Avermedia AVerVision CP130 User manual

EnglishDeutschFrançais
ItalianoEspañolČesky
FCC NOTICE (Class A)
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Federal Communications Commission
Statement
NOTE- This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
tuning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/television technician
for help.
Class A ITE:
Class A ITE is a category of all other ITE which satisfies the
class A ITE limits but not the class B ITE limits. Such
equipment should not be restricted in its sale but the following
warning shall be included in the instructions for use:
Warning - This is a class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
CE Class A (EMC)
This product is herewith confirmed to comply
with the requirements set out in the Council
Directives on the Approximation of the laws of
the Member States relating to Electromagnetic
Compatibility Directive 2004/108/EEC.
Warning - This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures to correct this
interference.

DISCLAIMER
No warranty or representation, either expressed or implied, is
made with respect to the contents of this documentation, its
quality, performance, merchantability, or fitness for a particular
purpose. Information presented in this documentation has been
carefully checked for reliability; however, no responsibility is
assumed for inaccuracies. The information contained in this
documentation is subject to change without notice.
In no event will AVerMedia be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or
inability to use this product or documentation, even if advised of
the possibility of such damages.
TRADEMARKS
AVerVision is registered trademarks of AVerMedia Information,
Inc. IBM PC is a registered trademark of International Business
Machines Corporation. Macintosh is a registered trademark of
Apple Computer, Inc. Microsoft is a registered trademark and
Windows is a trademark of Microsoft Corporation. All other
products or corporate names mentioned in this documentation
are for identification and explanation purposes only, and may
be trademarks or registered trademarks of their respective
owners.
COPYRIGHT
©2008 by AVerMedia INFORMATION, Inc. All rights reserved.
No part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any
language in any form by any means without the written
permission of AVerMedia Information, Inc.
THE MARK OF CROSSED-OUT WHEELED
BIN INDICATES THAT THIS PRODUCT MUST
NOT BE DISPOSED OF WITH YOUR OTHER
HOUSEHOLD WASTE. INSTEAD, YOU NEED
TO DISPOSE OF THE WASTE EQUIPMENT
BY HANDING IT OVER TO A DESIGNATED
COLLECTION POINT FOR THE RECYCLING
OF WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT. FOR MORE INFORMATION
ABOUT WHERE TO DROP OFF YOUR
WASTE EQUIPMENT FOR RECYCLING,
PLEASE CONTACT YOUR HOUSEHOLD
WASTE DISPOSAL SERVICE OR THE SHOP
WHERE YOU PURCHASED THE PRODUCT.

EnglishDeutschFrançais
ItalianoEspañolČesky
T
Ta ab bl le e o of f C Co on nt te en nt ts s
Introduction ...................................................... E-1
Package Contents ............................................ E-1
Optional Accessories....................................... E-2
AVerVision CP130 Parts................................... E-3
Technical Specifications.................................. E-4
Making the Connections.................................. E-5
Connecting the Power Adapter ............................... E-6
Connecting a TV ..................................................... E-6
Connecting a VGA, Mac Display Monitor or
LCD/DLP Projector ................................................. E-7
Connecting an IBM Compatible PC or
Macintosh Computer............................................... E-7
Installing the Optional Light Box.............................. E-8
Connecting to a Microscope ................................... E-9
Setting Up AVerVision CP130.......................... E-9
Camera Head ......................................................... E-9
LED Light ................................................................ E-9
Flexible Gooseneck and Arm ................................ E-10
Anti-glare Sheet .................................................... E-10
Touch Button Control Panel.......................... E-11
OSD Navigation Tree...................................... E-13
Menu Functions.............................................. E-14
Transferring the captured image to PC........ E-17
Troubleshooting ............................................. E-17
Limited Warranty ............................................ E-18

