Avalue Technology SID-10W03 User manual

Part No. E2017D153A0R
SID-10W03
SID-10.1" w/Atom z8350 2G RAM/32G eMMC
Quick Reference Guide
1st Ed –26 November 2020
Copyright Notice
Copyright 2020 Avalue Technology Inc., ALL RIGHTS RESERVED.

SID-10W03
2 SID-10W03 Quick Reference Guide
FCC Statement
Federal Communication Commission Interference Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice:
(1) A Unshielded-type power cord is required in order to meet FCC emission limits and also to prevent
interference to the nearby radio and television reception. It is essential that only the supplied
power cord by used.
(2) Use only shielded cables to connect I/O devices to this equipment.
(3) Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

Quick Reference Guide
SID-10W03 Quick Reference Guide
3
FCC RF Radiation Exposure Statement
This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found compliant
to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF
Exposure from radio frequency devices. The radiated output power of this Wireless LAN device is far
below the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a
manner that the potential for human contact during normal operation is minimized. When nearby
persons has to be kept to ensure RF exposure compliance, in order to comply with RF exposure limits
established in the ANSI C95.1 standards, the distance between the antennas and the user should not
be less than 20 cm.
WARNING
“CAUTION –Use suitable mounting apparatus to avoid risk of injury.”
“CAUTION - Use a power cord that matches the voltage of the power outlet, which has been
approved and complies with the safety standard of your particular country.”
“WARNING –To avoid risk of electric shock, this equipment must only be connected to a supply
mains with protective earth.”
Notice
This guide is designed for experienced users to setup the system within the shortest time.
For detailed information, please always refer to the electronic user's manual.
Copyright Notice
Copyright 2020 Avalue Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective
owners.
Disclaimer
Avalue Technology Inc. reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve
design and/or performance. Avalue Technology assumes no responsibility or liability for the
use of the described product(s), conveys no license or title under any patent, copyright, or
masks work rights to these products, and makes no representations or warranties that

SID-10W03
4 SID-10W03 Quick Reference Guide
these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration
purposes only. Avalue Technology Inc. makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
Life Support Policy
Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN
LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL
OF Avalue Technology Inc.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into body, or (b) support or sustain life and whose failure to perform,
when properly used in accordance with instructions for use provided in the labeling, can
be reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose
failure to perform can be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or effectiveness.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/

Quick Reference Guide
SID-10W03 Quick Reference Guide
5
Content
1. Getting Started............................................................................................................6
1.1 Safety Precautions ................................................................................................6
1.2 Packing List...........................................................................................................6
1.3 System Specifications ...........................................................................................7
1.4 System Overview.................................................................................................10
1.4.1 I/O View...................................................................................................................................... 10
1.5 System Dimensions.............................................................................................11
2. Hardware Configuration...........................................................................................12
2.1 SID-10W03 connector mapping...........................................................................13
2.1.1 Serial port connector (COM)...................................................................................................... 13
2.1.2 RJ-45 Ethernet connector (LAN) ............................................................................................... 13
2.1.3 HDMI connector (HDMI) ............................................................................................................ 14
2.1.4 USB2.0 connector (USB2.0)...................................................................................................... 14
2.1.5 USB3.0 connector (USB3.0)...................................................................................................... 15

SID-10W03
6 SID-10W03 Quick Reference Guide
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x SID-10W03 Panel PC
1 x AC/DC adapter 12V/5A 90 Screw Type
1 x Power cord
1 x WiFi Antenna
4 x Screw-Flat M4* 4mm

