Avid Technology Mbox Mini User manual

Mbox Mini User Guide
Version 9.0
®

Legal Notices
This guide is copyrighted ©2010 by Avid Technology, Inc.,
(hereafter “Avid”), with all rights reserved. Under copyright
laws, this guide may not be duplicated in whole or in part
without the written consent of Avid.
003, 96 I/O, 96i I/O, 192 Digital I/O, 192 I/O, 888|24 I/O,
882|20 I/O, 1622 I/O, 24-Bit ADAT Bridge I/O, AudioSuite,
Avid, Avid DNA, Avid Mojo, Avid Unity, Avid Unity ISIS,
Avid Xpress, AVoption, Axiom, Beat Detective, Bomb Factory,
Bruno, C|24, Command|8, Control|24, D-Command, D-Control,
D-Fi, D-fx, D-Show, D-Verb, DAE, Digi 002, DigiBase,
DigiDelivery, Digidesign, Digidesign Audio Engine, Digidesign
Intelligent Noise Reduction, Digidesign TDM Bus, DigiDrive,
DigiRack, DigiTest, DigiTranslator, DINR, D-Show, DV Toolkit,
EditPack, Eleven, EUCON, HD Core, HD Process, Hybrid,
Impact, Interplay, LoFi, M-Audio, MachineControl, Maxim,
Mbox, MediaComposer, MIDI I/O, MIX, MultiShell, Nitris, OMF,
OMF Interchange, PRE, ProControl, Pro Tools M-Powered,
Pro Tools, Pro Tools|HD, Pro Tools LE, QuickPunch, Recti-Fi,
Reel Tape, Reso, Reverb One, ReVibe, RTAS, Sibelius,
Smack!, SoundReplacer, Sound Designer II, Strike, Structure,
SYNC HD, SYNC I/O, Synchronic, TL Aggro, TL AutoPan,
TL Drum Rehab, TL Everyphase, TL Fauxlder, TL In Tune,
TL MasterMeter, TL Metro, TL Space, TL Utilities, Transfuser,
Trillium Lane Labs, Vari-Fi, Velvet, X-Form, and XMON are
trademarks or registered trademarks of Avid Technology, Inc.
Xpand! is Registered in the U.S. Patent and Trademark Office.
All other trademarks are the property of their respective
owners.
Product features, specifications, system requirements, and
availability are subject to change without notice.
Guide Part Number 9329-65069-00 REV A 9/10
Documentation Feedback
At Avid, we are always looking for ways to improve our
documentation. If you have comments, corrections, or
suggestions regarding our documentation, email us at
[email protected].

Contents iii
contents
Chapter 1. Welcome to Mbox Mini . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Mbox Mini Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
System Requirements and Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Conventions Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
About www.avid.com . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chapter 2. Mbox Mini Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mbox Mini Front Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Mbox Mini Back Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 3. Installing and Connecting Mbox Mini. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 4. Making Studio Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting Audio Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connecting a Microphone to Mbox Mini . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting Instruments to the Mbox Mini . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Chapter 5. Using the Driver Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Setting Sample Rate and Buffer Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Viewing Firmware and Installer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Appendix A. Using Third-Party Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Configuring Mbox Mini for Third-Party Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Configuring the Apple Sound Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Mbox Mini User Guideiv
Appendix B. Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
EMC (Electromagnetic Compliance) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Safety Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Chapter 1: Welcome to Mbox Mini 1
chapter 1
Welcome to Mbox Mini
Welcome to the Mbox®Mini USB audio inter-
face from Avid®.
Mbox Mini provides your USB-equipped com-
puter with two channels of analog audio input,
two analog monitor outputs, and one head-
phone output. Mbox Mini includes one profes-
sional-quality mic preamp and 24-bit analog-to-
digital and digital-to-analog converters.
Mbox Mini integrates with Pro Tools® software,
and is compatible with third-party audio appli-
cations that support the CoreAudio (Mac) or
ASIO (Windows) standard.
Mbox Mini Features
The Mbox Mini provides the following:
• Two channels of analog audio input:
• Combo connector with XLR (microphone)
input and 1/4-inch (line-level) input and
switchable 48V phantom power
• Two 1/4-inch TRS (Tip-Ring-Sleeve) con-
nectors. One input is switchable between
Line and DI level devices. The other is DI
only and switchable with the Combo con-
nector for Input 1
• Gain control with –20 dB pad available sep-
arately on each input channel
• Two 1/4-inch TRS analog monitor outputs
• 1/4-inch (TRS) stereo headphone output with
adjustable level control
• Mon (Monitor) Mute switch for muting mon-
itor outputs, without muting headphone out-
put. This switch does not affect recording
• 24-bit A/D and D/A converters, supporting
sample rates of 44.1 kHz and 48 kHz
• Zero-latency analog record monitoring with
Mix (ratio) knob for adjustable balance be-
tween input and playback
• USB-powered operation
Mbox Mini may not function properly if con-
nected to a USB hub. Connect Mbox Mini to a
separate, dedicated USB port.

