AVOURY ONE User manual

.58

EN
TABLE OF CONTENTS
PAGE 23
Table of Contents ................................................................................................................................23
Device overview ...................................................................................................................................24
General information.............................................................................................................................26
Reading and storing the user manual................................................................................................................... 26
Explanation of symbols............................................................................................................................................26
Safety....................................................................................................................................................27
Proper use................................................................................................................................................................... 27
Safety instructions.................................................................................................................................................... 27
Start-up ................................................................................................................................................30
Checking the tea machine and package contents............................................................................................30
Use ........................................................................................................................................................ 31
Switching on the tea machine.................................................................................................................................31
Rinsing the brewing chamber..................................................................................................................................31
Making tea .................................................................................................................................................................. 32
Cancelling the tea preparation process............................................................................................................... 32
Switching o the tea machine................................................................................................................................ 33
Adding extra water.................................................................................................................................................... 33
Emptying the capsule container............................................................................................................................ 33
Emptying the drip drawer........................................................................................................................................ 33
Setting the water hardness..................................................................................................................................... 34
Using a water lter.................................................................................................................................................... 34
Setting the water lter ............................................................................................................................................. 34
Cleaning and Descaling.......................................................................................................................35
Activate care mode................................................................................................................................................... 35
Cleaning....................................................................................................................................................................... 35
Descaling..................................................................................................................................................................... 37
Control via Avoury App ........................................................................................................................38
Troubleshooting...................................................................................................................................39
Technical data ......................................................................................................................................41
Disposal................................................................................................................................................41
6000746 | EN | 09/22

EN
DEVICE OVERVIEW
PAGE 24
Filling level display (oat gauge)
Drip tray
Drip drawer with capsule container
and drip tray
Outlet
5
6
7
8
1
8
7
5
6
4
2
3
Control panel
Capsule compartment
Water lter
Water tank
1
2
3
4
Part name

EN
DEVICE OVERVIEW
CONTROL PANEL
PAGE 25
Start-Button
LED “Empty water tank”
LED “Empty capsule container”
LED “Carry out cleaning”
LED “Carry out descaling”
Button brewing time +
9
10
11
12
13
14
Button brewing time –
Display brewing time
Display lling capacity
Button filling capacity +
Button lling capacity –
15
16
17
18
19
9
12
10
11
14
18
13
16
17
15
19
Part name

EN
GENERAL INFORMATION
General
information
Reading and storing the
user manual
This user manual relates to the Melitta
Avoury One tea machine (hereinafter simply
referred to as the “tea machine”). It contains
important information on start-up and opera-
tion. Read the user manual carefully, especially
the safety instructions, before using the tea
machine. Failure to comply with the instructions
provided in this user manual may result in severe
injuries or in damage to the tea machine. The
user manual is based on the standards and reg-
ulations in force in the European Union. When
abroad, you must also observe country-specific
guidelines and laws. Store the user manual for
future use. If you pass on the tea machine to
a third party, you must also pass on this user
manual.
Explanation of symbols
The following symbols and signal words are used
in this user manual, on the tea machine or on the
packaging.
WARNING!
This signal symbol/word designates a hazard
with a moderate degree of risk which may lead
to death or severe injury if not avoided.
CAUTION!
This signal symbol/word designates a hazard
with a low degree of risk that, if not avoided, may
result in minor or moderate injury.
NOTICE!
This signal word warns against potential damages
to property.
This symbol provides you with
useful information about using the
device.
Declaration of conformity:
Products marked with this symbol
meet all the applicable Commu-
nity regulations for the European
Economic Area.
PAGE 26

