Axent ONE E80.0500.0001.9 Configuration guide

CLEANING MAINTENANCE
Article No. E80.0500.0001.9
Article No. E80.0510.0001.9
AXENT.ONE / AXENT.ONEPLUS

youtube |Disassembly / assembly WC seat cover
CERAMICS
Use for daily cleaning of ceramic surfaces with a clean cloth , warm water and a mild liquid detergent. Wipe the surface where possible, dry
with a soft cloth. The use of abrasives, solvents, microfibre cloths and abrasive sponges are not recommended because they can damage
the surface. Use a bathroom cleaner to remove stubborn dirt.
Use a mild soap solution to clean the seat and please take care that the seat and hinges are not left damp. Dry off any residual water or
cleaning agent with a soft close. Avoid contact of the seat and hinges with abrasive, corrosive or chlorine-based cleaners, as these may
cause damage or lead to flash rust.
CLEANING THE SHOWER ROD
Service functions can be carried out via the multi-function rotary knob.
DECALCIFYING SHOWER ROD AND WATER-BEARING PARTS
Prepare a container with 200 ml liquid descaler (preferably Durgol).
Level 2 activation
–Keep the rotary knob pressed (5 sec) until the „ambient light“ flashes slowly.
–Release the knob.
–Press the rotary knob again (5 sec.) until „Ambient light“ flashes quickly.
Extending the shower rod
–Turn the knob clockwise.
If no adjustment is made within 3 minutes, the shower rod is automatically retracted.
The shower rod extends.
–Clean the Inox shower rod with a soft cloth, sponge or brush.
Resetting the shower rod
–Turn the knob clockwise again.
The shower rod returns to its original position.
Activation level 2
–Keep the rotary knob pressed (5 sec) until the „ambient light“ flashes slowly.
–Release the knob.
–Press the rotary knob again (5 sec.) until „Ambient light“ flashes quickly.
Extending the shower rod / emptying the water system
–Pull out the knob and turn it clockwise.
The water system is completely emptied and the shower rod extends without shower function.
–Immerse the shower rod in a container
–Allow the descaling liquid to soak up completely.
The shower rod retracts and the liquid descaler circulates in the wa-
ter-bearing parts. The liquid descaler is automatically ejected.
The entire water system is rinsed 3 times with fresh water.
The night light flashes slowly during the entire process.
This process takes about 3 minutes and cannot be interrupted.
Removing the WC seat/cover unit
–Fold up the seat and cover.
–Pull the seat with cover vertically 90° upwards out of the holder.
Cleaning the WC seat and cover
–Clean the WC seat with a damp cloth.
–Use a soft sponge for stubborn dirt and then wipe dry.
There are electronics in the seat, so do not immerse or rinse in water!
Make sure that the hinges do not remain damp, wipe dry.
Cleaning hinges
1. clean and dry the hinges on the cover with a damp cloth.
2. clean bolts on WC seat with a damp cloth and dry.
Fitting the WC seat/cover unit
1. insert the WC seat with cover vertically from above
The left hinge pin from the seat must first be pushed into the left side of the seat
support.
2. while pushing in the right hinge pin on the seat, let the WC seat slide down
completely.
3. the pressed hinge pin audibly engages in the holder.
CLEANING TOILET SEAT
youtube | Cleaning / Decalcifying
3
2
1
5ײ
5ײ/ 5″
/ 5″
32

REMOTE CONTROL
The AXENT.ONEPlus model has a remote control.
Cleaning the remote control
Wipe the remote control with a slightly moistened, lint-free cloth with a
small amount of detergent.
Charging the battery
Please charge the remote control for at least 24 hours before the first
use.
If less than 15% power remains, the AXENT logo on the remote control
will flash,
–This means that the battery must be charged.
–To do this, connect the original charging cable supplied to the char-
ging connector on the remote control.
–The indicator light shows the battery power.
–If all 5 LEDs light up, the remote control is fully charged.
CI_Z80.1300.0200_AXENT.ONE_EN_2000916
Cleaning interval Cleaning extent
Regularly –Wipe water drops dry with a soft, lint-free cloth
Weekly /
per month
–Remove the toilet seat and lid and clean them separately
–Clean hinges on toilet seat and cover with a moistened cloth
–Thoroughly wipe all surfaces and corners with a damp, lint-free cloth and a mild, liquid cleaning agent
–Check the spray nozzle for signs of scaling
Quaterly –Work out the decalcification program
CLEANING RECOMMENDATION
A current version of this document and additional documents can be downloaded via
www.axentbath.ch
AXENT International AG
[e-mail]
www.axentbath.ch