Mbox Mini User Guide2
System Requirements and
Compatibility
Mbox Mini can be used with a qualified Win-
dows or Mac computer running Pro Tools soft-
ware 8.0.4 or higher.
Mbox Mini can be also be used with a qualified
Mac or Windows computer running any other
Core Audio- or ASIO-compliant software.
Mbox Mini hardware drivers must be installed
before you can connect and use your
Mbox Mini.
A DVD drive is required to use the Drivers In-
staller disc (included with your Pro Tools soft-
ware package).
Avid can only assure compatibility and provide
support for hardware and software it has tested
and approved.
For complete system requirements and a list of
qualified computers, operating systems, hard
drives, and third-party devices, visit:
www.avid.com/compatibility
Conventions Used in This
Guide
All of our guides use the following conventions
to indicate menu choices and key commands:
:
The names of Commands, Options, and Settings
that appear on-screen are in a different font.
The following symbols are used to highlight
important information:
For Pro Tools installation instructions, see
the Pro Tools Installation Guide.
For Mbox hardware drivers installation in-
structions, see Chapter 3, “Installing and
Connecting Mbox.”
Convention Action
File > Save Choose Save from the
File menu
Control+N Hold down the Control key
and press the N key
Control-click Hold down the Control key
and click the mouse button
Right-click Click with the right
mouse button
User Tips are helpful hints for getting the
most from your system.
Important Notices include information that
could affect your data or the performance of
your system.
Shortcuts show you useful keyboard or
mouse shortcuts.
Cross References point to related sections in
this guide and other Pro Tools guides.

Chapter 1: Welcome to Mbox Mini 3
About www.avid.com
The Avid website (www.avid.com) is your best
online source for information to help you get
the most out of your Pro Tools system. The fol-
lowing are just a few of the services and features
available.
Product Registration Register your purchase
online.
Support and Downloads Contact Avid Customer
Success (technical support); download software
updates and the latest online manuals; browse
the Compatibility documents for system re-
quirements; search the online Knowledge Base
or join the worldwide Pro Tools community on
the User Conference.
Training and Education Study on your own using
courses available online or find out how you can
learn in a classroom setting at a certified
Pro Tools training center.
Products and Developers Learn about Avid
products; download demo software or learn
about our Development Partners and their
plug-ins, applications, and hardware.
News and Events Get the latest news from Avid
or sign up for a Pro Tools demo.

Mbox Mini User Guide4

Chapter 2: Mbox Mini Hardware Overview 5
chapter 2
Mbox Mini Hardware Overview
Mbox Mini Front Panel Features
Figure 1 identifies controls, indicators, and input and output ports on the front panel on the
Mbox Mini.
Gain/–20 dB Pad Switches 1
This knobs adjusts the gain level for Inputs 1
(Mic/Line or DI) depending on which input is
enabled by the back panel Combo/DI switch.
Turn the knob clockwise to increase gain, and
counter-clockwise to decrease gain. If your input
signal is too hot even with the Gain knob at a
low setting, pull the Gain knob out to engage a
“pad” that attenuates the signal by -20dB.
Gain/–20 dB Pad Switch 2
This knob adjusts the input gain level of Input 2
(Line/DI) depending on which input is enabled
by the back panel Line/DI switch. Turn the knob
clockwise to increase gain, and counter-clock-
wise to decrease gain. If your input signal is too
hot even with the Gain knob at a low setting,
pull the Gain knob out to engage a “pad” that
attenuates the signal by –20dB.
Figure 1. Mbox Mini front panel
Signal Clip
Headphone
output
LEDs
Signal Clip
LEDs
Gain/–20 dB pad switches 1–2 Mon/Mute
switch Master monitor
knob
Power
LED
Mix (Ratio)
Phantom power
(+48V) LED

