BSA-60 has art.no. BST-10.
1. Pre-commissioning checks
1.1 Recommended checking equipment
High-ohmic universal measuring instrument.
(internal resistance about 5 Mohm).
1.2 Test procedure
a) Check that all the cables are properly connected to List 1, 2 and 3.
b) Disconnect the ribbon cables on List 1 and 2 check that the mains and battery
fuses are removed. See fig. no. 1.
c) Measure the total resistance in the loop is the following manner:
Measure between the cable ends on terminal List 1.1 and 2 (A and A’) and
between 3 and 4 (B and B’).
Total resistance must not exceed 30 Ohm.
If the loop contains BK-30 loop break units, they must be bypassed in order to
make it possible to measure the resistance.
d) Check all cables for “stray voltage”.
e) Check for proper earth (that the control panel is earthed).
f) On systems when mains have “grounded” 0V point, ensure that the mains live
is connected to “L”, List 3, terminal 3. (This input has a fuse).
Introduction
Checking
Test procedure

BS-60 Commissioning handbook
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
2. Connections
a) When the checking procedure has been carried out, connect the ribbon cables
for List 1 and 2.
b) Place the batteries on the bracket and connect them to the wires in the cabinet.
c) Connect the fuses in accordance with fig. no. 1.
Placement of fuses on the BSA-60 circuit board and on the BSS-100 power
supply unit.
123456 78
LIST L3
Fig. no. 1
F1 0,63A T AK1 F5 4A T 24V DC in
F2 0,63A T AK2 F6 4A T Battery
F3 0,63A T AK3 F9 1A T Output SSK
F4 0,63A T AK4 Control 1 and 3
Connections
R54
S17
S18
D4
X7
F4 F3 F2 F1
F9 F5 F6
X4
X3
X6
X5
X1
X2
LIST 2
LIST 1
BSA-60
circuit board
Main fuse: (BSS-103, F1) 1,4AT
N
ot in use.
Ext. 24V outp.
(BBS-103, F3):1AT
BSS-103
Battery
X9
+ -
Control 3
R54: For display
contrast adjustment D4: EPROM for programme
DIP-switch S18
Rotating switch S17
Reverse side of
the BSA-60
circuit board
Fuses,
sounders circuit:
F
ront plate

BS-60 Commissioning handbook
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
3. Switch setting
3.1 Setting the S18 DIP switch on the BSA-60 circuit
board
The S18 switch is located on the reverse side of the front panel.
To get access to this switch, open the front panel by unscrewing the large screw to
the right of it.
Setting of DIP-switches must be carried out with no power connected to the system.
(Does not affect switch S18 element 1.)
(Do NOT use a pencil to operate the switches!)
Switch elements:
Element
1
Element
2
Element
3
Element
4
Element
5
Element
6
Element
7
ON OFF OFF ON OFF OFF OFF
(Config. data
protection)
External
control of
alarm delay
from input
EXT.3(L1.25
)
ON= active
OF =
passive
(Remote/loc
al mode).
OFF=
Local mode
ON=
Remote
mode
Communica-
tion speed.
OFF=
9600 baud
ON=
1200 baud
ON=Custom
designed
test event
log is active.
Normal
position.
OFF=
Access to
the config.
menu.
Fig. no. 2
3.2 Setting the control panel’s ASSP address on S17
switch
If the control panel is a sub panel connected to BS-100, set the ASSP address (2-
F) of the control panel on the S17 switch.
If the control panel is an independent unit the switch must be in the “0”-position.
The switch is located under the S18 switch on the rear side of the front panel. See
fig. 2.
ON
OFF
R
ear side of the front panel
17
Rotating switch S17 DIP-switch S18
Switch setting

