Avalue Technology AID-173SHR User manual

1
Avalue Intelligent Display & Systems
AID-173SHR
All-In-One Medical PC
Quick Reference Guide
2nd Ed- 19 May 2014
Copyright © 2014 Avalue Technology Inc., All Rights Reserved
.

2
Federal Communication Commission Interference Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Notice:
(1) A Unshielded-type power cord is required in order to meet FCC emission limits and also to
prevent interference to the nearby radio and television reception. It is essential that only the
supplied power cord by used.
(2) Use only shielded cables to connect I/O devices to this equipment.
(3) Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

3
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body. For product available
in the USA/Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible. The antenna(s) used for this transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Shielded interface cables must be used in order to comply with emission limits.

4
WARNING
“WARNING: Users must not allow SIP/SOPs and the patient to come into contact at
the same time.”
“CAUTION – Use suitable mounting apparatus to avoid risk of injury.”
“CAUTION - Grounding reliability can only be achieved when the equipment is
connected to an equivalent receptacle marked “Hospital Only” or “Hospital
Grade”.”
“CAUTION - Use a power cord that matches the voltage of the power outlet, which
has been approved and complies with the safety standard of your particular
country.
“WARNING - Do not modify this equipment without authorization of the
manufacturer.”
“WARNING – To avoid risk of electric shock, this equipment must only be
connected to a supply mains with protective earth.
“WARNING –Thorough guiding shall be made to children users to ensure correct
use of the product and beware of certain risk it may cause by phone cord and other
small parts.”
“CAUTION: This adapter AdapterTech ATM065-A190 is a forming part of the
medical device”

5
Statement
Accessory equipment connected to the analog and digital interfaces must be in
compliance with the respective nationally harmonized IEC standards (i.e. IEC
60950 for data processing equipment, IEC 60065 for video equipment, IEC 61010-1
for laboratory equipment, and IEC 60601-1 for medical equipment.) Furthermore all
configurations shall comply with the system standard IEC 60601-1-1. Anyone who
connects additional equipment to the signal input part or signal output part is
configuring a medical system, and is therefore, responsible that the system
complies with the requirements of the system standard IEC 60601-1-1. The unit is
for exclusive interconnection with IEC 60601-1 certified equipment in the patient
environment and IEC 60XXX certified equipment outside of the patient
environment. If in doubt, consult the technical services department or your local
representative.

6
Intended Use
AID-173 Series Medical PC is intended to be used for displaying information and
providing interactive services by doctors, nurses, patients, and staff in the hospitals. It
shall not be used for diagnosis purpose and shall not be used for life supporting system.
Cleaning
Materials
Lint-free cloth, microfiber cloth, damp cloth
Method
Add rubbing alcohol, such as 70% Ethanol or Isopropyl, to the cloth
and clean the screen and plastic chassis of the medical PC.
Caution
DO NOT use cleaning solution, glass cleaner, or spray detergents
to clean the medical PC.

7
Explanation of Graphic Symbols
WARNING: dangerous voltage.
Attention, consult ACCOMPANYING DOCUMENTS.
Follow operating instructions or Consult instructions for use.
STAND-BY (Orange Light)
Direct current.
UL Mark
Authentication sign of Standard Inspection Bureau
for U.S.A
Complies with ANSI/AAMI ES60601-1 and CSA
C22.2 No. 60601-1

8
Troubleshooting
No Power LED Indicator
Check if power cord and adapter is plugged.
Power Button Not Working
Check the certified technician
Brightness Buttons Not Working
Check if the MAX or MIN level is reached.
Volume Buttons Not Working
Check if the MAX or MIN level is reached.
Check audio setting in the operating system.
No Display
Check the graphic driver setting to see if the correct video output
device is selected.
Touch Screen Not Responding
Contact your certified technician.
Touch Screen Not Working
Correctly
Use software tool on the operating system to calibrate the touch
screen and make it accurate. Or contact the technician to calibrate
for you.
System Speakers Not Working
Check if the audio driver is properly installed in the operating system.
Check if the volume setting reaches MAX or MIN in the operating
system.
Camera Fails to Work
Contact your certified technician.
Other peripherals Not Working
Contact your certified technician.
Earphone Not Working
Check audio setting in the operating system.
USB Port Not Working
Unplug the peripheral and try again. Reboot the system if necessary.
Microphone Not Working
Check audio setting in the operating system.
System Fails to Boot up
Could be memory or storage failure. Contact your certified
technician.
System freezes
Press the power button for 5 seconds to force the system reboot.
[Note]
If you cannot get the system back to work, please contact the certified technician for
further inspection or return for repair service. Do not open the system by yourself if you
are not a certified technician.

9
Disposing of Your Old Product
WEEE Mark (European Directive 2002/96/EC)
Within the European Union
EU-wide legislation, as implemented in each Member State, requires
that waste electrical and electronic products carrying the mark (left)
must be disposed of separately from normal household waste. This
includes monitors and electrical accessories, such as signal cables
or power cords. When you need to dispose of your display products,
please follow the guidance of your local authority, or ask the shop
where you purchased the product, or if applicable, follow any
agreements made between yourself and Avalue.
The mark on electrical and electronic products only applies to the
current European Union Member States.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. ONLY A
CERTIFIED SERVICE TECHNICIAN IS AUTHORIZED TO REPLACE THE BATTERY. DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS.