Mbox Mini User Guide6
Signal/Clip LEDs
These LEDs illuminate green in the presence of
audio signal, and illuminate red if the input sig-
nal has clipped (overloaded) the input of the
Mbox. Clipping the input can result in audible
distortion.
Phantom Power (48V) LED
When lit, the phantom power 48V LED indi-
cates that phantom power is engaged. The
switch for phantom power is on the back of the
device. See “Phantom Power (48V) Switch” on
page 8.
Mix (Ratio)
Mbox Mini gives you the ability to monitor
your analog input signals while recording, with-
out the delay incurred by analog-to-digital and
digital-to-analog converters and host-based pro-
cessing.
This zero-latency analog monitoring is con-
trolled with the Mix knob, which you can use to
blend and adjust the monitor ratio between
Mbox Mini analog inputs and playback from
your audio application.
To listen to just the source input signal, turn the
Mix knob fully left to Input. To listen your audio
application’s output only, turn the knob fully
right.
The output from the Mix control is routed di-
rectly to the Monitor Outputs, and is mirrored
in the Headphone output.
This ability to blend and control the relative lev-
els of playback from your DAW and latency-free
live analog inputs can be particularly effective
when overdubbing.
Speaker/Mute Switch
This switch mutes the Monitor Outputs, with-
out muting the Headphone Output. This switch
does not affect recording.
Master Monitor Knob
The Master Monitor knob controls the Monitor
output and headphone output levels.
Headphone Output
Use the Headphone Output to connect stereo
headphones with a 1/4-inch stereo connector.
The headphone outputs mirror the signal sent
to the Monitor Outputs.
Power LED
The Power LED indicates that the Mbox Mini
has received power from its USB connection.
Once the Power LED light is on, audio can pass
in or out of the system.
In Pro Tools, this is the signal that is routed
to Outputs 1–2. For more information on
signal routing in Pro Tools, see the Intro to
Pro Tools Guide or the Pro Tools Reference
Guide.

Chapter 2: Mbox Mini Hardware Overview 7
Mbox Mini Back Panel Features
The Mbox Mini back panel has the following features:
Mic/Line (Input 1)
The channel 1 Mic/Line input on the back panel
provides Mic (XLR) and Line (1/4-inch Tip-Ring-
Sleeve) on a combination jack. Switch between
channel 1 Mic/Line and channel 1 DI using the
Combo/DI switch on the back panel.
DI (Input 1)
The DI input accepts instrument-level 1/4-inch
TS (Tip-Sleeve) connections.
On the front panel, the input signal is adjusted
by the Input 1 Gain control. The source
(Mic/Line or DI) is chosen using the Combo/DI
switch on the back panel.
Combo/DI Switch
This switch selects either the Mic/Line input for
channel 1 or the DI input for channel 1. When
pressed in, the channel 1 DI input is selected.
When not pressed in, the channel 1 combina-
tion jack connector is selected.
Line/DI (Input 2)
The Line/DI input accepts line level signals, in-
struments, and other 1/4-inch TRS or TS connec-
tions.
On the front panel, the input signal is adjusted
by the Input 2 Gain control. The source (Line or
DI) is chosen using the Line/DI switch on the
back panel.
Figure 2. Mbox Mini back panel
USB port Mic/Line input 1
Phantom power (+48V) switch
Monitor outputs
Line/DI switch
Line/DI
Input 2
Combo/DI switch
DI input