E-1
EnglishDeutschFrançais
ItalianoEspañolČesky
P
Pa ac ck ka ag ge e C Co on nt te en nt ts s
AVerMedia®AVerVision CP130
h
s
i
l
g
n
E
h
c
s
t
u
e
D
s
i
a
ç
n
a
r
F
o
n
a
i
l
a
t
I
l
o
ñ
a
p
s
E
Čy
k
s
e
AVerMedia
®
AVerVisionCP130
UserManual
A
V
erMedia
®
DigitalDocumentCamera
User Manual
Anti-glare Sheet
Driver CD
RCA Cable
S-Video Cable
USB Cable
Computer Extension cable
(VGA Cable)
I
In nt tr ro od du uc ct ti io on n
Thank you for purchasing
the AVerMedia®
AVerVision CP130. This
document camera
displays documents,
negatives, transparencies
and 3D objects onto a TV,
LCD or DLP projector
making presentations a
snap.
AVerVision CP130 is an
ideal presentation tool for
business, academic,
medical and the scientific
community.
Power Cord
* The power cord will vary
depending on the standard
power outlet of the country
where it is sold.
Power Adapter

E-2
O Op pt ti io on na al l A Ac cc ce es ss so or ri ie es s
34mm Microscopic Adapter
28mm Microscopic Adapter
Light Box
Bag

E-3
EnglishDeutschFrançais
ItalianoEspañolČesky
A AV Ve er rV Vi is si io on n C CP P1 13 30 0 P Pa ar rt ts s
The illustrations below identify the parts of AVerVision CP130.
(
8
)
(
7
)
(5)
(3)
(4)
(6)
(1)
(2)
(
9
)
(1) Camera head
(2) LED light module
(3) Camera lens
(4) LED switch
(5) Control panel
(6) Right panel
(7) Gooseneck
(8) Rear panel
(9) Left panel
(10) Light box power
port
(11) DC 12V port
(12) Antitheft slot
(13) Camera head
holder
(14) S-Video output port
(15) Composite video
output port
(16) RGB input port
(17) RGB output port
(18) TV-RGB switch
(19) USB port
(11)
Right Panel
(13)
(10)
(12)
(14)
(15)(17)
Rear Panel
(16)
(18)
(19)
Left Panel

E-4
T
Te ec ch hn ni ic ca al l S Sp pe ec ci if fi ic ca at ti io on ns s
Image
Sensor 1/2" CMOS color image sensor
Total Pixels 850K
Frame Rate 12 fps (max.)
White Balance Auto / Manual
Exposure Auto / Manual / Flicker / Night View
Image mode Text / Graphics
Effect Color / B/W / Negative
Analog RGB output XGA 60 Hz; SVGA 60 Hz; VGA 60 Hz
Image Capture Up to 40 Frames
Optics
Lens F3.0; fl=9.6mm
Focusing Manual
Shooting Area 300mm x 225mm (max.)
Zooming Digital Zoom: 8X
Power
Power Source 100-240V ~ 4.0-4.2A, 50-60Hz
Consumption 18 Watts (lamp off); 20 Watts (lamp on)
Lighting
Lamp Type LED lamp without laser pointer
Input/Output
VGA Input 15-Pins D-sub (VGA)
VGA Output 15-Pins D-sub (VGA)
S-Video Mini-DIN Jack
Composite Video RCA Jack
USB USB2.0
DC 12V Input Power Jack
Light Box Power Jack (DC 6V Output)
Dimension
Operating 160mm x 170mm x 450mm
Folded 287.4mm x 232.5mm x 61mm
Weight 2.4 kg (about 5.3 lb)

E-5
EnglishDeutschFrançais
ItalianoEspañolČesky
M
Ma ak ki in ng g t th he e C Co on nn ne ec ct ti io on ns s
The ports on the rear, left and right panel of CP130 enable you to
connect the unit to a computer, graphics display monitor or LCD/DLP
projector, TV or other device. Illustrated below are the ports that are
located at the rear, left and right panel of CP130 with their
corresponding labels.
(5) (6)(7) (8)
(4) (9)
Rear & Left Panel
(2)(3)
(1)
Right Panel
Port Description
(1) Antitheft Slot Attach a Kensington compatible security lock or
antitheft device.
(2) Light Box Plug the optional light box into this port.
(3) DC 12V Connect the power adapter into this port.
(4) RGB INPUT Input the signal from a computer or other
sources and pass it through to the RGB Output
port only.
Connect this port to the VGA output port of the
computer.
(5) RGB OUTPUT Output the signal from the camera, RGB input
port, or the captured images from the memory on
a VGA/Mac monitor or LCD/DLP projector.
(6) VIDEO OUTPUT
(RCA/Composite)
Output the signal from the camera or the
captured images from the memory on TV or
Video equipment.
(7) S-VIDEO OUTPUT Output the signal from the camera or the
captured images from the memory on TV or
Video equipment.
(8) USB Use CP130 as a USB Camera or transfer the
captured images from CP130 memory to PC.
(9) TV-RGB switch Switch to output display video either from Video,
S-VIDEO, or RGB output port.

