AXIOMTEK CEM700 User manual

CEM700
Intel®Xeon D®and Pentium D®
Processors COM ExpressTM Type 7
Basic Module
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2018 Axiomtek Co., Ltd.
All Rights Reserved
December 2018, Version A1
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please take care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. It discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Intel®is a trademark of Intel Corporation.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 Features...............................................................................................1
1.2 Specifications......................................................................................2
1.3 Utilities Supported ..............................................................................3
Chapter 2 Module and Pin Assignments.................. 5
2.1 Module Dimensions and Fixing Holes...............................................5
2.2 Module Layout.....................................................................................7
2.3 Installing Thermal Solution ................................................................9
2.4 Switch Settings .................................................................................10
2.4.1 Auto Power On and Restore BIOS Optimal Defaults (SW1)..................... 10
2.5 Connector..........................................................................................11
2.5.1 COM ExpressTM Connectors (SS1 and SS2).............................................11
Chapter 3 Hardware Description ........................... 15
3.1 Microprocessor .................................................................................15
3.2 BIOS ...................................................................................................15
3.3 System Memory.................................................................................15
3.4 I/O Port Address Map........................................................................16
3.5 Interrupt Controller (IRQ) Map .........................................................17
3.6 Memory Map ......................................................................................20
Chapter 4 AMI BIOS Setup Utility .......................... 21
4.1 Starting...............................................................................................21
4.2 Navigation Keys ................................................................................21
4.3 Main Menu..........................................................................................23
4.4 Advanced Menu.................................................................................24
4.5 Chipset Menu.....................................................................................35
4.6 Security Menu....................................................................................42
4.7 Boot Menu..........................................................................................43
4.8 Save & Exit Menu ..............................................................................45

v
Appendix A Watchdog Timer and GPIO .................. 47
A.1 About Watchdog Timer.....................................................................47
A.2 About GPIO........................................................................................47
Appendix B BIOS Flash Utility ................................ 49

vi
This page is intentionally left blank.

CEM700 COM ExpressTM Type 7 Basic Module
Introduction 1
Chapter 1
Introduction
The Axiomtek CEM700 is a COM ExpressTM Type 7 Basic Module powered by Intel®Xeon D®
and Pentium D®processors (formerly Broadwell-DE) which compatible to PICMG COM.0
Rev 3.0 specification and support dual cores or multi cores (up to 16 cores).The CEM700 was
designed for customer who need high computing performance and balanced power
consumptions for entry networking, micro servers or various applications.
1.1 Features
Intel®Pentium D®and Xeon D® BGA processors
2 DDR4 SODIMM SO-DIMMs (16GB max/SO-DIMM) support ECC
1 Intel®I210-IT 1000/100/10Mbps supports Wake-on-LAN, PXE Boot ROM, NCSI
2 10Gbe KR interfaces support NCSI
4 USB 3.0 ports
4 USB 2.0 ports
2 SATA-600
Support 32 Lanes of PCI-Express
TPM 2.0

CEM700 COM ExpressTM Type 7 Basic Module
2 Introduction
1.2 Specifications
CPU
Intel®Pentium D®and Xeon D® BGA processors.
Commercial SKUs:
- Pentium®D1508 2.2/2.6GHz 3MB, 25W (2C).
- Xeon®D1527 2.2/2.7GHz 6MB, 35W (4C).
- Xeon®D1577 1.3/2.1GHz 24MB, 45W (16C).
Industry SKUs:
- Pentium®D1519 1.5/2.1GHz 6MB, 25W (4C).
- Xeon®D1539 1.6/2.2GHz 12MB, 35W (8C).
Chipset
NA.
BIOS
American Megatrends Inc. BIOS.
System Memory
Two DDR4 SODIMM SO-DIMMs (16GB max/SO-DIMM) support ECC. Maximum
memory frequency is based on processor number.
TPM
Trusted Platform Module compatible with TPM2.0 Main and PC Client specification
based on Intel®SPI Bus Interface.
Expansion Interface
One PCIe x16 v3.0 (8GT/s) configurable as 1x16, 2x8, 1x8+2x4, 2x4+1x8, 4x4.
One PCIe x8 v3.0 (8GT/s) configurable as 1x8, 2x4.
One PCIe x8 v2.0 (5GT/s); (PCIe lane 7 is supported by build option, in place of
GbE).
USB Interface
Four USB ports comply with USB Spec. Rev. 3.0.
Four USB ports comply with USB Spec. Rev. 2.0.
SATA Interface
Two SATA 6Gb/s ports supported through COM ExpressTM connector.
Graphics
NA.
Ethernet
One Intel®I210-IT 1000/100/10Mbps supports Wake-on-LAN, PXE Boot ROM,
NCSI.
Two 10Gbe KR interfaces support NCSI.
General Purpose Serial Interface
Support two UART TX/RX interfaces with console redirect.