10
System and Adapter Specifications
System Specifications
Display
17.3”TFT-LCD 1920x1080 LED Backlight
Touch Screen
5-Wire Resistive Touch Panel
Processor
Intel 2nd Generation Core i7-2610UE1.5GHz/2340UE
1.3GHz/Celeron1.4GHz
Chipset
Intel QM67
Memory
2~16GB DDR3 1066/1333MHz SODIMM
Storage
2.5”SATA HDD/SSD
Expansion
1 x USB mini Card Socket
3 x mini-PCIe Card Sockets
Rating
19V 3.15A
Power Consumptions
40W (MAX)
Environmental Specifications
Operating Temperature
0~40 degrees (C) or 41~104 degrees (F)
Operating Humidity
20~80% Relative Humidity, Non-Condensing
Operating Altitude
-380m to 3,000m or -1,246 feet to 9,842 feet
Operating Atmospheric
Pressure
700hPa to 1060hPa
Transport / Storage
Temperature
-20~65 degrees (C) or -4~149 degrees (F)
Transport / Storage
Humidity
10~90% Relative Humidity, Non-Condensing
Transport / Storage
Altitude
-380m to 12,000m or -1,246 feet to 39,370 feet
Transport / Storage
Atmospheric Pressure
200hPa to 1060hPa
Vibration
1.5G
Adapter Specifications
Manufacturer
Adapter Technology Co., LTD
Model
ATM065-A190
Input
100~240V~50-60Hz 1.6-0.7A
Output
19V DC 3.43A

11
EMC Table
Guidance and manufacturer’s declaration – electromagnetic emissions
The model AID-173SHR is intended for use in the electromagnetic environment specified below. The customer or
the user of the model AID-173SHR should assure that it is used in such an environment.
Emissions test
Compliance
Electromagnetic environment –
guidance
RF emissions
CISPR 11
Group 1
The model AID-173SHR uses RF energy
only for its internal function. Therefore, its
RF emissions are very low and are not likely
to cause any interference in nearby
electronic equipment.
RF emissions
CISPR 11
Class B
The model AID-173SHR is suitable for use
in all establishments, including domestic
establishments and those directly
connected to the public low-voltage power
supply network that supplies buildings used
for domestic purposes.
Harmonic emissions
IEC 61000-3-2
Class A
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Complies
Recommended separation distances between
portable and mobile RF communications equipment and the model AID-173SHR
The model AID-173SHR is intended for use in an electromagnetic environment in which radiated RF disturbances
are controlled. The customer or the user of the model AID-173SHR can help prevent electromagnetic interference
by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and
the model AID-173SHR as recommended below, according to the maximum output power of the communications
equipment.
Rated maximum output
power of transmitter
W
Separation distance according to frequency of transmitter
m
150 kHz to 80 MHz
d = 1,2
P
80 MHz to 800 MHz
d = 1,2
P
800 MHz to 2,5 GHz
d = 2,3
P
0,01
0,12
0,12
0,23
0,1
0,38
0,38
0,73
1
1,2
1,2
2,3
10
3,8
3,8
7,3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in
metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the
maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.

12
Guidance and manufacturer’s declaration – electromagnetic immunity
The model AID-173SHR is intended for use in the electromagnetic environment specified below. The customer or
the user of the model AID-173SHR should assure that it is used in such an environment.
Immunity test
IEC 60601
test level
Compliance level
Electromagnetic
environment –
guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
6 kV contact
8 kV air
6 kV contact
8 kV air
Floors should be wood,
concrete or ceramic tile. If
floors are covered with
synthetic material, the relative
humidity should be at least 30
%.
Electrical fast
transient/burst
IEC 61000-4-4
2 kV for power
supply lines
1 kV for input/output
lines
2 kV for power
supply lines
1 kV for input/output
lines
Mains power quality should
be that of a typical
commercial or hospital
environment.
Surge
IEC 61000-4-5
1 kV line(s) to line(s)
2 kV line(s) to earth
1 kV line(s) to line(s)
2 kV line(s) to earth
Mains power quality should
be that of a typical
commercial or hospital
environment.
interruptions and
voltage variations
on power supply
input lines
IEC 61000-4-11
<5 % UT
(>95 % dip in UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
<5 % UT
(>95 % dip in UT)
for 5 sec
<5 % UT
(>95 % dip in UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
<5 % UT
(>95 % dip in UT)
for 5 sec
Mains power quality should
be that of a typical
commercial or hospital
environment. If the user of the
model AID-173SHR requires
continued operation during
power
mains interruptions, it is
recommended that the model
AID-173SHR be powered
from an uninterruptible power
supply or a battery.
Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
3 A/m
3 A/m
Power frequency magnetic
fields should be at levels
characteristic of a typical
location in a typical
commercial or hospital
environment.
NOTE UT is the a.c. mains voltage prior to application of the test level.

