AXIOMTEK CEM700 User manual

4 9418D700000E
© Copyright 2018 Axiomtek Co., Ltd.
Versio A1 December 2018
Pri ted i Taiwa
Quick Start
The basic procedures required to power on CEM700:
(1). Make sure the power is OFF before connecting the CEM700.
(2). Check to ensure the onboard switch SW1-1 and SW1-2 are set to
default (OFF position).
(3). Firmly install DDR4 SO-DIMM in DIMM1/DIMM2 until fully seated. For
single memory channel configuration, install memory module in
channel 0 (DIMM2) DDR4 SO-DIMM socket. For dual memory
channel configuration, install memory modules of the same size, chip
width, density and rank in both channel 0 (DIMM2) and channel 1
(DIMM1) DDR4 SO-DIMM sockets.
(4). Attach heatsink to the CEM700, refer to section Installing Thermal
Solution.
(5). Install the CEM700 onto COM Express
TM
baseboard, for example,
CEB94701 baseboard.
(6). Properly install all necessary peripheral devices such as hard disk,
display, keyboard and etc. to the baseboard.
(7). Firmly attach power supply to the baseboard power connector.
(8). Turn on the system power.
(9). Press power button on the baseboard to start CEM700.
CEM700 Quick Installation Guide
9418D700000E 1
© Copyright 2018 Axiomtek Co., Ltd.
Versio A1 December 2018
Pri ted i Taiwa
Checklist

C
EM
700
Board x1

Product Information
DVD
x1

Q
uick Installation Guide
x1
Note: Please contact your local vendors if any damaged or missing items. DO
NOT apply power to the board if there is any damaged component.
Please refer to the product information DVD for the complete user’s
manual, drivers and utilities. User’s manual and related documents are
in Acrobat PDF format.
Module Layout
Top View
CEM700 COM Express
TM
Type 7 Basic Module

2 9418D700000E
© Copyright 2018 Axiomtek Co., Ltd.
Versio A1 December 2018
Pri ted i Taiwa
Bottom View
Switch Settings
Before applying power to the CEM700, please make sure onboard
switches are in factory default positions.
Switch Description Setting
SW1
Auto Power On
Default: Disable
SW1-1 OFF
Restore BIOS Optimal Defaults
Default: Normal Operation
SW1-2 OFF
Connector
Connector Description
SS1
COM Express
TM
Connector
SS2
COM Ex
press
TM
Connector
DIMM1
Channel
1
DDR
4
SO
-
DIMM
Socket
DIMM2
Channel
0
DDR
4
SO
-
DIMM
Socket
9418D700000E 3
© Copyright 2018 Axiomtek Co., Ltd.
Versio A1 December 2018
Pri ted i Taiwa
Installing Thermal Solution
For thermal dissipation, a thermal solution enables the CEM700’s
components to dissipate heat efficiently. All heat generating components
are thermally conducted to the heatsink in order to avoid hot spots. Below
images illustrate how to install the thermal solution on CEM700.
1. Before installing the heatsink to the CPU module, please apply thermal
grease on the CPU die. Also there is a protective plastic covering on
the thermal pads. This must be removed before the heatsink can be
mounted.
2. Each heatsink is designed for a specific CEM module. The thermal
pads on the heatsink are designed to make contact with the necessary
components on the CEM module. When mounting the heatsink you
must make sure that the thermal pads on the heatsink make complete
contact (no space between thermal pad and component) with the
corresponding components on the CEM module. This is especially
critical for CEM modules that have higher CPU speeds (for example
1.0GHz or more) to ensure that the heatsink acts as a proper thermal
interface for cooling solutions.
3. This CPU module has six assembly holes for installing heatsink plate.
Use screws to secure heatsink plate to the CEM700. Be careful not to
over-tighten the screws.
4. The CPU fan wire should be plugged in the CPU fan socket.