BS-60 Commissioning handbook
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
4. Configuration
4.1 Menu structure
The whole menu structure is shown here, but only “CONFIGURATION”, and
“SERVICE” is described in this handbook. For information about the other
functions, see “Operators handbook” for BS-60.
SELECT MAIN MENU
1-- Out/in- 1--Disable 1--Address
control 2--Zone
3-- Fire-brigade (BMA,BMFO,BMF)
A) 4 Sounders
5--Controls 1--BT-outputs (AUX,DHM)
2--Controls-1
3--Control-2
2--Restore 1--Address
2--Zone
3-- Fire-brigade
A) 4 Sounders
5--Controls 1--BT-outputs (AUX,DHM)
2--Controls-1
3--Control-2
3--Alarm delay
2--Test 1--Frontpanel/buzzer
2--BMA/BMF
3--Fault
4--Sounders
5--Controls 1--Zone-control
6--Alarm 2--Control-1
3--Control-2
3--Show- 1--Prewarning
status 2--Fault
3--Disablement
E) 4--Stored events
4--System 1--Sensitivity 1--Address 1--Single address
2--Beyond-limit 2--Total
2--Internal 1--Program-version
E) 2--Adjust-clock
E) 3--Show-clock
D) 3--Config. 1--Data
2--Zone 1--Start-no.
2--Edit 1--Insert
3--Renumber 2--Delete
3--Automatic 4--Delete 3--End
B) 4--Save 5--End
5--Service 1--Alarm - test
E) 2--Custom - text
3--Watch-dog - counter
Configuration

BS-60 Commissioning handbook
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
REMARKS A) IN ABOVE MENU STRUCTURE
A) The “DISABLE SOUNDERS” function is password
protected for the English version.
B) The “SAVE” function is always password protected
(spesial requirements are set to OFF, SOLAS or LPC).
C) The “SERVICE” function is always password protected
(spesial requirements are set to OFF, SOLAS or LPC).
D) The DIP-switch 18.7 has to be in position “OFF” to
reach the “CONFIGURATION” function.
E) The DIP-switch 18.7 has to be in position “ON” to
reach the “STORED-EVENTS”,”CUSTOM-TEXT”,
“ADJUST-CLOCK” and “SHOW-CLOCK” functions.
DEFAULT POSITION.
4.2 Configuration preaction
Before the configuration procedure is started, please check that S18.1 switch is set
in position “ON” (can be changed without powering down the panel).
To active the “CONFIGURATION”-menu, do as follows:
• Power down the panel.
• Set switch S18.7 in position “OFF”.
• Power up the panel.
This operation changes the menu structure and gives access to
“CONFIGURATION” (3) under the “SYSTEM”-menu.
SYSTEM: 1:SENSITIVITY 2:INTERNAL
2:CONFIGURATION
4.3 System Configuration
Select “CONFIGURATION” by pressing “3” in the “SYSTEM”-menu, and the
following text will appear in the display:
SYSTEM CONFIGURATION: 1:DATA 2:ZONE
3:AUTOMATIC 4:SAVE
NB! Saving of configuration changes is password portected. See sec. 4.3.4.
Config.
p
reaction
System
Confi
g
uration

BS-60 Commissioning handbook
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
4.3.1 Configuration - DATA
All default values set from the factory, can be edited.
Select “DATA” by pressing “1” in the “SYSTEM CONFIGURATION”-menu, and the
following text will appear in the display:
SPESIAL REQUIREMENTS: 00
OFF = 00, SOLAS = 01, LPC =02
Select special requirements value and press ↵
↵↵
↵.
The following text will appear in the display:
RESET-NUMBER: 100
Verify or correct the reset-number (number of detectors in the loop + 1),
and press ↵
↵↵
↵.
The following text will appear in the display (SOLAS program version will jump
directly to “Alarm Delay T2”):
ALARM DELAY T1 (0 - 10) MIN: 02
By us of D/N-function switch S18.2 must be in “ON” position and 0 voltage must be
connected to pt. L1.25.
The alarm delay T1 of sounder output 1 - 4 (and BMA, alarm output) can be
selected in the 0 - 10 minute range. A second or manual alarm will not have this
delay.
Press ↵
↵ ↵
↵ and the following text will appear in the display:
ALARM DELAY T2 (0-30) MIN: 10
The alarm delay T2 of sounder output 1 - 4 (and BMA, alarm output) can be
selected in the 0 - 30 minute range. A second or manual alarm will not have this
delay.
The “SOLAS” program version has always 2 minutes delay after 1st alarm, also for
manual call-points.
Press ↵
↵ ↵
↵ and the following text will appear in the display:
NUMBER OF CELLWARN: 00
Enter number of zone operating units (BK-50, if mounted) and press ↵
↵↵
↵.