By Jason Lin
Guidance and manufacturer’s declaration – electromagnetic immunity
The model AID-173SHR is intended for use in the electromagnetic environment specified below. The
customer or the user of the model AID-173SHR should assure that it is used in such an environment.
Immunity test
IEC 60601
test level
Compliance
level
Electromagnetic
environment –guidance
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3 Vrms
150 kHz to 80
MHz
3 V/m
80 MHz to 2,5
GHz
3 Vrms
3 V/m
Portable and mobile RF
communications equipment
should be used no closer to
any part of the model
AID-173SHR, including
cables, than the
recommended separation
distance calculated from the
equation applicable to the
frequency of the transmitter.
Recommended separation
distance
d = 1,2
P
d = 1,2
P
80 MHz to 800
MHz
d = 2,3
P
800 MHz to 2,5
GHz
where P is the maximum
output power rating of the
transmitter in watts (W)
according to the transmitter
manufacturer and d is the
recommended separation

AID-173SHR Quick Reference Guide
AID-173S Quick Reference Guide
14
distance in metres (m).
Field strengths from fixed RF
transmitters, as determined
by an electromagnetic site
survey, ashould be less than
the compliance level in each
frequency range. b
Interference may occur in the
vicinity of equipment marked
with the following symbol:
NOTE 1At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption
and reflection from structures, objects and people.
aField strengths from fixed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast
cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to
fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field
strength in the location in which the model AID-173SHR is used exceeds the applicable RF
compliance level above, the model AID-173SHR should be observed to verify normal operation. If
abnormal performance is observed, additional measures may be necessary, such as reorienting or
relocating the model AID-173SHR.
bOver the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

AID-173SHR Quick Reference Guide
AID-173S Quick Reference Guide
15
CONTENT
1. AID-173S Bedside Terminals Features.........................................................16
1.1 Front Look.......................................................................................17
1.2 Rear & Bottom Look.......................................................................18
1.3 Handset............................................................................................19
2. Setting Up AID-173S Bedside Terminals......................................................20
2.1 Mounting..........................................................................................21
2.2 Cabling.............................................................................................22
2.3 System Activation & Registration .................................................23
2.4 Connecting to the Internet.............................................................24
3. Using AID-173S Bedside Terminals...............................................................25
3.1. Turn ON/OFF the System ..............................................................26
3.2 Using LCD Display and Touch Screen..........................................27
3.3Using Earphone and Microphone ..................................................28
3.4 Using the Smart Card Reader........................................................29
3.5 Using Magnetic Stripe Reader.......................................................30
3.6 Using RFID Reader/Writer..............................................................31
3.7 Using Handset.................................................................................32
3.8 Using Barcode Scanner .................................................................34
4. Upgrading AID-173S Bedside Terminals..................................................36
4.1 Adding/Removing/Replacing Memory ..........................................37
4.2 Removing and Replacing the Wireless Card................................38
4.3 Adding 3rd Party Mini-PCIe Cards ................................................39
4.4 Removing and Replacing the Hard Disk Drive.............................40
.

AID-173SHR Quick Reference Guide
AID-173S Quick Reference Guide
16
1. AID-173SHR Bedside Terminals Features
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
In this chapter, you will learn all of the features of AID-173SHR
bedside terminals.
1.1 Front Look
1.2 Rear & Bottom Look
1.3 Handset

AID-173SHR Quick Reference Guide
AID-173S Quick Reference Guide
17
1.1 Front Look
Camera
Handset
Magnetic Stripe Reader
Smart Card Reader
RFID Reader/Writer
17.3”TFT-LCD & Touch Screen
Cord
3 x USB
Volume
Up/down
Brightness
Up/down
Reserved
Power on/off
Handle

AID-173SHR Quick Reference Guide
AID-173S Quick Reference Guide
18
1.2 Rear & Bottom Look
Microphone
Service Door
COM1
Speaker
Speaker
HDMI Output
DP Output
TV Antenna Input (optional)
USB Port
DC in
LAN
COM2
Nursing Call Input
BNC Video Input (Optional)

AID-173SHR Quick Reference Guide
AID-173S Quick Reference Guide
19
1.3 Handset
Key
Descriptions
Activate the phone software (i.e. Skype)
Nurse Call
Answer
Hang Up
Contact List Up
Contact List Down
~
Numeric Keys
* Key
# Key
Barcode Scanner
Scan button
Volume
Volume
Scan button

AID-173SHR Quick Reference Guide
AID-173S Quick Reference Guide
20
2. Setting Up AID-173SHR Bedside Terminals
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
In this chapter, you will learn how to set upAID-173SHR bedside
terminal hardware and cable connection. Finally, with Internet ISP
setting information, you will be able to connect AID-173SHR
bedside terminal to the Internet.
2.1 Mounting
2.2 Cabling
2.3 System Activation & Registration
2.4 Connecting to the Internet