Mbox Mini User Guide8
Line/DI Switch
This switch selects either the line-level input or
instrument-level input for channel 2. When
pressed in, the instrument-level input (DI) is en-
abled. When not pressed in, line-level input is
enabled.
Monitor Outputs
These outputs support balanced TRS or unbal-
anced TS 1/4-inch connections. To monitor
your mix, these outputs can be connected to a
mixing board, directly to a monitoring system
such as a powered speakers or a power amp, or
another destination.
Phantom Power (48V) Switch
When pressed in, 48V phantom power is active
on the Mic XLR input. Phantom power is pro-
vided for microphones that require it to operate.
About Phantom Power
Dynamic microphones (such as a Shure SM57 or
an M-Audio Aries) do not require phantom
power to operate, but are not harmed by it. Most
condenser microphones (like an M-Audio Solaris)
do require phantom power to operate.
If you are not sure about the phantom power re-
quirements for your microphone, consult your
microphone’s documentation or contact the
manufacturer.
USB Port
This standard USB connector is used to connect
your computer to the Mbox Mini. One standard
USB cable is included with your system.
When using Pro Tools, these outputs receive
the signal that is routed to Outputs 1–2. For
more information on signal routing in
Pro Tools, see the Intro to Pro Tools Guide
or the Pro Tools Reference Guide.
Although phantom power can be used
safely with most microphones, it is possible
to damage some ribbon microphones with
it. Always turn off phantom power and wait
at least ten seconds before connecting or dis-
connecting a ribbon microphone.
When using phantom power, Mbox Mini’s
maximum current per microphone is 4 mA.

Chapter 3: Installing and Connecting Mbox Mini 9
chapter 3
Installing and Connecting Mbox Mini
To use Mbox Mini with Pro Tools or any other
CoreAudio- or ASIO-compatible applications,
you must install the Mbox Mini hardware driv-
ers on your computer.
This chapter provides instructions on installing
the drivers on Mac and Windows, and connect-
ing the Mbox Mini to your computer.
To install the drivers and connect the Mbox Mini:
1 Make sure you are logged in as an Administra-
tor for the account where you want to install the
drivers.
2 Do one of the following:
• Insert the Drivers Installer disc that came
with your Pro Tools software package into
your computer.
– or –
• Download the Mbox Mini drivers installer
for your computer platform from
www.avid.com. After downloading, make
sure the installer is uncompressed (.dmg on
Mac or .ZIP on Windows).
3 Do one of the following:
• On Mac, locate and double-click
Avid Mbox Mini.mpkg.
– or –
• On Windows, locate and double-click
Install Avid Mbox Mini.exe.
4 Follow the on-screen instructions to proceed
with installation.
5 When installation is complete, click Restart.
Do not start this procedure with your Mbox
connected to your computer.
Before installing the hardware drivers, refer
to the Read Me information included with
the drivers installer for your device.
For details on Administrator privileges, see
the documentation for your computer.

Mbox Mini User Guide10
6 After the computer has restarted, connect the
small end of the included USB cable to the USB
port on Mbox Mini and connect the other end
to any available USB port on your computer.
You can now use your Mbox Mini with
Pro Tools or any other CoreAudio- or ASIO-com-
patible applications.
If the USB LED on the front panel of the
Mbox Mini does not illuminate, try unplug-
ging the USB cable from the Mbox USB port,
and plugging it back in. If the USB LED still
does not illuminate, shut down the com-
puter, disconnect Mbox and start the com-
puter. Once the computer has fully re-
started, reconnect Mbox.
Mbox Mini may not function properly if
connected to a USB hub. If you need to use a
hub for other USB peripherals, connect the
hub to a separate USB port; Mbox must be
connected to a dedicated port on the com-
puter in order to function properly.
For Pro Tools installation instructions, see
the Pro Tools Installation Guide.

Chapter 4: Making Studio Connections 11
chapter 4
Making Studio Connections
This chapter provides step-by-step instructions
for connecting mics, instruments, mixers,
headphones, speakers, and other devices to
Mbox Mini.
Connecting Outputs
To hear audio from Mbox Mini, you need to
connect headphones or an external sound sys-
tem (such as powered monitors or a home ste-
reo) to Mbox Mini.
Connecting Headphones
You can use headphones equipped with a
1/4-inch stereo jack to monitor your audio.
To connect headphones:
1 Connect headphones with a 1/4-inch stereo
connector (or adapter) to the Headphone jack.
2 Adjust the volume using the Headphone Vol-
ume knob on the front panel.
The headphone outputs mirror the signal sent
to the Monitor Outputs.
Headphone jack on front of Mbox Mini
1/4-inch
Headphone jack
Headphone level