EN
PAGE 27
SAFETY
Safety
Proper use
The tea machine is intended solely for preparing
hot tea with specially developed Avoury
capsules. It is intended for private use only and
is not suitable for commercial purposes. Use
the tea machine only as described in this user
manual. Any other use is deemed improper and
may result in damage to property or even injury.
The tea machine is not a child’s toy. The manu-
facturer accepts no liability for damage caused
by improper or incorrect use.
Safety instructions
WARNING!
Risk of electric shock!
A faulty electrical installation or
excessive mains voltage may result in
an electric shock.
• Connect the tea machine only if the
mains voltage of the socket corre-
sponds to the specification on the
rating plate.
• Connect the tea machine only to a
properly installed mains socket.
• Connect the tea machine only to an
easily accessible mains socket to al-
low you to quickly disconnect the tea
machine from the mains supply in the
event of a fault.
• Do not operate the tea machine if it
has any visible damage or if the mains
cable and/or mains plug is defective.
• If the mains cord of the tea machine is
damaged, it must be replaced by the
manufacturer, its After Sales Support
department or a similarly qualified
person to prevent risks.
• Do not open the housing yourself, but
leave the repairs to a qualified profes-
sional. Contact a specialist workshop

EN
SAFETY
PAGE 28
for this. Liability and warranty claims
are waived in the event of repairs per-
formed by the user, improper connec-
tion or incorrect operation.
• Only parts that comply with the
original device data may be used for
repairs. This tea machine contains
electrical and mechanical parts which
are essential for providing protection
against sources of danger.
• The tea machine may not be operated
with an external timer or a separate
telecontrol system.
• Do not use adapters, multiple sockets
or extension cables to connect the
tea machine. In the event these are
required, use only equipment that has
been tested and that corresponds
with the safety regulations and the
device data.
• Do not modify the tea machine in any
way.
• Do not immerse the tea machine,
the mains cable or the mains plug in
water or other liquids.
• Never touch the mains plug with wet
hands.
• Never pull the mains plug out of the
socket by the mains cable; instead,
always pull on the plug itself.
• Never use the mains cable as a carry-
ing handle.
• Keep the tea machine, mains plug
and mains cable away from open
flames and hot surfaces.
• Lay the mains cable so that it does not
pose a tripping hazard.
• Ensure there are no kinks in the
mains cable and do not lay it over
sharp edges.
• Use the tea machine indoors only.
• Never use the tea machine in damp
spaces or in the rain. Never store the
tea machine in such a way that it could
fall into a bathtub or sink.
• Never reach to retrieve an electrical
device that has fallen into water. In
such a case, immediately disconnect
the mains plug from the socket.
• Do not insert anything other than
Avoury capsules into the tea machine.
• Make sure that children do not insert
any objects into the tea machine.
• When cleaning, including cleaning the
outside of the tea machine, or if there
is a fault, always switch the tea ma-
chine off and pull the mains plug out
of the socket.

EN
SAFETY
PAGE 29
WARNING!
Danger for children and persons with
impaired physical, sensory or mental
capacities (e.g. older persons with
reduced physical and mental capaci-
ties) or lack of experience and know-
ledge (e.g. older children).
• This tea machine may be used by
children above the age of eight and
by persons with reduced physical,
sensory or mental abilities or by those
without experience and/or know-
ledge, only if they are supervised
or have been instructed in the safe
use of the tea machine and have an
understanding of the dangers that
are associated with using it. Children
may not play with the tea machine.
Cleaning and user maintenance must
not be performed by unsupervised
children.
• Keep children under eight years of age
away from the tea machine and the
connection cable.
• Never leave the tea machine unat-
tended during operation.
• Do not allow children to play with the
packaging material and small parts.
Children may get caught in the pack-
aging when playing or swallow small
parts and choke.
CAUTION!
Scalding hazard!
The tea machine releases hot water
during use. Parts of the tea machine
become hot and can cause scalding.
• Hot water is released from the outlet.
Keep all parts of the body away from
the outlet during the brewing pro-
cess.
• Do not touch the hot parts of the tea
machine at the outlet during opera-
tion. Ensure you remain a sufficient
distance away from the tea machine.
Clearly advise other users of the risks.
NOTICE!
Risk of damage!
Improper use of the tea machine may
damage the tea machine.
• Place the tea machine on an easily
accessible, level, dry, heat-resistant
and sufficiently stable work surface.
Do not place the tea machine on the
edge or lip of the work surface.