E-6
C
Co on nn ne ec ct ti in ng g t th he e P Po ow we er r A Ad da ap pt te er r
Connect the power adapter to a standard 100V~240V AC power source.
Power adapter
Power cord
Wall outlet
C
Co on nn ne ec ct ti in ng g a a T TV V
Locate the video, S-VIDEO or SCART RGB input port of the TV or Video
equipment (i.e., VCR) to record your presentation on a videotape and
connect it to S-VIDEO or VIDEO OUTPUT port of CP130. If you are not
sure, please refer to the user manual of the TV or Video equipment.
Make sure the TV/RGB switch is set to TV.
For better video quality, we strongly suggest using S-VIDEO
connection.
S-Video cable
S-Video to SCART cable
(not supplied)
S-VIDEO
RCA to SCART cable
(not supplied)
RCA cable
VIDEO
SCART
SCART
INPUT
Projector
Te l e v i s i o n
VCR

E-7
EnglishDeutschFrançais
ItalianoEspañolČesky
C
Co on nn ne ec ct ti in ng g a a V VG GA A, , M Ma ac c D Di is sp pl la ay y
M
Mo on ni it to or r o or r L LC CD D/ /D DL LP P P Pr ro oj je ec ct to or r
Locate the RGB (VGA) input port of the display device and connect it to
RGB OUTPUT port of CP130. If you are not sure, please refer to the
user manual of the device.
Make sure the TV/RGB switch is set to RGB.
RGB (VGA) cable
(not supplied)
MAC
LCD/DLP projector
LCD monitor
MAC monitor
Monitor Adapter
(not supplied)
CRT monitor
C
Co on nn ne ec ct ti in ng g a an n I IB BM M C Co om mp pa at ti ib bl le e P PC C o or r
M
Ma ac ci in nt to os sh h C Co om mp pu ut te er r
Locate the VGA output port of the computer or laptop to display your PC
presentation on screen and connect it to RGB INPUT port of CP130. The
video signal from the RGB INPUT port is streamed to RGB OUTPUT
port and displayed on the screen.
Computer extension cable
(VGA cable)
Computer
Laptop
MAC
Monitor Adapter
(not supplied)

E-8
C
Co on nn ne ec ct ti in ng g a a C Co om mp pu ut te er r v vi ia a U US SB B
C
Co on nn ne ec ct ti io on n
Locate the USB port of the computer or laptop and connect it to USB port
of CP130. This enables you to use CP130 as a USB Camera and to
transfer the captured images from the memory and to computer. Also
see “Transfer Image from AVerVision CP130 to PC”.
USB cable
Computer
Laptop
MAC
I
In ns st ta al ll li in ng g t th he e O Op pt ti io on na al l L Li ig gh ht t B Bo ox x
Connecting an optional light box enables you to view x-rays,
transparencies and negative slides.
Light Box
(optional)
TURN ON
PLUG
IT HERE

E-9
EnglishDeutschFrançais
ItalianoEspañolČesky
Microscopic
Adapter
Microscope
C
Co on nn ne ec ct ti in ng g t to o a a
M
Mi ic cr ro os sc co op pe e
Connecting the CP130 to a microscope
enables you to examine microscopic objects
on a big screen without straining your eyes.
S
Se et tt ti in ng g U Up p A AV Ve er rV Vi is si io on n C CP P1 13 30 0
This section provides useful tips on how to adjust the CP130 to meet
your needs.
C
Ca am me er ra a H He ea ad d
The camera head can be turned 90° to the left and right. The latch must
be pressed to open and unfold the LED light. You can also manually
adjust the focus from the focus ring to improve the quality of the pictures.
Make sure to unfold the LED light fully.
180°
Latch
Focus
Ring
90° 90°
L
LE ED D L Li ig gh ht t
The LED light provides white light and is best used when presenting in
low light conditions.
Turn OnTurn On Turn OffTurn Off