Mbox Mini Setup Guide12
Connecting a Sound System
The Monitor Outputs on the back of Mbox Mini
support 1/4-inch plugs. These connections can
be balanced, TRS (Tip-Ring-Sleeve) style connec-
tors, or unbalanced TS (Tip-Sleeve) connectors
(such as those on instrument cables). To listen
to your to audio, connect these outputs to any
amplification system: powered speakers, a home
stereo system, or an audio mixer.
To connect a sound system:
For stereo monitoring, connect Monitor Out-
puts 1 and 2 to the inputs of your main left and
right speakers.
To connect to a stereo system:
When connecting to a stereo system, connect
the left channel of the stereo (often the white
plug) to Monitor Output 1, and the right chan-
nel of the stereo (often the red plug) to
Monitor Output 2.
Connecting Audio Inputs
Mbox Mini inputs (sources) support micro-
phones, guitars, keyboards, and other types of
instruments. For information about connecting
specific audio sources, see “Connecting a Micro-
phone to Mbox Mini” on page 13, and “Con-
necting Instruments to the Mbox Mini” on
page 14.
Overview of Analog Inputs
Mbox Mini provides a total of two channels of
analog input on the back panel. These jacks are
labeled Mic/Line and DI (input 1) and Line/DI
(input 2).
Mic/Line (Input 1)
Input 1 provides Mic/Line and DI input connec-
tors. Inputs are selectable with the back panel
Combo/DI switch. When the Combo/DI switch
is pressed in, the DI input is selected (the DI in-
put jack is located above the Line/DI jack.).
When not pressed in, the combo connector
jacks (XLR, 1/4-inch) are selected.
Mic For XLR microphone cables.
Line (TRS or TS) For 1/4-inch Tip-Ring-Sleeve or
Tip-Sleeve cables from keyboards, mixers, and
other line-level sources.
Line/DI (Input 2)
Input 2 provides a Line/DI input connector. The
input is selectable with the back panel Line/DI
switch (located to the upper-left of the input).
This input appears as Analog In (2) in Pro Tools.
DI For 1/4-inch Tip-Sleeve cables from guitar,
bass, or similar sources.
Stereo output from the Mbox Mini (back panel)
Home stereo systems often use RCA connec-
tors. You can use an adaptor or a special ca-
ble to convert from the 1/4-inch TRS connec-
tors used by Mbox to the RCA connectors on
your home stereo.
Line Out Left
Line Out Right

Chapter 4: Making Studio Connections 13
Connecting a Microphone to
Mbox Mini
Mic Cables and Connectors
Use a microphone with an XLR connector to
connect the microphone to the Mbox Mini.
The Mbox Mini can only supply power through
a microphone cable with an XLR connector. If
you are not sure about the phantom power re-
quirements for your microphone, refer to your
microphone’s documentation or contact the
manufacturer.
Phantom Power
Some microphones require power to operate.
This power, called phantom power, is supplied ei-
ther by a battery in the microphone, or through
an audio interface (such as Mbox Mini) that can
supply power through the microphone cable.
Most condenser microphones (such as an
M-Audio Solaris) require phantom power to op-
erate. Dynamic microphones (such as a Shure
SM57 or M-Audio Aries) do not require phan-
tom power to operate, but are not harmed by it.
Using a Mic that Has an XLR
Connector
To use a microphone that has an XLR connector:
1 Plug your microphone cable into the Mic/Line
input on the back of Mbox Mini.
2 Set the Combo/DI switch on the back to
Combo (or “microphone”) position. The button
should be out, not pressed in.
3 If your microphone requires phantom power,
make sure the microphone is connected, then
press the Phantom Power switch (labeled 48V)
on the back of the Mbox Mini. 48V phantom
power is enabled when the switch is pressed in.
4 On the front of the Mbox Mini, turn the Mix
control fully left to Input.
5 On the front of the Mbox Mini, carefully turn
the Input 1 Gain control to the right to increase
the input level of your microphone signal.
6 If the incoming signal is too loud, pull the
Gain knob out to engage the –20 dB pad.
XLR connector
Although phantom power can be used
safely with most microphones, it is possible
to damage some ribbon microphones with
it. Always turn off phantom power and wait
at least ten seconds before connecting a rib-
bon microphone.