CEM700 COM ExpressTM Type 7 Basic Module
Introduction 3
Other Functions
4 GPO / 4 GPI.
1 I2C.
1 SMBUS.
1 SPI.
1 LPC.
Watchdog Timer: 65536 levels, 65535 secs.
Power
ATX: 12V±5%, 5VSB ±5%; AT: 12V±5%.
Form Factor
Basic module 125mm x 125mm.
1.3 Utilities Supported
Ethernet utility and driver
Chipset driver
USB 3.0 driver
Note
All specifications and images are subject to change without notice.

CEM700 COM ExpressTM Type 7 Basic Module
4 Introduction
This page is intentionally left blank.

CEM700 COM ExpressTM Type 7 Basic Module
Module and Pin Assignments 5
Chapter 2
Module and Pin Assignments
2.1 Module Dimensions and Fixing Holes
Top View

CEM700 COM ExpressTM Type 7 Basic Module
6 Module and Pin Assignments
Bottom View

CEM700 COM ExpressTM Type 7 Basic Module
Module and Pin Assignments 7
2.2 Module Layout
Top View

CEM700 COM ExpressTM Type 7 Basic Module
8 Module and Pin Assignments
Bottom View

CEM700 COM ExpressTM Type 7 Basic Module
Module and Pin Assignments 9
2.3 Installing Thermal Solution
For thermal dissipation, a thermal solution enables the CEM700’s components to dissipate
heat efficiently. All heat generating components are thermally conducted to the heatsink in
order to avoid hot spots. Below images illustrate how to install the thermal solution on
CEM700.
1. There is a protective plastic covering on the thermal pads. This must be removed before
the heatsink can be mounted.
2. Each heatsink is designed for a specific CEM module. The thermal pads on the heatsink
are designed to make contact with the necessary components on the CEM module.
When mounting the heatsink you must make sure that the thermal pads on the heatsink
make complete contact (no space between thermal pad and component) with the
corresponding components on the CEM module. This is especially critical for CEM
modules that have higher CPU speeds (for example 1.0GHz or more) to ensure that the
heatsink acts as a proper thermal interface for cooling solutions.
3. This CPU module has six assembly holes for installing heatsink plate. Use screws to
secure heatsink plate to the CEM700. Be careful not to over-tighten the screws.

CEM700 COM ExpressTM Type 7 Basic Module
10 Module and Pin Assignments
2.4 Switch Settings
Properly configure switch settings on the CEM700 to meet your application purpose. Below
you can find a summary table of switch and onboard default setting.
Note
Once the default switch setting needs to be changed, please do it under power-off
condition.
Switch
Description
Setting
SW1
Auto Power On
Default: Disable
SW1-1 OFF
Restore BIOS Optimal Defaults
Default: Normal Operation
SW1-2 OFF
2.4.1 Auto Power On and Restore BIOS Optimal Defaults (SW1)
If dip1 of SW1 (SW1-1) is set to ON position, the system will be automatically power on
without pressing soft power button. If this switch is set to OFF position, it is necessary to
manually press soft power button to power on the system.
The dip2 of SW1 (SW1-2) is for restoring BIOS default status. Flip SW1-2 to ON position
for a few seconds then flip it back to OFF position. Doing this procedure can restore
BIOS optimal defaults.
Function
Setting
Disable auto power on (Default)
SW1-1 OFF
Enable auto power on
SW1-1 ON
Normal operation (Default)
SW1-2 OFF
Restore BIOS optimal defaults
SW1-2 ON

