Axess Spbp4401 User manual

TWIN BLUETOOTH

CONE SPEAKERS

MODEL NO: SPBP4401

Safety information

Important - Please read these instructions fully before

installing or operating

Safety information

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting

General safety information

• Keep the product and all its parts out of reach of small children.

• This product is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning the use of the appliance

by a person responsible for their safety.

• Do not attempt to open the product. This product does not contain any user

serviceable parts. Unauthorised handling of the device may damage it and will void

your warranty.

• Do not use your Wireless Speakers near emergency/intensive care medical

equipment; if you have a pacemaker fitted or during an electrical storm.

• To avoid possible hearing damage, do not listen to these Wireless Speakers at

high volume levels for long periods of time. Always keep the volume within

reasonable limits.

Power source

• Only use the USB charging cables that came with the product. Using unauthorised

charging cables will invalidate your guarantee and may irrecoverably damage the

product..

• Please charge the integral lithium battery in your Wireless Speakers at least once a

month, to prevent damage to and prolong the life of the lithium battery.

Positioning the Wireless Speakers

It is important that you consider carefully in advance where your Wireless Speakers will be

situated and make sure that they are:

• on a flat and stable surface.

• at least 1 metre away from other electrical appliances to avoid interference.

• where they will be in range of the connected or ‘paired’ bluetooth device (e.g. iPod/

iPhone/iPad/Android/other phone/computer, which is about 10 metres or less (33 feet

or less) in line of sight.

Safety information

Important - Please read these instructions fully before

installing or operating

• Within 5 metres of each other, without obstructions between them.

• Never place your Wireless Speakers directly onto antique or polished surfaces.

Moisture and water

• Do not leave your Wireless Speakers in low temperatures as moisture can form inside

the product, which may damage the circuit board.

Ventilation

• Do not block or cover slots, holes or openings on the product by placing on soft

furnishings such as carpets, rugs or beds as these are provided for functionality and/or

ventilation to ensure safe operation of the product.

Heat sources and ﬂames

• Do not leave your Wireless Speakers in high temperatures as electronic devices and

plastic parts may warp in heat.

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting

Getting to know your Wireless Speakers

You’ll be up and running in no time

Ready? Let’s begin...

Please read these instructions carefully. They contain important information which will

help you get the best from your product and ensure safe and correct installation and

operation.

Accessories

The following accessories are included with your Wireless Speakers:

2 x Micro USB Cables.

Fig 1.

Getting to know your Wireless Speakers

You’ll be up and running in no time

Fig 2.

Microphone

LED status indication

3. Power On/Off/Answer/End Call/

Pairing/Play/Pause

4. Aux in socket

5. USB charging socket

Getting to know your Wireless Speakers

You’ll be up and running in no time

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting

Power connection

1. Connect the micro USB end of the charging cables to the USB socket on each

Wireless Speaker (Fig 3). Plug the standard end of each USB charging cable into a

computer or other USB charging device.

2. The small LED status indicator on the front of each Wireless Speaker, behind the

speaker mesh will light up. If the LED is red the Wireless speaker battery is charging,

when the LED changes to blue the battery is fully charged.

Note: Charging the battery before first use, may take up to 3 hours per speaker.

3. When fully charged, unplug the micro USB charging cables.

Note: Your Wireless speakers have an approximate playtime of 8 hours, before they

need to be recharged. When the battery power is low, the LED indicator will flash

quickly and you should plug in and recharge your Wireless Speakers straight away.

Fig 3.

to begin pairing.

’. Select the device name

When found, your Wireless Speakers will be displayed as ‘AAM

Getting to know your Wireless Speakers

You’ll be up and running in no time

Initial set-up

1. Press and hold the Power On button on the top of each Wireless Speaker for about 5

seconds, until ‘Power on, pairing’ is announced, then release the power on buttons.

2. The Wireless Speakers will pair with each other. ‘Pairing successful’ will be announced,

followed by ‘ Left Channel’ and ‘Right channel’ by each speaker, as appropriate.

3. ‘Pairing’ will be announced again as your Wireless Speakers search for a Bluetooth

device to connect to.