Mbox Mini Setup Guide14
Connecting Instruments to
the Mbox Mini
Mbox Mini provides Line/DI inputs that sup-
port direct instruments (such as electric guitar
and electric bass), and line level devices (includ-
ing electronic audio sources such as mixers,
samplers, keyboards, turntables, and synthesiz-
ers).
To use a guitar with Mbox Mini:
1 On the back of the Mbox Mini, plug your gui-
tar cable into one of the DI inputs (in this exam-
ple, input 2).
2 On the back panel, make sure the Line/DI
switch is in the “in” position.
3 On the front of the Mbox Mini, turn the Mix
control fully left to Input.
4 On the front of the Mbox Mini, carefully turn
the input’s Gain control to the right to increase
the input level of your guitar.
5 If the incoming signal is too loud, pull the
Gain knob out to engage the –20 dB pad.
To use a keyboard or mixer with Mbox Mini:
1 Plug your keyboard, mixer, or other audio
source into either the Input 1 or Input 2 (TRS)
inputs on your Mbox Mini. If your source is ste-
reo (such as a stereo keyboard or the stereo out-
put from a mixer), connect the left channel
(often the white plug) to Input 1, and right
channel (often the red plug) to Input 2.
2 If you are using Input 1 (Mic/Line), set the
Combo/DI switch on the back panel to Combo,
by pressing the switch out.
3 On the front of the Mbox Mini, turn the Mix
control fully left to Input.
4 Set your instrument’s volume to its optimal
level. For example, the optimal level for most
keyboards is between 80% and 100% of maxi-
mum volume.
5 On the front of the Mbox Mini, carefully turn
the input’s Gain control to the right to increase
the input level of your keyboard.
6 If the incoming signal is too loud, pull the
Gain knob out to engage the –20 dB pad.
If using Input 2 or if using both inputs
(1 and 2) in a stereo configuration, make sure
the Line/DI button for Input 2 is in the “out”
(Line) position.

:15
chapter 5
Using the Driver Control Panel
The Mbox Mini Driver Control Panel lets you
configure settings for your audio interface for
use with Pro Tools or other audio applications
that support the CoreAudio Drivers (Mac) or
ASIO Audio Drivers (Windows) standard.
The Driver Control Panel also features conve-
nient links to driver updates, downloadable
manuals, FAQs, tech support, product registra-
tion, and our website (www.avid.com).
To open the Driver Control Panel:
On Mac, launch System Preferences (Apple
menu > System Preferences), then double-click
Avid Mbox Mini. (You can also open the Driver
Control Panel from the Applications menu.)
– or –
On Windows, choose Start > All Programs >
Avid > Mbox Mini > Mbox Mini Control Panel.
To open the Driver Control Panel from Pro Tools:
1 Choose Setup > Hardware in the Edit window.
2 Click launch control panel.
Mbox Mini Driver Control Panel in stand alone mode
Web links
Sample Rate menu
Status indicators
Buffer Size menu

Mbox Mini User Guide16
Setting Sample Rate and
Buffer Size
From the Driver Control Panel, you can change
the Sample Rate or Buffer Size setting or access
the Hardware Setup dialog for your Mbox Mini
or third-party application.
To set the Sample Rate:
Click the Sample Rate pop-up menu (located
in the upper part of the Driver Control Panel)
and choose the Sample Rate you want.
Sample Rate
You may select from the following sample rates:
• 44100
• 48000
To set the Buffer Size:
Click the Buffer Size pop-up menu and choose
the number of samples you want.
Buffer Size (Windows Only)
You may select from the following number of
samples:
• 128 samples
• 256 samples
• 512 samples
• 1024 samples
• 2048 samples
• 4096 samples
Using the Status Indicators
Along the bottom-left of the Driver Control
Panel are the following status indicators:
Hardware Connected
This indicates if a properly installed, powered-
on Mbox Mini is connected to the computer.
Streaming
This indicates if audio from a Digital Audio
Workstation or a media player (such as iTunes or
foobar) is currently streaming within Pro Tools.
Viewing Firmware and
Installer Information
Directly above the status indicators, you can
view the firmware version of the Mbox Mini
hardware, and the package version of the
Mbox Mini driver installer.
Accessing the Web Links
Along the bottom-right of the Driver Control
Panel you can easily access helpful online re-
sources on our Avid website (www.avid.com) by
clicking on the following pop-up menus:
•Manual
•Updates
• Support
•FAQs
•Register
Clicking on any of the “Web links” will
open your web browser. Your computer must
have Internet access for these pages to load.