E-10
F
Fl le ex xi ib bl le e G Go oo os se en ne ec ck k a an nd d A Ar rm m
The flexible gooseneck and arm design allows you to position the
camera head from any angle.
90°
A
An nt ti i- -g gl la ar re e S Sh he ee et t
The anti-glare sheet is a special coated film that helps eliminate any
glare that maybe encountered while displaying very shiny objects or
glossy surfaces such as magazines and pictures. To use, simply place
the anti-glare sheet on top of the shiny document to reduce reflected
light.

E-11
EnglishDeutschFrançais
ItalianoEspañolČesky
T
To ou uc ch h B Bu ut tt to on n C Co on nt tr ro ol l P Pa an ne el l
The touch button control panel located on the top side of the CP130
provides quick access to commonly used functions.
(8)
(9)
(1)
(2)
(3)
(4)
(5)
(7)
(6) (11)
(10)
Function Description
(1) POWER Turn the unit on/off.
(2) Output LED
Indicator
Indicate the setting of the TV to RGB switch to which
the video signal is being sent out.
(3) Shuttle Wheel - Turn the shuttle wheel clockwise to zoom in and
counter-clockwise to zoom out the image in
Camera and Playback mode only. The image can
digitally zoom up to 800%. Press ENTER to return
to normal view (100%).
- Press the shuttle wheel ▲,▼,◄, & ►to pan the
image while in zoom in mode, to make a selection
on 16-thumbnail images or move to the next or
previous single full screen preview in Playback
mode, or to make a selection and adjustment on
the OSD main-menu and sub-menu (See Menu
Functions for more details).
(4) ENTER Make a selection in Playback mode and OSD menu.
(5) FREEZE Toggle to pause or resume the camera.
(6) MENU Pull up and exit the OSD main-menu and sub-menu.
(7) Source LED
Indicator
Indicate the source of the video signal or image.

E-12
Function Description
(8) SOURCE Switch between Camera, Playback and PC mode.
- Camera mode displays the video signal from the
built-in camera.
SLIDE SHOW
START
INTERVAL
- Playback mode displays the captured image from
the built-in memory in 16-thumbnail images. Use
▲,▼,◄, & ►buttons to make a selection and
ENTER to display the selected image in full
screen. To start slide show press MENU and
select START and press ENTER to begin and
end. Select INTERVAL to set the display time
interval between frames in second.
- PC mode displays the video signal from the RGB
INPUT port of AVerVision CP130.
(9) AUTO IMAGE Automatically adjust and set the white balance and
exposure setting.
(10) CAP/DEL - Capture a still image in Camera mode. The
captured image is saved in the built-in memory at
1024 x 768 resolution and can store up to 40
images.
- Remove the selected picture from the built-in
memory permanently in Playback mode.
(11) EFFECT Convert and display the image in BW, Negative or
Color in Camera and Playback mode only.

E-13
EnglishDeutschFrançais
ItalianoEspañolČesky
O
OS SD D N Na av vi ig ga at ti io on n T Tr re ee e
MENU
EFFECT REVERSE/MIRROR TIMER CAPTURE SETTINGS RECALL
COLOR B / W NEGATIVE
MIRROR OFF REVERSE OFF START PAUSE STOP SET TIME MODE IMAGE LANGUAGE FORMAT MEMORY USB CONNECTION SAVE SINGLE CONTINUOUS NO YES PROFILE 1 PROFILE 2 PROFILE 3
DEFAULT
INTERVAL
5 SECS
TEXT GRAPHICS
MODE
255650
RED
EXPOSURE WHITE BALANCE BRIGHTNESS CONTRAST RESOLUTION
IMAGE
AUTO RED BLUE
NO YES
FORMAT MEMORY
50 HZ 60 HZ
FLICKER
ON OFF AUTO
NIGHT VIEW
AUTO MANUAL FLICKER NIGHT VIEW
63160
2551400
ENGLISH DEUTSCH FRANÇAIS ITALIANA ESPAÑOL Русский POLSKI Čeština
LANGUAGE
USB CAMERA IMG DOWNLOAD
USB CONNECTION PROFILE 1 PROFILE 2 PROFILE 3
SAVE
1024 x 768 800 x 600 640 x 480
255650
BLUE
255650
RED
255650
RED
MANUAL
54210