EN
SAFETY + STARTUP
PAGE 30
• Never place the tea machine on or
close to hot surfaces (e.g. hobs, etc.).
• Ensure that the mains cable does not
come into contact with hot compo-
nents.
• Never expose the tea machine to
high temperatures (heaters, etc.) or to
effects of the weather (rain, sun, etc.).
Never store the tea machine in a loca-
tion where the ambient temperature
falls below 0 °C.
• Never pour liquids into the tea machine,
except into the water tank.
• Only pour fresh, cold tap water into the
water tank.
• Never pour mineral water, milk or other
liquids into the water tank. The excep-
tion to this is the Avoury liquid descaling
agent for the descaling programme.
• Never use the tea machine when the
water tank is empty.
• Do not overfill the water tank. Fill the
water tank with water up to a maximum
level of two finger widths below the
upper edge.
• Do not continue to use the tea machine
if the plastic components of the tea
machine have any cracks or flaws or
have become warped. Replace
damaged parts only with corresponding
original spare parts.
Start-up
Checking the tea machine
and package contents
NOTICE!
Risk of damage!
Carelessness in opening the packaging
with a sharp knife or other pointed
objects may quickly damage the tea
machine.
• Open it very carefully.
1. Remove the tea machine from the
packaging.
2. Check to make sure that all of the
contents have been provided (see
chapter „Device overview“).
3. Check whether the tea machine or
the individual parts are damaged. If
this is the case, do not use the tea
machine. Contact the manufacturer
at the specified service address (via
Avoury.com or phone [phone]
6000).

EN
PAGE 31
USE
Use
Avoury tea capsules contain ideal portions of tea
for use in the tea machine.
The size of the capsule is determined by the fact
that the tea needs space to develop during the
brewing process. A lid foil ensures that the tea
in the capsule is protected against loss of its
aroma. This lid foil must be removed before
the capsule can be used. There is a porous net
under the lid foil, which has either fine mesh or
coarse mesh depending on the fineness of the
loose tea. Each capsule has a code that tells the
tea machine which parameters the tea requires
to provide maximum enjoyment.
Download the free Avoury App directly
to update the machine software (see
chapter „Control via Avoury App“).
Switching on the tea
machine
1. Connect the mains plug with a properly
installed socket.
2. Ensure that the capsule compartment 2
is closed.
3. To switch on the tea machine, press the
Start-Button . The Start-Button
flashes whilst it is starting up. Once the tea
machine is ready, the Start-Button will
show a continuous light.
Rinsing the brewing
chamber
The tea machine must be cleaned out before the
first use and after longer periods of non-use to
remove any manufacturing residues and con-
tamination. To do this, the tea machine must be
switched on.
1. Remove the packaging material and the ad-
hesive strips as well as the sticker with the
serial number on the drip tray 6.
2. Remove the water tank 4and rinse it out
with fresh tap water.
3. Replace the water tank 4again.
4. Fill the water tank with water up to a maxi-
mum level of two finger widths below the
upper edge.
5. Place a collecting vessel that holds at least
300 ml volume under the outlet 8.
6. Push the Start-Button and wait until the
machine is ready-to-use.
7. Press the – /+ filling capacity buttons
at the same time.
The tea machine rinses the brewing cham-
ber and dispenses water into the collecting
vessel. The machine is fully rinsed when the
Start-Button shows a continuous light.
8. Empty the contents of the tray of the drip
drawer 7and the collecting vessel into the
sink.

