AVF 469097 User manual

469097 rev00
www.avfgroup.com
STOP
Read through
ALL instructions before commencing installation.
If you have any questions about this product or issues with installation, contact
the customer services helpline before returning this product to the store.
50kg
110lbs

Tools Recommended
Assembly Overview
Ø10mm (25/64”)
Masonry
Connect the TV
Fit the TV Mounting Plate
Stud Finder
Ø3mm (1/8”)
Wood
Fit the Wall Bracket
Suitable Wall Types
Solid Wall Wood Stud

Index
Measure the TV fixing holes Width and Height
1
Retain all packaging in case the product needs to be returned.
Contents may vary from photography / illustrations.
You will not need all these parts, so expect there to be some left over depending upon the
specification of your TV.
This product is intended for indoor use only. Use of this product outdoors could lead to
failure and personal injury.
It is the responsibility of the installer to ensure that the mounting wall is of a suitable
standard and void of any services (eg gas, electricity, water etc).
AVF accept no responsibility for any damage or loss caused by installing this product in a
substandard wall.
Fitting the TV Brackets
3
Fitting the Wall Bracket Covers
5
Connecting the TV
6
Fitting the Wall Bracket
4
Preparing the Wall Bracket
2
Tilt Adjustment
7

Boxed Parts
M6
16mm
T1x4
M6
30mm
T2x4
M8
25mm
T3x4
T6x4 T5x4 U1x4
C1
M8
45mm
T4x4
C2
TV Screws, Reducers and Spacers
C1
B1
B2
W1x3 W2x3
M5
S2x3
M5
S1x3
A1
A2
Xx1
WT

Measure the TV fixing holes Width and Height
1
X75 - 600mm
Y75 - 400mm
TV Fixing Holes
If width X is greater than mm or height Y greater than mm
STOP installation now and contact the customer help line.
600 400
T1/T2
M6 =
M8 = T3/T4
You are provided with diameters of TV fixing screws
Determine the screw diameter that fits and remember for step .
3
3
, M6 and M8.

Fitting the TV Brackets
3
No Spacers Spacers
For TVs with irregular / obstructed back.
For TVs with flat / unobstructed back.
T5/T6
Preparing the Wall Bracket
2
A1
A2S1S2
X

Attach the bracket to the back of your TV using suitable screw, reducer and spacer
combinations.
TV TV TVTV
WARNING
After completing step you will have fittings left over, please keep for
future reference.
3
T 1 - T 4
U
T
3
-T
4
T
1
-T
2
1
T
6
T 5
Top
Do you need
U1?
If required

Fitting the Wall Bracket
4
Solid Wall
Wood Stud
Remove Dust from Hole.
10mm (25/64")
75mm (3")
Ensure drill marks are in the centre of the wood stud.
3mm (1/8")
75mm (3")
WT
WT

DO NOT overtighten screws.
Tighten screws by hand only.
12.5mm (½”)
MAX
W1
W2
W1x3 W2x3
Lubricate screw thread with soap.
DO NOT overtighten screws.
Tighten screws by hand only.
W1
W1x3
Lubricate screw thread with soap.

Fitting the Wall Bracket Covers
5
C2
C1
C1
Connecting the TV
6
Hanging the TV

DO NOT overtighten
Adjust screws to achieve perfect tilt resistance if required.
Tilt Adjustment
7
x4
Locking the TV

STOP
Read through instructions before commencing installation.
If you have any questions about this product or issues with installation contact
the customer services helpline before returning this product to the store.
ALL
www.avfgroup.com 469100 rev00

Tools Recommended
Boxed Parts
SE
SD
SC
SB
SA SA
SB
SE
SD
SC

M5
12mm
M4
12mm
M5
10mm
M6
10mm
M6
12mm
M8
10mm
M8
12mm
SF x2
SJ1x2
SG x2 SH x2 SI1x4
SI2x2 SJ3x2 SJ4x4
SJ6x2 SJ7x2 SJ9x2 SJ10 x2
SK x2 SL x4 SM x2 SN x2