E-14
M
Me en nu u F Fu un nc ct ti io on ns s
The MENU functions of CP130 enhance fine-tuning your screen display,
set the timer, select OSD language and more. Press the MENU button
to call up and exit from the main menu or sub-menu display. Then use
▲or▼buttons to select the items in the menu list. Use ►/ENTER
button to enter sub-menu and ◄/ ENTER to return to main menu. To
adjust the setting, press ◄or►buttons. To make a selection, press
ENTER.
OSD Menu Description
MENU
EFFECT
REVERSE/MIRROR
TIMER
CAPTURE
SETTINGS
RECALL
DEFAULT
COLOR
B / W
NEGATIVE
EFFECT
Press ►and use ▲or▼buttons to select and display
the image in Camera mode into positive (true color),
monochrome (black and white) or negative. Then
press ►/ENTER to make a selection.
MENU
EFFECT
REVERSE/MIRROR
TIMER
CAPTURE
SETTINGS
RECALL
DEFAULT
MIRROR OFF
REVERSE OFF
REVERSE / MIRROR
Press ►and use ▲or▼buttons to select and turn on
MIRROR to flip the image and REVERSE to rotate
the image by 180° in Camera mode. Then press
►/ENTER to make a selection.
MENU
EFFECT
REVERSE/MIRROR
TIMER
CAPTURE
SETTINGS
RECALL
DEFAULT
START
PAUSE
STOP
SET TIME
TIMER
Press ►and use ▲or▼buttons to select SET TIME
to set the time value, START to begin the countdown
timer, PAUSE/RESUME to temporarily halt or
continue, and STOP to end.
MENU
EFFECT
REVERSE/MIRROR
TIMER
CAPTURE
SETTINGS
RECALL
DEFAULT
SINGLE
CONTINUOUS
CAPTURE
Press ►and use ▲or▼buttons to select SINGLE or
CONTINUOUS capture mode.
Setting SINGLE saves one still image only and
CONTINUOUS saves successive still images until the
built-in memory is full or when the CAP/DEL button is
being press again to stop.
INTERVAL
5 SECS
In Continuous mode, use ◄or►buttons to increase
or decrease the capture time interval between frames
and then press ENTER to save the setting and exit.
The time interval can be set from 5 to 600 sec.
MENU
EFFECT
REVERSE/MIRROR
TIMER
CAPTURE
SETTINGS
RECALL
DEFAULT
MODE
IMAGE
LANGUAGE
FORMAT MEMORY
USB CONNECTION
SAVE
SETTINGS
Press ►, then use ▲or▼buttons to select the items
in SETTINGS list and press ►/ENTER.
MODE
TEXT
GRAPHICS
SETTINGS > MODE
Use ▲or▼buttons to select between Text and
Graphics enhancement mode and then ENTER to
make a selection.