EN
USE
PAGE 32
Making tea
1. Remove the water tank 4and fill it with
water up to a maximum level of two finger
widths under the upper edge of the water
tank.
2. Switch on the tea machine.
3. Wait until the Start-Button shows a
continuous light.
4. Place a collecting vessel under the outlet 8.
The collecting vessel must be able to hold at
least 250 ml.
5. Remove the lid foil from the capsule.
6. Open the capsule compartment 2and
insert the capsule the right way up. The ap
on the capsule must be pointing upwards
(see illustration).
7. Close the capsule compartment 2again.
The tea machine will automatically read the
preparation parameters provided by the
caspule.
8. If nescessary, use the – /+ buttons for
filling capacity to set the desired quantity of
water. Select a lower quantity of water for
stronger tea and a higher quantity of water for
weaker tea. Each press increases or decrea-
ses the water quantity by 15 ml (max. 210 ml,
min. 150 ml). The standard cup size is 180 ml.
9. If necessary, use the – /+ brewing time
buttons to set the desired brewing time for
the tea. Select a longer brewing time for
stronger tea and a shorter brewing time for
weaker tea. The brewing time will increase or
decrease by one minute with each press.
10. Press the Start-Button to brew the tea.
The brewing time display 16 shows the
remaining time until the tea is completely
brewed. The LEDs on the filling capacity
display 17 will switch off one after another
until the tea has been dispensed in full.
After the brewing process, the capsule will
be ejected automatically and the brewing
container will be rinsed to prevent any aroma
mixing and to ensure that you can enjoy
the flavours of each type of tea. The rinsing
water runs into the drip tray and not into the
cup.
11. To prepare another cup, open the capsule
compartment 2, remove the lid foil and
insert a new capsule.
Cancelling the tea
preparation process
• Press and hold the Start-Button for ap-
prox. 3 seconds during the brewing process.
The liquid contained in the brewing container
at the time when the process is stopped is
released into the cup situated beneath the
outlet 8.

EN
PAGE 33
USE
Switching off the tea
machine
• Press and hold the Start-Button for
approx. 3 seconds. The tea machine switches
into standby mode. After 10 minutes, the tea
machine automatically switches into standby
mode if you do not press any buttons.
Adding extra water
If there is not enough water in the water tank
4to complete another brewing process,
the LED „Empty water tank“ will show a
continuous light. You cannot carry out any
more brewing processes until you have refilled
the water tank.
1. Remove the water tank 4and fill it with
water up to a maximum level of two finger
widths below the upper edge of the water
tank.
2. Replace the water tank 4again.
The LED „Empty water tank“ will go out.
If the water level is too low, you should
add fresh water before the LED „Empty
water tank“ shows a continuous
light.
Emptying the capsule
container
After five brewing processes, the LED “Empty
capsule container” will show a continuous
light and the capsule container must be emptied.
Otherwise, no further brewing processes can be
carried out.
1. Remove the drip drawer 7from the tea
machine and take out the capsule container.
2. Dispose the used capsules in the yellow re-
cycling bin or use the Avoury recycling bag.
3. Place the capsule container and the drip
drawer back into the tea machine. The LED
„Empty capsule container“ will go out and
the tea machine is ready-to-use again.
Emptying the drip drawer
1. Remove the drip drawer 7from the tea
machine and empty the capsule container.
2. Remove the metal cover of the drip tray 6.
3. Empty the drip drawer.
4. Then replace all the parts in the tea machine.

