AVstumpfl DECOFRAME User manual

29KS
DECOFRAME
MANUAL

AV Stump GmbH | Mitterweg 46 | 4702 Wallern
AVstump@AVstump.com | www.AVstump.com | [phone]
INDEX
GENERAL 3
STANDARDS, REGULATIONS
AND TECHNICAL SPECIFICATION 3
SAFETY 3-4
OPERATION, MAINTENANCE and SERVICE 6
WARRANTY 7
FRAME SET UP 8
MOUNTING 9
CENTRE SUPPORT AND HORIZONTAL STRUT 10

3
AV Stump GmbH | Mitterweg 46 | 4702 Wallern
AVstump@AVstump.com | www.AVstump.com | [phone]
GENERAL
STANDARDS, REGULATIONS and TECHNICAL
SPECIFICATION
This projection screen is in accordance with the safety regulations in DIN standard 19045 and
DIN 56950. The screen fabric is comply with DIN 4102 part 1 and the specications of the according
data sheet. For the technical details and projection-specic material parameters please refer to the
corresponding product data sheet: www.AVstump.com/projectionmaterials
Detailed data of frame components and projection surface can be found on the type labels on each
component and on the labeled soft bags, roller bags or ight cases.
SAFETY
GENERAL INFORMATION FOR THE MANUAL AND SAFETY
This operating manual forms part of the projection screen system and enables a safe and ecient
operation. The safety section provides information about important safety aspects for the protection
of persons, frame and projection materials. Task-related warnings/notes are also contained in the
individual chapters. Read instructions through completely before proceeding and keep for future
reference. You can nd manuals electronically on our website: www.AVstump.com/downloads
PACKAGING MATERIAL
WARNING
Danger of suocation!
• Keep packaging material and foils away from children.
• Do not let children play with packaging material.
Unpack without cutter or any other sharp tool to avoid damaging of
the projection screen. Remove packaging materials by hand. Unpack
projection surface after assembling of the frame.

4
SET UP-ASSEMBLY
MECHANICAL HAZARDS


Projection surface damage in case of faulty assembly or set up.
Make sure all frame parts assembled correctly and all hinges and joints are locked before one unfold and
attach the projection surface.
Please be careful
not to pinch
your ngers!
FALLING OVER
WARNING
Falling over of a projection screen can cause severe injury or death!
FRAME COMPONENTS
Plug-in connections can lead to injury to the hands (body parts).
Please be careful not to pinch your ngers!
Danger of injury due to improper assembly.
Make sure all frame parts assembled correctly and all hinges
and joints are locked before raising screen to standing
position. Falling parts can cause severe injury or death!

5
WARNING
DECOFRAME systems are developed for indoor use only.
Failure to follow warning may result in personal injury due to unforeseen acts of nature.
Any damage and consequential damage caused by outdoor use is not covered by warranty.
BASIC SAFETY REQUIREMENTS
Basic safety requirements for „ying“ projection screens and wall- or ceiling mounting!
If persons are able to stand under the loads, fastening points and slings must not be loaded more than
half the value of the load bearing capacity stated by the manufacturer.
When planning the event or production, not only dead loads but also dynamic forces, potential
breakdown loads and additional loads during operation, as well as during assembly and dismantling
must be taken into account.
Observe the local safety regulations!
FLYING SCREEN
If a modular projection screen is used as a “ying” (free hanging) screen, then all plug-in and clamp
connections must be secured against becoming loose and falling.
It is not allowed to use the projection surface holding the frame parts in position!
Falling parts can cause severe injury or death!
Please make sure that all components are secured safely before raising screen to standing position and
lifting. Use the necessary number of suspension points according to the overall system weight.
A second/auxiliary safeguarding system is mandatory (e.g. steel rope catch)
Please follow the detailed instruction in the manual.


WALL MOUNTING
Before mounting, make sure that the wall, as well as the xing points meet the safety requirements of
the local standards and the required load can be beared.
Danger of injury
due to improper
disassembly.
Falling parts can
cause severe injury
or death!
Beware of
pinch points.
It is not allowed to use the projection surface holding the frame
parts in position! Falling projection screens or parts can cause
severe injury or death!
Please be careful
not to pinch
your ngers!



6
DISASSEMBLY
For disassembly the same safety instructions apply as for assembly and set up. Bring down a projection
screen with the appropriate number of people to avoid falling over of the screen.