Connecting or ‘Pairing’ with your Wireless Speakers

1. On the device that you would like to connect to your Wireless Speakers via Bluetooth

(e.g. iPhone/iPad/Android/other phone/Tablet/Computer), turn on Bluetooth

connectivity and ensure that it is ‘discoverable’.

Note: If necessary, refer to the instructions for your device to add or set up Bluetooth.

2. Select to ‘Add new device’, if necessary.

Note: Some products will automatically search for a new device and so the ‘Add new

device’ option is not available.

4. When pairing is complete the Wireless Speakers will announce ’Pairing successful’,

followed by ‘Second device connected’.

5. Now that you have paired your device with the Wireless Speakers, it will connect to it

when it is within range, which is about 10 metres or less (33 feet or less), line of sight.

6. Your device will remain paired with the Wireless Speakers unless you decide to

disconnect or ‘unpair’ it.

Note: If the pairing process is not completed within 10 minutes, your Wireless Speakers

will automatically power off. Please repeat the power on and pairing steps again to

complete the process.

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting

Using your Wireless Speakers

Let’s get started

Power on

After the initial set up, when you have already paired the Wireless Speakers to each other

and to a separate Bluetooth device, the announcements when you switch on the Wireless

Speakers, will be slightly different.

1. Press and hold the Power On button on the top of each Wireless Speaker for about 5

seconds, until ‘Power on’, is announced, then release the power on buttons.

2. ‘Connected’, followed by ‘Left channel’, Right channel’, then ‘Second device

connected’ will be announced.

Power o

1. Press and hold the Power button on one of the Wireless Speakers for about 3 seconds,

until both speakers announce ‘Power off’.

Bluetooth mode

Check that you have connected or ‘paired’ a product with your Wireless Speakers, please

refer to ‘Connecting or ‘Pairing’ with your Wireless Speakers on page 13.

Listening to Music/Audio using Bluetooth

1. Select and start the music or audio that you wish to listen to on your paired Bluetooth

device, it will now be heard through the Wireless Speakers. Adjust the volume on the

connected device.

2. You can use the controls on your paired Bluetooth device but you can also Play/Pause

the music/audio, on your Wireless Speakers.

Press and release the power button to play/pause.

Note: If there is no audio signal for approximately 10 minutes, your Wireless Speakers

will automatically power off to conserve battery power.

Using your Wireless Speakers

Let’s get started

Using as a Mobile handsfree speakerphone

If you have paired your mobile phone with your Wireless Speakers, the left channel

speaker can be used as a handsfree speaker and will ring when there is an incoming call.

Make an outgoing call:

1. Dial the number as usual on your mobile phone, you will be able to hear the progress

of the call and your caller through the left channel Wireless speaker and your caller will

also be able to hear you.

2. Press and release the Power button on the Wireless speaker or on your mobile phone

to end the call.

Receive an incoming call:

1. Press and release the Power button on your Wireless speaker or answer the call

as usual on your mobile phone. You will be able to hear your caller through your

Wireless Speaker and your caller will also be able to hear you.

2. Press and release the Power button on the Wireless Speaker or on your mobile phone

to end the call.

Aux in mode

Your left channel Wireless Speaker can also be used in Aux in mode.

1. Connect one end of a 3.5mm audio cable (not supplied) to the headphone (or

auxiliary out) socket of your secondary device, connect the other end to the Aux in

socket on the right hand side of your left channel Wireless Speaker. ‘Line in mode’ will

be announced.

2. Press the Play button on your external device to start playback through the Wireless

Speaker.

3. Adjust the volume level on the secondary device.

Note: It is recommended that you unplug the audio cable from the Aux in socket

on the side of the Wireless Speaker, after you have finished listening to your external

device.

AAM

Other information

Helpful technical information

If you require any technical guidance or find that your product is not operating as intended, a simple solution can often be found in the Troubleshooting

Technical speciﬁcation

Audio output: 2 x 3W RMS

Voltage: Input DC 5V 1A

Lithium battery: 500mAh

Bluetooth: Version 4.1

Pairing name:

Profiles HSP, HFP, A2DP, AVRCP

Frequency range: 2.4GHz-2.480GHz

Table of contents