Avaya WAP9112 Instruction Manual

NN47252-304 Issue 01.01
Installing the Avaya WLAN Indoor Wall Access Point WAP9112
The Avaya WAP 9112 is a 2x2 802.11ac indoor wall access point (AP) with two fixed-band radios: one at 5 GHz and
one at 2.4 GHz. It includes an Ethernet wall switch with four 10/100/1000 ports, one of which may supply power.
Preparation
Run a data uplink cable (Cat5e/Cat6) for the single Gigabit uplink port.
Supply power—typically via IEEE 802.3af/at Power over Ethernet (PoE) on the same cable as the data uplink.
See Figure 2 on the next page for Uplink PoE and Pass-though ports. 
The total PoE uplink cable length must be no more than 100 m, including all cable segments. The WAP must be
connected to PoE networks without routing cables to the outside plant.
If you supply 802.3at PoE power to the uplink port, you may use the WAP 9112’s LAN4-PoE switch port to
supply 802.3af power and data to another device.
Alternatively, you may supply your own local 48 VDC power adapter meeting these specifications—
Pass-through port—this simply provides an Ethernet pass-through connection (with or without POE) from the
back of the unit to a port on the side of the WAP 9112.
LAN ports—these four switch ports on the bottom of the WAP 9112 allow you to provide Ethernet connectivity
to other devices. LAN4-PoE supplies 802.3af PoE, if a 48 VDC power adapter is used (Step 5 below), or if
802.3at PoE power is supplied as described above.
Wall Installation
Figure 1
Locking
tab
WAP 9112 Access Points (APs) should be mounted on an inside wall.
1. Remove the blank wall plate from the wall with a screwdriver.
2. As shown in Figure 1, feed the Uplink (PoE) and Pass-through cables
through the opening in the supplied mounting bracket and secure the
bracket to the wall using the two screw holes previously occupied by
the blank wall plate. Ensure that the “UP” label is at the top, and that
the tab for the locking screw is on the left facing towards you.
Output Power +48VDC
Nominal Load
Current 0.63A
Ripple and Noise At 20Mhz, and output parallel with 0.1uF and
10uF capacitors to ground, temperature at 25°C,
at nominal input voltage
Connector Jack Plug 55*2.5*11.5mm
Polarity

WAP 9112 Installation
2
3. Connect the cables as follows. Plug the Uplink-PoE and Pass-through cables into their respective sockets as
shown in Figure 2 (A). If the cables are not fitted with RJ45 jacks, they can be connected to the punch down
blocks using a dedicated network cable tool according to the sequence of colored wires marked on the back of
the AP, as shown in Figure 2 (B).
4. Move the AP into position against the bracket. Make sure that the locking tab mates with the locking slot as
indicated by the dotted line in Figure 2 (A). Secure the AP to the mounting bracket using the locking screw, as
shown in Figure 2 (C). The screw should be tightened to not more than 20Kgf and care should be taken not to
damage the equipment.
5. If you have not supplied power via PoE, use a local 48 VDC power adapter
(meeting the specifications on Page 1) as shown in Figure 3.
6. When the correct power is supplied, the POWER LED on the side of the unit
lights, and the WAP 9112 boots up.
Locking slot
Uplink PoE
Pass-through
Figure 2
AB
C
Install
Locking Screw
Locking tab
Figure 3

WAP 9112 Installation
NN47252-304 Issue 01.01
Provisioning and Management
WAP 9112 wireless APs are managed by the Avaya Wireless LAN Orchestration System (WOS). WAP 9112s are not
managed directly via CLI or Web Management Interface. WOS can automatically detect and provision new WAPs
deployed in your network—create and configure a default profile in WOS for newly added APs, and set up
discovery for the APs’ network. Once an installed AP has Internet connectivity, it will automatically contact WOS
for provisioning per your settings, and upgrade the AP to the latest software version as appropriate.
Manual Reset
If you need to manually reset the WAP 9112, the RESET button is located above the Pass-through port. Use a paper
clip to depress and hold the reset button (there should be a faint click). There are three actions that the WAP 9112
can perform depending on how long the button is held down:
2 second hold time—LED test: all LEDs light for ten seconds.
4 second hold time—”Soft reset”: WAP 9112 reboots and uses the last saved configuration.
10 second hold time—Factory reset: WAP 9112 reboots and restores the factory default settings.
Contact Avaya Support
See the Avaya Support website: http://support.avaya.com for Product or Hosted Service documentation, notices,
and articles, or to report a problem with your Avaya Product or Hosted Service. For a list of support telephone
numbers and contact addresses, go to the Avaya Support website: http://support.avaya.com (or such successor
site as designated by Avaya), scroll to the bottom of the page, and select Contact Avaya Support.
See the support web site for product warranty information, software license terms and information, and the latest
versions of product documentation.
Copyright 2015, Avaya, Inc.
Avaya is a registered trademark of Avaya Inc.