OPERATION, MAINTENANCE and SERVICE
FRAME ELEMENTS and ACCESSORIES:
The frame elements and additional elements are maintenance-free.
PROJECTION SURFACE:
The projection surface is packed into a separate cardboard box to avoid any damage by the frame parts,
bleaching and discoloration.
Additionally, following instructions have to be adhered to:
Do not allow the projection surface to get in contact with sharp objects.
Do not bring printed and coloring objects (instructions, magazines, etc.) in contact with the
projection surface! Do not write on the projection surface!
Colors penetrate the projection surface and cannot be cleaned anymore!
Store the projection surface cleaned and dry at room temperature only!
COLD BREAK
A projection foil must never be stored or transported below 5° C. There is a risk of a cold break! The
lm becomes very brittle and splinters like glass! When transporting the projection surface at low
temperatures do not unroll the surface unless it has reached its full elasticity at room temperature.
Otherwise there is the risk of cold break of the projection screen.
The ideal temperature range for assembling folding screens to prevent damaging the surface is 54°-82° F
(12°-28° C). Assembling below recommended temperatures may damage surface and void warranty
CLEANING OF THE PROJECTION SURFACE
Use a white clean cotton cloth saturated with clear water (optionally mild soap water) and gently
wipe the area in one direction (no circular motion). Wipe dry with another cotton cloth.
To clean a stubborn stain, use methylated spirit and follow the same procedure.
Clean rear projection surfaces in case of imperative only!
Falling parts can cause severe injury or death!

7
WARRANTY
The warranty period for production deciencies is 5 years for the frame elements and 24 months
for the projection surface.
DECOFRAME is developed for indoor use only.
Any damage and consequential damage caused by outdoor use is not covered by warranty.
The general terms and conditions are available at http://avstump.com/agb
LIMITATION OF LIABILITY
All the details in this manual were compiled in consideration of the standards and legal regulations
applicable at this time, as well as the experience of the manufacturer and qualied sta. The
manufacturer accepts no liability for damage to persons or things (projection screen, other devices,
goods, etc.) resulting from:
Non-observance of the manual and the regulations/safety instructions contained therein.
• Failure to comply with the local safety regulations.
• Inappropriate use (misuse).
• Use of unauthorized and non-trained sta.
• Unauthorized equipment conversions and technical modications by the operator himself.
• Use of spare parts not approved by the manufacturer.
• Typesetting and print errors.
Failure to observe the above points will invalidate the warranty claims.
Technical specications are subject to change without notice.
The local regulations and safety regulations and the essential safety requirements apply for the use of
this projection screen.
DISPOSAL
At the end of its lifetime this product must not be disposed of with normal household waste but needs
to be taken to a collection site for recycling.
Separate disposal of the product makes an important contribution towards environmental protection.
Frame components are made of aluminum and steel. The projection material is PVC vinyl.
Contact your local disposal company for the address of a collection center.
Subject to modications, errors expected !

8
1 2
3 4
5 6
FRAME SET UP
Lay out the frame elements according to the
labeling as shown on the picture.
The corners are each connected with one big
and two small angle brackets.
Slide in the angle brackets into the corresponding
slots of the two to be connected frame elements.
Beware of pinch points!
Put the frame elements together without a gap
and x them with the enclosed allen key at the
hexagon socket set screws.
Frame elements and projection surface are
delivered in two seperate cardboard boxes.
Please mind the warnings on the packaging.
In case of more than four frame elements or
center supports and horizontal strut elements
Please follow the instructions under point 13-23.

9
7 8
9 10
11 12
In case of center supports and horizontal struts
we recommend to attach the projection surface
rst and then please follow the instructions
under point 16-23.
Do not open the packaging of the surface before
the assembly of the basic frame is nished to avoid
damages of the surface by the sharp edges of the
frame proles.
Lay out the surface according to the labeling
on the backside of the surface into the frame.
Take care that the ground is absolutely clean!
The surface is attached to the frame at the
circumferential slot with its hooks.Middle
struts or other support elements are mounted
afterwards. See point 16 to 22.
MOUNTING
The Decoframe is mounted to the wall with its
preinstalled keyhole brackets, which can be
adjusted individually.
WARNING
Falling parts!

10
13 14 15
16 17 18
19 20 21
22 23
CENTRE SUPPORT AND HORIZONTAL STRUT
In case of divided proles, linear connectors are used to join them.Slide in the connectors each half the length in
the corresponding slots of the two to be connected frame elements. Put the proles together without a gap and
x them with the enclosed allen key at the hexagon socket set screws.
Beware of pinch points!
Center supports are mounted at the preinstalled connectors. Take o the screws and place the center support
according to the pictures in the Decoframe and secure it with the three philips head countersunk screws.
Horizontal struts are mounted at the preinstalled connectors on the frame side and on the center supports at the
M6 thread inserts with countersunk screws.
As an option with large Decoframes
additional small key-hole plates can
be attached for wall mounting.