CEM700 COM ExpressTM Type 7 Basic Module
Module and Pin Assignments 11
2.5 Connector
Signals go to the other parts of the system through connectors. Loose or improper connection
might cause problems, please make sure all connectors are properly and firmly connected.
Here is a summary table which shows connectors on the hardware.
Connector
Description
SS1
COM ExpressTM Connector
SS2
COM ExpressTM Connector
DIMM1
Channel 1 DDR4 SO-DIMM Socket
DIMM2
Channel 0 DDR4 SO-DIMM Socket
Note
For single memory channel configuration, install memory module in channel 0
(DIMM2) DDR4 SO-DIMM socket.
For dual memory channel configuration, install memory modules of the same
size, chip width, density and rank in both channel 0 (DIMM2) and channel 1
(DIMM1) DDR4 SO-DIMM sockets.
2.5.1 COM ExpressTM Connectors (SS1 and SS2)
The following table shows pin assignments of the 220-pin COM ExpressTM connectors.

CEM700 COM ExpressTM Type 7 Basic Module
12 Module and Pin Assignments
Pin
Signal
Pin
Signal
Pin
Signal
Pin
Signal
A1
GND_A1 (FIXED)
B1
GND_B1 (FIXED)
C1
GND_C1 (FIXED)
D1
GND_D1 (FIXED)
A2
GBE0_MDI3-
B2
GBE0_ACT#
C2
GND_C2
D2
GND_D2
A3
GBE0_MDI3+
B3
LPC_FRAME#/ESPI_CS0#[2]
C3
USB_SSRX0-
D3
USB_SSTX0-
A4
GBE0_LINK100#
B4
LPC_AD0/ESPI_IO_0[2]
C4
USB_SSRX0+
D4
USB_SSTX0+
A5
GBE0_LINK1000#
B5
LPC_AD1/ESPI_IO_1[2]
C5
GND_C5
D5
GND_D5
A6
GBE0_MDI2-
B6
LPC_AD2/ESPI_IO_2[2]
C6
USB_SSRX1-
D6
USB_SSTX1-
A7
GBE0_MDI2+
B7
LPC_AD3/ESPI_IO_3[2]
C7
USB_SSRX1+
D7
USB_SSTX1+
A8
GBE0_LINK#
B8
LPC_DRQ0#/ESPI_ALERT0#[2]
C8
GND_C8
D8
GND_D8
A9
GBE0_MDI1-
B9
LPC_DRQ1#/ESPI_ALERT1#[2]
C9
USB_SSRX2-
D9
USB_SSTX2-
A10
GBE0_MDI1+
B10
LPC_CLK/ESPI_CLK[2]
C10
USB_SSRX2+
D10
USB_SSTX2+
A11
GND_A11 (FIXED)
B11
GND_B11 (FIXED)
C11
GND_C11 (FIXED)
D11
GND_D11 (FIXED)
A12
GBE0_MDI0-
B12
PWRBTN#
C12
USB_SSRX3-
D12
USB_SSTX3-
A13
GBE0_MDI0+
B13
SMB_CK
C13
USB_SSRX3+
D13
USB_SSTX3+
A14
GBE0_CTREF
B14
SMB_DAT
C14
GND_C14
D14
GND_D14
A15
SUS_S3#
B15
SMB_ALERT#
C15
10G_PHY_MDC_SCL3[1]
D15
10G_PHY_MDIO_SDA3[1]
A16
SATA0_TX+
B16
SATA1_TX+
C16
10G_PHY_MDC_SCL2[1]
D16
10G_PHY_MDIO_SDA2[1]
A17
SATA0_TX-
B17
SATA1_TX-
C17
10G_SDP2[1]
D17
10G_SDP3[1]
A18
SUS_S4#
B18
SUS_STAT#/ESPI_RESET#[2]
C18
GND_C18
D18
GND_D18
A19
SATA0_RX+
B19
SATA1_RX+
C19
PCIE_RX6+
D19
PCIE_TX6+
A20
SATA0_RX-
B20
SATA1_RX-
C20
PCIE_RX6-
D20
PCIE_TX6-
A21