EN
USE
PAGE 34
The contents of the following pages
refer to the machine software from
version 1.3.58. To perform the system
update, download the free Avoury App
(see chapter „Control via Avoury App“).
Setting the water hardness
1. Switch on the tea machine.
2. Press the buttons for setting the brewing
time – /+ simultaneously. The display
16 on the tea machine shows the level of
water hardness currently set.
3. To set the water hardness level, press the
– /+ buttons for the brewing time.
If the LEDs on the left of the display show
a continuous light, it is set for hard water. If
the LEDs on the right of the display show a
continuous light, it is set for soft water.
SOFT
MEDIUM
HARD
WEICH
MITTEL
HART
4. Conrm the settings by pressing the Start-
Button .
Using a water filter
You can insert a water filter into the water tank
4. This filters limescale and particles out
of the water. This improves the enjoyment of
the tea and extends the service life of the tea
machine.
1. Fill the water tank 4halfway with fresh tap
water.
2. Place the water filter with one of the two flat
sides into the tea machine pointing towards
the valve in the water tank 4so that the
water filter sits tightly parallel to the bottom.
3. Now fill the water tank 4completely with
fresh tap water.
4. The water filter must be changed every two
months to prevent excessive contamination
from microorganisms.
The water lter must be removed before
carrying out the descaling programme.
Remember to set the water hardness
to water lter! (see chapter „Setting the
water lter“). If you are not going to use
the tea machine for a longer period of
time, please make sure that the water
lter is placed in a full water tank.
Setting the water filter
1. Switch on the tea machine.
2. Press the buttons fot setting the brewing
time – /+ simutaneously. The display
17 on the tea machine shows the usage of
the water filter currently set.
3. To set the water filter, press the buttons for
filling capacity + . If all LEDs show a
continuous light, you are using a water filter.
If all LEDs are extinguished, you are not
using a water filter.
water lter
no water lter
4. Confirm the setting by pressing the Start-But-
ton .

EN
PAGE 35
CLEANING AND DESCALING
Cleaning and
Descaling
The cleaning and descaling program-
me must be completed once started.
Stopping this process prior to comple-
tion, e.g. as a result of an interruption
in the power supply, causes the pro-
gramme to restart or may lead to error
notications in exceptional cases (all
four info LEDs 10 , 11 , 12 & 13 are
ashing).
Before putting in a capsule for cleaning
or descaling, the care mode must be
activated. If care mode is deactivated
the capsule will be ejected.
Activate care mode
1. Switch on the tea machine.
2. Activate the care mode by pressing the lling
capacity
– and brewing time button +
simultaneously for approx. 3 seconds. When
the rst LED at
– and the last LED
at + show a continuous light the care
mode is activated.
3. To deactivate the care mode, if necessary,
press and hold the lling capacity
– and
brewing time button + again simultaneous-
ly for approx. 3 seconds.
Important: Care mode is deactivated when:
•the Avoury One tea machine is turned o /
turns o automatically
•the cleaning/ descaling programme is
nished.
Cleaning
When the LED “Carry out cleaning” shows a
continuous light, the appliance should be clea-
ned using a cleaning capsule. The programme
takes approximately 25 minutes.
1. Switch on the tea machine and wait until the
Start-Button shows a continuous light.
2. Fill up the water tank 4completely with
fresh tap water and then insert the water
tank again.
3. Activate the care mode.
4. Open the capsule compartment 2, remove
the lid foil from the cleaning capsule and
insert a cleaning capsule. Then close the
capsule compartment 2.
5. The LED “Carry out cleaning” starts to
flash red and the Start-Button shows a
continuous light.
The LED “Carry out cleaning” flashes
red throughout the whole cleaning
programme and goes off when the
programme is finished.
6. To start the cleaning programme, press the
Start-Button .
7. When the LED “Empty capsule container”
shows a continuous red light, remove the
drip drawer 7and empty the drip tray and
the capsule container (Removal must also be
performed if the capsule drawer is empty. If
the LED remains lit after removal, wipe the
inner housing dry so that the sensors are not
prevented by the moisture).