Introduction
Before you begin please take time to read through this introduction and instructions to
familiarise yourself with the product and to also help you select the best way to attach
your Soundbar. This instruction manual covers many different configurations and is very
comprehensive. Please do not be put off by this as you will only need to follow a few steps.
This introduction gives you a basic idea as to what steps are involved in mounting your
Soundbar to your TV.
X1
X2
X3
Measure your TV and Soundbar fixing holes
Prepare the Soundbar Mount Bracket

Before you start to mount your Soundbar to your TV you will need to decide if you are
going to mount your Soundbar above your TV or below your TV.
Mounting Above Follow steps 3 to 7 Mounting Below Please go to step 8
You will then need to attach the Soundbar to your TV. See below for a description of the different
fixing methods available.
Screwing to the Back of the Soundbar
Use this method if you have no clashes with the TV and Soundbar fixing holes.
Screwing to the Bottom of the Soundbar
Use this method if you have no clashes with the TV and Soundbar fixing holes.
Attaching the Soundbar with Hook and Loop
Use this method if your Soundbar has no fixing holes or if there are clashes.
Attaching the Soundbar with Manufacturers Bracket
Use this method if a Bracket is supplied by the Manufacturer. You will also find more
information in the Manufacturers instructions.
Attaching the Soundbar with Keyhole Pin
Use this method if your Soundbar has Keyhole fixing holes.
Mounting Above or Below?

Measure your TV and Soundbar fixing holes
1
Measure the width of the fixing holes on the back of your TV (X1) and the back or bottom of
your Soundbar (X2) or the length of your Soundbar (X3) if it has no fixing holes.
If your TV fixing holes and Soundbar fixing holes are equal you will not be able to screw
directly to the back or bottom of your Soundbar. In this case you will need to use a different
method for attaching.
Before you attach horizontal bracket SB to vertical bracket SA use measurements X1 and X2
or X1 and X3 to decide the best configuration. Please see below for examples.
Examples below show soundbar with fixing holes.
X1
X2
X3
300mm 200mm
X1X1
700mm
X2
300mm
X2
SA
SB
SA
SB
SA SA
SB

Prepare the Soundbar Mount Bracket
2
Use measurements X1 & X2 or X3 from Step 1
300mm
X1
800mm
X3
Examples below shows soundbar with no fixing holes.
SH x2
SH
SH
SA
SB
SA
SB
SA
SB
SB
SA

You only need to follow one of steps 3 to 7 if you have chosen to have your Soundbar
mounted above your TV.
Please select your method of attaching your Soundbar to your TV and follow the
appropriate steps.
Screwing to the Back of the Soundbar
Screwing to the Bottom of the Soundbar
Attaching the Soundbar with Hook and Loop
Attaching the Soundbar with Manufacturers Bracket
Attaching the Soundbar with Keyhole Pin
- Step 3
- Step 4
- Step 5
- Step 6
- Step 7
Mounting Above
Before you start to mount your Soundbar to your TV you will need to decide if you are
going to mount your Soundbar above your TV or below your TV.
Mounting Above Follow steps 3 to 7 Mounting Below Please go to step 8
Mounting Above or Below?

Screwing to the Back of the Soundbar
3
Attach the brackets to the back of your Soundbar using suitable screw and reducer combinations.
Screw diameter
dependant
Please use this step in conjunction
with the instructions provided with
your TV wall mount.
The brackets and the screws
shown in grey are only an example.
These are supplied by the TV
wall mount manufacturer.
SJ1x2
SI2x2
SI1x2
SF x2 SF x2 SF x2 SF x2
SJ4x2
SI1x2 SI1x2
SJ10 x2
SJ7x2
SJ1/SJ4/SJ7/SJ10
SI2SI1
SF
SN