GND_A21 (FIXED)
B21
GND_B21 (FIXED)
C21
GND_C21 (FIXED)
D21
GND_D21 (FIXED)
A22
PCIE_TX15+
B22
PCIE_RX15+
C22
PCIE_RX7+
D22
PCIE_TX7+
A23
PCIE_TX15-
B23
PCIE_RX15-
C23
PCIE_RX7-
D23
PCIE_TX7-
A24
SUS_S5#
B24
PWR_OK
C24
10G_INT2[1]
D24
10G_INT3[1]
A25
PCIE_TX14+
B25
PCIE_RX14+
C25
GND_C25
D25
GND_D25
A26
PCIE_TX14-
B26
PCIE_RX14-
C26
10G_KR_RX3+[1]
D26
10G_KR_TX3+[1]
A27
BATLOW#[1]
B27
WDT
C27
10G_KR_RX3-[1]
D27
10G_KR_TX3-[1]
A28
(S)ATA_ACT#
B28
RSVD_B28[1]
C28
GND_C28
D28
GND_D28
A29
RSVD_A29[1]
B29
RSVD_B29[1]
C29
10G_KR_RX2+[1]
D29
10G_KR_TX2+[1]
A30
RSVD_A30[1]
B30
RSVD_B30[1]
C30
10G_KR_RX2-[1]
D30
10G_KR_TX2-[1]
A31
GND_A31 (FIXED)
B31
GND_B31 (FIXED)
C31
GND_C31 (FIXED)
D31
GND_D31 (FIXED)
A32
RSVD_A32[1]
B32
SPKR
C32
10G_SFP_SDA3[1]
D32
10G_SFP_SCL3[1]
A33
RSVD_A33[1]
B33
I2C_CK
C33
10G_SFP_SDA2[1]
D33
10G_SFP_SCL2[1]
A34
BIOS_DIS0#/ESPI_SAFS
B34
I2C_DAT
C34
10G_PHY_RST_23[1]
D34
10G_PHY_CAP_23[1]
A35
THRMTRIP#
B35
THRM#[1]
C35
10G_PHY_RST_01
D35
10G_PHY_CAP_01
A36
PCIE_TX13+
B36
PCIE_RX13+
C36
10G_LED_SDA
D36
RSVD_D36[1]
A37
PCIE_TX13-
B37
PCIE_RX13-
C37
10G_LED_SCL
D37
RSVD_D37[1]
A38
GND_A38
B38
GND_B38
C38
10G_SFP_SDA1
D38
10G_SFP_SCL1
A39
PCIE_TX12+
B39
PCIE_RX12+
C39
10G_SFP_SDA0
D39
10G_SFP_SCL0
A40
PCIE_TX12-
B40
PCIE_RX12-
C40
10G_SDP0
D40
10G_SDP1
A41
GND_A41 (FIXED)
B41
GND_B41 (FIXED)
C41
GND_C41 (FIXED)
D41
GND_D41 (FIXED)
A42
USB2-
B42
USB3-
C42
10G_KR_RX1+
D42
10G_KR_TX1+
A43
USB2+
B43
USB3+
C43
10G_KR_RX1-
D43
10G_KR_TX1-
A44
USB_2_3_OC#
B44
USB_0_1_OC#
C44
GND_C44
D44
GND_D44
A45
USB0-
B45
USB1-
C45
10G_PHY_MDC_SCL1
D45
10G_PHY_MDIO_SDA1
A46
USB0+
B46
USB1+
C46
10G_PHY_MDC_SCL0
D46
10G_PHY_MDIO_SDA0
A47
VCC_RTC
B47
ESPI_EN#[1]
C47
10G_INT0
D47
10G_INT1
A48
RSVD_A48[1]
B48
USB0_HOST_PRSNT[1]
C48
GND_C48
D48
GND_D48
A49
GBE0_SDP
B49
SYS_RESET#
C49
10G_KR_RX0+
D49
10G_KR_TX0+
A50
LPC_SERIRQ/ESPI_CS1#[2]
B50
CB_RESET#
C50
10G_KR_RX0-
D50
10G_KR_TX0-
A51
GND_A51 (FIXED)
B51
GND_B51 (FIXED)
C51
GND_C51 (FIXED)
D51
GND_D51 (FIXED)
A52
PCIE_TX5+
B52
PCIE_RX5+
C52
PCIE_RX16+
D52
PCIE_TX16+
A53
PCIE_TX5-
B53
PCIE_RX5-
C53
PCIE_RX16-
D53
PCIE_TX16-
A54
GPI0
B54
GPO1
C54
TYPE0#
D54
RSVD_D54[1]
A55
PCIE_TX4+
B55
PCIE_RX4+
C55
PCIE_RX17+
D55
PCIE_TX17+
[1] Not connected on the CEM700.
[2] CEM700 doesn’t support ESPI. The voltage of these pins is 3.3V.