BS-60 Commissioning handbook
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
The following text will appear in the display:
MAINS FAILURE DELAY (1 - 35) MIN: 35
The mains failure can be delayed within the 1 - 35 min. range. If 35 min. is selected
the mains failure is disabled.
Press ↵
↵↵
↵, and the following text will appear in the display:
FIRE BRIGADE ALARM DELAY: 1
ON = 1, off = 0
ON - Any delay (T1 + T2) selected above.
OFF - There will be no alarm delay.
Select ON / OFF.
Press ↵
↵↵
↵, and the following text will appear in the display:
SOUNDER OUTPUT-1 ALARM DELAY: 1
ON = 1, OFF = 0
Only delay time of sounder output-1 can be turned ON/OFF.
ON - Any delay (T1 + T2) selected above.
OFF - There will be no alarm delay.
Select ON / OFF.
This function gives possibility to direct alarm on sounder output 1 and delay on
outputs 2-4.
Press ↵
↵↵
↵, and the following text will appear in the display:
CONSTANT ALARM SIGNAL: 0
ON = 1, OFF = 0
Concern both sounders and internal buzzer.
ON - Constant alarm signal.
OFF - Pulsating alarm signal.
(SOLAS program version gives always constant signal on output 4 (AK4).
Select ON/OFF.
Press ↵
↵↵
↵, and the following text will appear in the display:
SHORT CIRCUIT SOUNDER MONITOR: 1
ON = 1, OFF = 0
This funciton has to be turned off when low-ohm sounders or sounders without a
blocking diode (older installations) are connected.
Select ON/OFF.
Press ↵
↵↵
↵, and the following text will appear in the display:
SILENCE/RESOUND SOUNDER FUNCTION: 1
ON = 1, OFF = 0

BS-60 Commissioning handbook
P-BS60/EEE/Doc/020402 Autronica Fire and Security AS
This function is used when the BS-60 control panel serves as a slave to master.
When selecting OFF, it will only be possible to stop the sounder from a master.
IF BS-60 is the main panel (independent), then select ON:
Switch S18.3 OFF: Silence sounder both from BS-60 and BS-100.
ON: Only from BS-100. Select ON/OFF.
Press ↵
↵↵
↵, and the following text will appear in the display:
RESET FUNCTION: 1
ON = 1, OF =0
This function is used when the BS-60 control panel serves as a slave to a master.
When selecting OFF, it will only be possible to reset the system from a master. If
BS-60 is the main panel (independent), then select ON:
Switch S18.3 OFF: Reset from both BS-100 and BS-60.
ON: Only from BS-100.
Select ON/OFF.
Press ↵
↵↵
↵, and the following text will appear in the display:
POWER LED SPECIAL FUNCTION: 0
ON = 1, OFF = 0
ON - The main lamp will light when the control panel has correct internal 24V power
supply.
OFF - The main lamp will only light when the control panel is connected to a voltage
supply (230V AC).
Select ON/OFF.
Press ↵
↵↵
↵, and the following text will appear in the display:
INVERT BMF OUTPUT: 0
ON = 1, OFF = 0
ON - The BMF (fault output) is activated when the control panel is powered, and
deactivated if any fault event occurs.
OFF - The BMF is activated if any fault event occurs.