EN
CLEANING AND DESCALING
PAGE 36
8. Insert the drip drawer 7again and place
a vessel with a volume of at least 300 ml
below the outlet 8.
9. The LED “Empty capsule container” goes
off and cleaning starts automatically.
Cleaning is carried out in two cycles. The LEDs
in the “Brewing time” display 16 go o one
after the other during cleaning and indicate
the time in which the cleaning agent dissolves
and takes eect. When the LEDs are all o, the
cleaning uid is discharged into the collecting
vessel.
First cycle
10. The first cycle is finished when the Start-
Button shows a continuous light.
11. Empty the collecting vessel and put it back
under the outlet 8.
Second cycle
12. Press the Start-Button to start the second
cycle.
13. The second cycle is nished when the LED
“Empty capsule container” shows a
continuous red light and the Start-Button
ashes.
14. Empty the collecting vessel. Remove the
drip drawer 7with the drip tray and the
capsule container to remove any liquids.
Then put everything back in place and place
the drip tray back under the outlet 8.
15. The LED “Empty capsule container“ goes
o and rinsing begins automatically.
The rinsing process rinses the brewing
chamber with fresh water at the end of the
process. The liquid that has run through is
discharged into the collecting vessel. At the
end of the rinsing process the cleaning cap-
sule is ejected.
16. Rinsing is nished when the LED “Empty
capsule container” shows a continuous
red light and the Start-Button ashes.
17. Empty the collecting vessel. Remove the
drip drawer 7with the drip tray and the
capsule container to remove any liquids.
Then put everything back in place.
18. The LEDs “Empty capsule container”
and “Carry out cleaning” go o and the
Start-Button shows a continuous light. If
necessary, rell the water tank 4.
The cleaning program is nished.
Irrespective of how often the Avoury
One tea machine is used, we recom-
mend cleaning it at least once a month
with a cleaning capsule, even if the
LED “Carry out cleaning” does not
show a continuous light. To clean the
machine, activate the care mode and
place a cleaning capsule in the capsule
compartment 2to be able to start the
cleaning programme.

EN
PAGE 37
CLEANING AND DESCALING
Descaling
When the LED “Carry out descaling” shows
a continuous light the descaling programme
should be started. The programme takes approx.
15 minutes.
Important: Remove the water lter before
descaling!
1. Switch on the tea machine and wait until the
Start- Button shows a continuous light.
2. Activate the care mode.
3. Open the capsule compartment 2and
insert an empty descaling capsule (no lid foil
needs to be removed). Then close the capsu-
le compartment 2.
4. The LED “Carry out descaling” starts to
ash red and the Start-Button shows a
continuous light.
The LED “Carry out descaling” flashes
red throughout the whole descaling
programme and goes off when the
programme is finished.
5. To start the descaling programme, press the
Start-Button .
6. The LEDs “Empty water tank” and “Empty
capsule container” show a continuous
red light.
7. Empty the water tank 4. If you use a water
lter, please remove it.
8. Fill the water tank 4with the entire con-
tents of the Avoury liquid descaler (250 ml)
and an additional 250 ml of fresh tap water.
9. Reinsert the water tank 4.
10. The LED “Empty water tank” goes o.
11. Remove the drip drawer 7to empty the
drip tray and the capsule container.
12. Put everything back in place and place a
heat-resistant collecting vessel with a
capacity of at least 300 ml under the outlet
8.
Caution: The liquid is very hot!
13. The LED “Empty capsule container” goes
o and descaling begins automatically.
Descaling is carried out in two cycles. The
descaling liquid that has run through the
machine ows into the collecting vessel.
First cycle
14. The rst cycle is nished when the Start-
Button shows a continuous light.
15. Empty the collecting vessel then put it back
under the outlet 8.
Second cycle
16. Press the Start-Button to start the second
descaling cycle.
17. The second cycle is nished when the LEDs
“Empty water tank” and “Empty capsule
container” show a continuous light and
the Start-Button ashes.
18. Remove the water tank 4and pour out any
remaining liquid.
19. Rinse the water tank 4with fresh tap
water.
20. If required, put the water lter back into the
water tank 4.
21. Fill the water tank 4completely with
fresh tap water and put it back in place. The
LED “Empty water tank” goes o.