CEM700 COM ExpressTM Type 7 Basic Module
Module and Pin Assignments 13
Pin
Signal
Pin
Signal
Pin
Signal
Pin
Signal
A56
PCIE_TX4-
B56
PCIE_RX4-
C56
PCIE_RX17-
D56
PCIE_TX17-
A57
GND_A57
B57
GPO2
C57
TYPE1#[1]
D57
TYPE2#
A58
PCIE_TX3+
B58
PCIE_RX3+
C58
PCIE_RX18+
D58
PCIE_TX18+
A59
PCIE_TX3-
B59
PCIE_RX3-
C59
PCIE_RX18-
D59
PCIE_TX18-
A60
GND_A60 (FIXED)
B60
GND_B60 (FIXED)
C60
GND_C60 (FIXED)
D60
GND_D60 (FIXED)
A61
PCIE_TX2+
B61
PCIE_RX2+
C61
PCIE_RX19+
D61
PCIE_TX19+
A62
PCIE_TX2-
B62
PCIE_RX2-
C62
PCIE_RX19-
D62
PCIE_TX19-
A63
GPI1
B63
GPO3
C63
RSVD_C63[1]
D63
RSVD_D63[1]
A64
PCIE_TX1+
B64
PCIE_RX1+
C64
RSVD_C64[1]
D64
RSVD_D64[1]
A65
PCIE_TX1-
B65
PCIE_RX1-
C65
PCIE_RX20+
D65
PCIE_TX20+
A66
GND_A66
B66
WAKE0#
C66
PCIE_RX20-
D66
PCIE_TX20-
A67
GPI2
B67
WAKE1#
C67
RAPID_SHUTDOWN[1]
D67
GND_D67
A68
PCIE_TX0+
B68
PCIE_RX0+
C68
PCIE_RX21+
D68
PCIE_TX21+
A69
PCIE_TX0-
B69
PCIE_RX0-
C69
PCIE_RX21-
D69
PCIE_TX21-
A70
GND_A70 (FIXED)
B70
GND_B70 (FIXED)
C70
GND_C70 (FIXED)
D70
GND_D70 (FIXED)
A71
PCIE_TX8+
B71
PCIE_RX8+
C71
PCIE_RX22+
D71
PCIE_TX22+
A72
PCIE_TX8-
B72
PCIE_RX8-
C72
PCIE_RX22-
D72
PCIE_TX22-
A73
GND_A73
B73
GND_B73
C73
GND_C73
D73
GND_D73
A74
PCIE_TX9+
B74
PCIE_RX9+
C74
PCIE_RX23+
D74
PCIE_TX23+
A75
PCIE_TX9-
B75
PCIE_RX9-
C75
PCIE_RX23-
D75
PCIE_TX23-
A76
GND_A76
B76
GND_B76
C76
GND_C76
D76
GND_D76
A77
PCIE_TX10+
B77
PCIE_RX10+
C77
RSVD_C77[1]
D77
RSVD_D77[1]
A78
PCIE_TX10-
B78
PCIE_RX10-
C78
PCIE_RX24+
D78
PCIE_TX24+
A79
GND_A79
B79
GND_B79
C79
PCIE_RX24-
D79
PCIE_TX24-
A80
GND_A80 (FIXED)
B80
GND_B80 (FIXED)
C80
GND_C80 (FIXED)
D80
GND_D80 (FIXED)
A81
PCIE_TX11+
B81
PCIE_RX11+
C81
PCIE_RX25+
D81
PCIE_TX25+
A82
PCIE_TX11-
B82
PCIE_RX11-
C82
PCIE_RX25-
D82
PCIE_TX25-
A83
GND_A83
B83
GND_B83
C83
RSVD_C83[1]
D83
RSVD_D83[1]
A84
NCSI_TX_EN
B84