E-15
EnglishDeutschFrançais
ItalianoEspañolČesky
OSD Menu Description
MODE
TEXT
GRAPHICS
•Text - corrects the intensity of the adjacent pixel
making it more uniform producing sharper and
clearer images.
•Graphics - adjusts the gradient of the adjacent
pixel making it appears to have a smooth image.
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION
AUTO
MANUAL
FLICKER
NIGHT VIEW
SETTINGS > IMAGE > EXPOSURE
Press ►and use ▲or▼buttons to select between
Auto, Manual, Flicker and Night View. Then press
►/ENTER to make a selection.
Select AUTO to automatically adjust the camera
exposure to determine how much light is required.
MANUAL
0 5421
SETTINGS > IMAGE > EXPOSURE > MANUAL
Press ►/ENTER and use ◄or►buttons to manually
adjust the exposure level then press ENTER to save
the setting and exit.
FLICKER
50 HZ
60 HZ
SETTINGS > IMAGE > EXPOSURE > FLICKER
Use ▲or▼buttons to select between 50Hz or 60Hz.
Some display devices cannot handle high refresh
rates. The image will flicker a couple of times as the
output is switched to another refresh rate.
NIGHT VIEW
ON
OFF
AUTO
SETTINGS > IMAGE > EXPOSURE > NIGHT VIEW
Use ▲or▼buttons to turn Night View ON, OFF or
AUTO.
If you are presenting in a low-light condition, Night
View enables the image of the object to appear as
though under normal lighting conditions. CP130 can
automatically adjust the exposure to compensate for
the adverse condition, but the captured image will
appear to be in slow motion.
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION
AUTO
RED
BLUE
SETTINGS > IMAGE > WHITE BALANCE
Press ►and use ▲or▼buttons to select between
Auto or manually adjust the Red and Blue color to suit
the lighting condition or color temperature. Then
press ►/ENTER to make a selection.
RED
2550 65
SETTINGS > IMAGE > WHITE BALANCE > RED
Use ◄or►buttons to manually adjust the red color
level then press ENTER to save the setting and exit.
BLUE
2550 65
SETTINGS > IMAGE > WHITE BALANCE > BLUE
Use ◄or►buttons to manually adjust the blue color
level then press ENTER to save the setting and exit.
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION 63160
SETTINGS > IMAGE > BRIGHTNESS
Use ◄or►buttons to increase or decrease the
brightness level and improve the visibility of the
image. The brightness level can be set up to 63.

E-16
OSD Menu Description
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION 2551400
SETTINGS > IMAGE > CONTRAST
Use ◄or►buttons to emphasize or reduce the
difference between light and dark conditions. The
contrast level can be adjustable up to 255.
IMAGE
EXPOSURE
WHITE BALANCE
BRIGHTNESS
CONTRAST
RESOLUTION 1024 x 768
800 x 600
640 x 480
SETTINGS > IMAGE > RESOLUTION
Press ►/ENTER and use ▲or▼buttons to choose
from different display resolutions then press
►/ENTER to make the selection.
This selection will not be available in TV output
(Composite/S-Video)
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANA
ESPAÑOL
Русский
POLSKI
Čeština
SETTINGS > LANGUAGE
Use ▲or▼buttons to select from different languages
then press ►to make the selection.
FORMAT MEMORY
NO
YES
SETTINGS > FORMAT MEMORY
Use ▲or▼buttons to select NO to exit or YES to
format and delete all the images saved in the built-in
memory then press ►/ENTER.
Please wait till the message “FORMAT” disappear to
finish the process.
USB CONNECTION
USB CAMERA
IMG DOWNLOAD
SETTINGS > USB SELECT
Use ▲or▼buttons to select the USB function
between USB Camera and Img Download.
•USB Camera - can be used as a computer
webcam or with our bundled software as video
recorder and capture still image.
•Img Download - transfer the captured images from
the built-in memory to computer hard disk.
SAVE
PROFILE 1
PROFILE 2
PROFILE 3
SETTINGS > SAVE
Use ▲or▼buttons to select which profile slot to save
your preferred setting. Only effect, mode, brightness
and contrast settings can be saved.
MENU
EFFECT
REVERSE/MIRROR
TIMER
CAPTURE
SETTINGS
RECALL
DEFAULT
PROFILE 1
PROFILE 2
PROFILE 3
RECALL
Press ►then use ▲or▼buttons to select from the
list to revert to the preferred saved profile setting and
press ►/ENTER to make the selection.
MENU
EFFECT
REVERSE/MIRROR
TIMER
CAPTURE
SETTINGS
RECALL
DEFAULT NO
YES
DEFAULT
Press ►and use ▲or▼buttons to select YES to
restore to original factory default setting or NO to exit
then press ►/ENTER to make the selection.