EN
CLEANING AND DESCALING + CONTROL VIA AVOURY APP
PAGE 38
22. Empty the collecting vessel. Remove the
drip drawer 7with the drip tray and the
capsule container to remove any liquids.
23. Then put everything back in place and place
the collection vessel under the outlet 8
again.
24. The LED “Empty capsule container” goes
o and rinsing begins automatically.
Rinsing is also carried out in two cycles. The
liquid that has run through the machine ows
into the collecting vessel. When rinsing is
nished the descaling capsule is ejected.
25. The rst cycle is nished when the Start-
Button shows a continuous light.
26. Empty the collecting vessel and put it back
under the outlet 8.
27. Then press the Start-Button to start the
second cycle.
28. When the second cycle is nished the cap-
sule is ejected automatically. The LED “Carry
out descaling” goes o and the Start-
Button shows a continuous light.
The descaling programme is nished.
Control via
Avoury App
The Avoury One tea machine can be controlled
via the control panel, as well as via your smart-
phone. To do this, download the free Avoury App
and register your Avoury One tea machine. In
the Avoury App, you can adjust the brewing time
and cup size individually. Once the tea is brewed,
a notication appears on your smartphone.
Furthermore, you can order new tea, view your
account details and read the online magazine on
the Avoury App. You can also use the interactive
cleaning and descaling mode and download the
latest machine software.
1. Download the Avoury App to your smart-
phone. Scan the QR code to access the
download directly:
Apple App
Store
Google
Playstore
2. Switch on the tea machine and wait until the
Start-Button shows a continuous light.
3. Activate Bluetooth on your smartphone and
connect to your machine via the Avoury App.
4. When the Start-Button ashes, conrm
the connection by pressing the
Start-Button .
5. When the Start-Button shows a
continuous light, the machine is
ready-to-use.

EN
TROUBLESHOOTING
PAGE 39
Troubleshooting
Problem Possible cause Solution
The Start-Button ashes perman-
ently and the tea machine does not
start up.
The capsule compartment 2is
open when switching on/starting up.
Close the capsule compartment 2.
All 4 LEDs 10 , 11 , 12 & 13 ash
at the same time.
System error
(for further information regarding
system errors and related error codes
see page 40)
Press and hold the Start-Button
for approx. 3 seconds until the red
LEDs 10 , 11 , 12 & 13 stop
ashing. The Start-Button ashes
and the tea machine restarts.
The LED “Carry out cleaning”
does not go out.
The cleaning programme was cancel-
led/was not completed.
Restart the cleaning programme and
allow it to be completed.
The LED “Carry out descaling”
does not go out.
The descaling programme was can-
celled/was not completed.
Restart the descaling programme
and allow it to be completed.
Only water (and no tea) is dispensed
from the tea machine.
The lid foil has not been removed
from the capsule.
Remove the lid foil and reinsert the
capsule.
In the event that the lid foil was not removed, the capsule has already been in-
serted into the machine and this has been noticed before the brewing process
has started.
Press and hold the Start-Button
for approx. 3 seconds or open the
capsule compartment 2. The cap-
sule will be ejected without brewing
(as long as the brewing process has
not yet started).
The tea machine ejects the capsules
directly after being inserted. Tea
dispensing is not possible.
The cleaning or descaling program-
me was cancelled/was not comple-
ted.
Check to see whether both LEDs for
“Carry out cleaning” or “Carry out
descaling” show a continuous
light. Then restart the corresponding
programme. Alternatively - rinse the
brewing chamber (see page 31).

EN
TROUBLESHOOTING
PAGE 40
If the 4 LEDs “Empty water tank” , “Empty capsule container” , “Carry out cleaning” and “Carry
out descaling” all ash at the same time this indicates a system error. This may have a number of dif-
ferent causes, some of which you can solve yourself. The error code indicates the cause of the error. This
code is shown in the “brewing time” 16 display. Each LED that shows a continuous white light stands
for “0”. Each LED that ashes stands for “1”. The display should be read from left to right.
Example: black = ashing | white = shows a continuous light
“00010010”
To nd out the cause of the error and possible ways of solving the problem yourself, call our customer
service number 00800 7000 6000 or see the website www.Avoury.com
If a problem exists with the tea machine that is not listed above, or cannot otherwise be rectied with the
solution described, please contact our After Sales Support without delay by visiting www.Avoury.com
or by calling 00800 7000 6000.
Error Codes