VCC_5V_SBY_1
C84
GND_C84
D84
GND_D84
A85
GPI3
B85
VCC_5V_SBY_2
C85
PCIE_RX26+
D85
PCIE_TX26+
A86
RSVD_A86[1]
B86
VCC_5V_SBY_3
C86
PCIE_RX26-
D86
PCIE_TX26-
A87
RSVD_A87[1]
B87
VCC_5V_SBY_4
C87
GND_C87
D87
GND_D87
A88
PCIE_CK_REF+
B88
BIOS_DIS1#
C88
PCIE_RX27+
D88
PCIE_TX27+
A89
PCIE_CK_REF-
B89
NCSI_RX_ER[1]
C89
PCIE_RX27-
D89
PCIE_TX27-
A90
GND_A90 (FIXED)
B90
GND_B90 (FIXED)
C90
GND_C90 (FIXED)
D90
GND_D90 (FIXED)
A91
SPI_POWER
B91
NCSI_CLK_IN
C91
PCIE_RX28+
D91
PCIE_TX28+
A92
SPI_MISO
B92
NCSI_RXD1
C92
PCIE_RX28-
D92
PCIE_TX28-
A93
GPO0
B93
NCSI_RXD0
C93
GND_C93
D93
GND_D93
A94
SPI_CLK
B94
NCSI_CRS_DV
C94
PCIE_RX29+
D94
PCIE_TX29+
A95
SPI_MOSI
B95
NCSI_TXD1
C95
PCIE_RX29-
D95
PCIE_TX29-
A96
TPM_PP
B96
NCSI_TXD0
C96
GND_C96
D96
GND_D96
A97
TYPE10#[1]
B97
SPI_CS#
C97
RSVD_C97[1]
D97
RSVD_D97[1]
A98
SER0_TX
B98
NCSI_ARB_IN
C98
PCIE_RX30+
D98
PCIE_TX30+
A99
SER0_RX
B99
NCSI_ARB_OUT
C99
PCIE_RX30-
D99
PCIE_TX30-
A100
GND_A100 (FIXED)
B100
GND_B100 (FIXED)
C100
GND_C100 (FIXED)
D100
GND_D100 (FIXED)
A101
SER1_TX
B101
FAN_PWNOUT
C101
PCIE_RX31+
D101
PCIE_TX31+
A102
SER1_RX
B102
FAN_TACHIN
C102
PCIE_RX31-
D102
PCIE_TX31-
A103
LID#
B103
SLEEP#
C103
GND_C103
D103
GND_D103
A104
VCC_12V_1
B104
VCC_12V_7
C104
VCC_12V_1
D104
VCC_12V_7
A105
VCC_12V_2
B105
VCC_12V_8
C105
VCC_12V_2
D105
VCC_12V_8
A106
VCC_12V_3
B106
VCC_12V_9
C106
VCC_12V_3
D106
VCC_12V_9
A107
VCC_12V_4
B107
VCC_12V_10
C107
VCC_12V_4
D107
VCC_12V_10
A108
VCC_12V_5
B108
VCC_12V_11
C108
VCC_12V_5
D108
VCC_12V_11
A109
VCC_12V_6
B109
VCC_12V_12
C109
VCC_12V_6
D109
VCC_12V_12
A110
GND_A110 (FIXED)
B110
GND_B110 (FIXED)
C110
GND_C110 (FIXED)
D110
GND_D110 (FIXED)
[1] Not connected on the CEM700.

CEM700 COM ExpressTM Type 7 Basic Module
14 Module and Pin Assignments
This page is intentionally left blank.