Quick Reference Guide
SID-10W03 Quick Reference Guide
7
1.3 System Specifications
Component
Mother Board
ACP-CHT3
CPU
Intel Atom x5-8350 Quad Core 1.44GHz up to 1.92GHz
CPU Cooler (Type)
Aluminum shielding cover
Memory
2GB / 4GB DDR3L on board
Power Supply
12V~24V wide voltage DC-input
Adapter
12V/5A is default power adapter
Wireless LAN
802.11 ac/b/g/n Wireless LAN on board
Bluetooth
Bluetooth 5.0 on board
Operating System
Windows 10 2019
Storage
Solid State Drive
32GB eMMC, Optional 64GB MMC
Panel
LCD Panel
-10.1” TFT-LCD, 16:10, 1280 x 800
-LVDS Interface
Touch Screen
-Projective Capacitive Touch,10 points
-Hardness:7H
-Transmission: 86%
External I/O
LAN Port
1 x 10/100Mbps Fast Ethernet(RJ-45 connector)
USB Port
1 x USB 3.0, 2 x USB 2.0 Ports
Video Port
1 x HDMI (type A)
Audio Port
1 x Line out (3.5mm Phone jack/Green)
Serial Port
Optional 1 x RS-232((Tx/Rx) or RS-485
Wireless connector
1 x SMA type connector for dipole antenna
Power Requirement/Mechanical
Power Type
12V~24V DC-Input
Power Connector
Type
2.5mm DC-in jack
Construction
Metal
Color
Black
Dimension
255.2 x 169.4 x 40.7mm
Weight
1.36 kg
Fanless
Yes
IP Rating
Front IP65
Reliability

SID-10W03
8 SID-10W03 Quick Reference Guide
EMI Test
CE/FCC Part 15, Subpart B
Safety
IEC-60950-1 & EN 60950-1
Dust and Rain Test
Front Panel IP65, Rear IP41 except I/O
Random Vibration
Test
Test Standard: Reference IEC60068-2-64 Testing procedures
1. System condition: Operation mode
2. PSD: 0.00454G²/Hz , 1.5 Grms
3. Test Frequency : 5-500Hz
4. Test Axis : X,Y and Z axis
5. Test time: 30 minutes per each axis
6. Storage : eMMC
Sine Vibration Test
(Non-operation)
Test Standard: Reference IEC60068-2-6 Testing procedures
1. System condition : Non-Operating mode
2. Test Acceleration : 2G
3. Test frequency : 5~500 Hz
4. Sweep：1 Oct/ per one minute. (logarithmic)
5. Test Axis : X,Y and Z axis
6. Test time :30 min. each axis
Packing Vibration
Test
Test Standard: Reference IEC60068-2-64 Testing procedures
1. Non-operation mode
2. PSD: 0.026G²/Hz , 2.16 Grms
3. Test Frequency : 5-500Hz
4. Test Axis : X,Y and Z axis
5. Test time: 30 min. per each axis
Mechanical Shock
Test
Test Standard: Reference IEC60068-2-29 Testing procedures
1. System Condition: Operation
2. Wave form: Half-Sine wave
3. Acceleration: Rate: 10g
4. Duration: Time: 11ms
5. No. of Shock: Z axis 300 times
6. Test Axis: Z axis
Packing Drop Test
Reference ISTA 2A, Method: IEC-60068-2-32 Test:Ed
1. Test Phase: One comer, three edges, six faces
2. Packing weight: around 1.5kg
3. Test high: 96.5cm (Based on product weight
Operating
Temperature
0°C ~ 40°C (32°F ~ 104°F)
Operating Humidity
40°C @ 95% Relative Humidity, Non-condensing
Storage Temperature
-20°C ~ 60°C (-4°F ~ 140°F)

Quick Reference Guide
SID-10W03 Quick Reference Guide
9
Note: Specifications are subject to change without notice.

SID-10W03
10 SID-10W03 Quick Reference Guide
1.4 System Overview
1.4.1 I/O View
Connectors
Label
Function
Note
Line out
Audio line-out connector
Head phone jack
HDMI
HDMI connector
HDMI type A
USB2.0
2 x USB2.0 connector
USB3.0
USB3.0 connector
DCIN
DC power-in connector
DC jack
LAN
RJ-45 Ethernet connector
COM
Serial port connector
DB-9 male connector