AXIOMTEK tBOX100-838-FL Series User manual

tBOX100-838-FL Series
Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make
any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
Copyright 2017 Axiomtek Co., Ltd.
All Rights Reserved
Aug 2017, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. User should not modify any unmentioned jumper settings without Axiomtek FAE’s
instruction. Any modifications without instruction might cause system damaged.
2. Operating system follows the configuration you had in tBOX100-838-FL.
3. Be sure to ground yourself to prevent static charge when installing internal
components. Using a grounding wrist strap and place all electronic components in
any static-shielded devices. Most electronic components are sensitive to static
electrical charge.
4. Disconnect the power input with tBOX100-838-FL before making any installation. Be
sure both the system and the external devices are TURNED OFF. Sudden surge of
power could damage sensitive components. Make sure the tBOX100-838-FL is
properly grounded.
5. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
6. TURN OFF the system power before cleaning.
7. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -40°C or above 60°C or It may damage the equipment.
8. Do not open the system’s bottom cover. If opening the cover for maintenance is a
must, only a trained technician is allowed to do so. Integrated circuits on computer
boards are sensitive to static electricity. To avoid damaging chips from electrostatic
discharge, observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.

iv
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IP40
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture
with air or with oxygen or nitrous oxide.
4. Mode of operation: Continuous
General Cleaning Tips
You may need the following precautions before you begin to clean the computer. When you
clean any single part or component for the computer, please read and understand the details
below fully.
When you need to clean the device, please rub it with a piece of dry cloth.
1. Be cautious of the tiny removable components when you use a vacuum cleaner to
absorb the dirt on the floor.
2. Turn the system off before you start to clean up the component or computer.
3. Never drop the components inside the computer or get circuit board damp or wet.
4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the
sake of cleaning. Some individuals may be allergic to the ingredients.
5. Try not to put any food, drink or cigarette around the computer.

v
Cleaning Tools:
Although many companies have created products to help improve the process of cleaning
your computer and peripherals users can also use household items to clean their computers
and peripherals. Below is a listing of items you may need or want to use while cleaning your
computer or computer peripherals.
Keep in mind that some components in your computer may only be able to be cleaned using
a product designed for cleaning that component, if this is the case it will be mentioned in the
cleaning.
Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, we still recommend
you to rub it with a piece of cloth.
Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or
rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the
plastics parts.
Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles
out of a computer can be one of the best methods of cleaning a computer. Over time
these items can restrict the airflow in a computer and cause circuitry to corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent
tools for wiping hard to reach areas in your keyboard, mouse, and other locations.
Foam swabs: Whenever possible it is better to use lint free swabs such as foam
swabs.
NOTE: We strongly recommended that you should shut down the system before you
start to clean any single components.
Please follow the steps below:
1. Close all application programs
2. Close operating software
3. Turn off power switch
4. Remove all device
5. Pull out power cable

vi
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible for the
suitable solution. For the computers that are no longer useful or no longer working well,
please contact your Axiomtek distributor for recycling and we will make the proper
arrangement.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI®is a registered trademark of American Megatrends Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Atom™are trademarks of Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

vii
Table of Contents
Disclaimers............................................................................................................. ii
Safety Precautions................................................................................................ iii
Classification......................................................................................................... iv
CHAPTER 1 INTRODUCTION.......................................................................1
1.1 General Description...........................................................................1
1.2 System Specifications.......................................................................2
1.2.1 CPU ...................................................................................................................2
1.2.2 System I/O ........................................................................................................2
1.2.3 System Specification.......................................................................................2
1.2.4 Driver CD Content............................................................................................3
1.3 Dimensions ........................................................................................4
1.4 I/O Outlets ..........................................................................................4
1.5 Packing List........................................................................................6
CHAPTER 2 HARDWARE INSTALLATION..................................................7
2.1 HDD/SSD Installation.........................................................................7
2.2PCI Express mini card and SIM card Installation............................. 8
2.3Wall mount kit Installation.................................................................9
CHAPTER 3 CONNECTOR .........................................................................11
3.1 Connectors....................................................................................... 11
3.1.1 VGA Connector..............................................................................................11
3.1.2 Remote switch Connector ............................................................................11
3.1.3 Serial Port Connector....................................................................................12
3.1.4 USB2.0 Stack Ports .......................................................................................12
3.1.5 LED Indicators................................................................................................13
3.1.6 DC Power Input connector............................................................................13
3.1.7 LAN Connector (LAN#1, LAN#2) ..................................................................14
3.1.8 SIM Card Connector ......................................................................................15
3.1.9 PCI Express mini card Connector................................................................16
CHAPTER 4 AMI BIOS SETUP UTILITY.....................................................17
4.1 Starting............................................................................................. 17
4.2 Navigation Keys............................................................................... 18
4.3 Main Menu ........................................................................................ 19
4.4 Advanced Menu ............................................................................... 20
4.5 Chipset Menu................................................................................... 27
4.6Security Menu .................................................................................. 29
4.7Boot Menu ........................................................................................30
4.8 Save & Exit Menu.............................................................................31
APPENDIX A WATCHDOG TIMER .............................................................33

viii
This page is intentionally left blank.

tBOX100-838-FL Series User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the tBOX100-838-FL.
The Chapter 1 includes the following sections:
General Description
System Specifications
Dimensions
I/O Outlets
Package List
1.1 General Description
The tBOX100-838-FL is an embedded system that supports onboard Intel®Atom™E3845
(1.91 GHz), to provide Windows®7, Windows®8, Windows®10 IoT, Windows®
embedded ,Linux and VxWorks7, suitable for the most endurable operation. It features
fanless design with full feature I/O, supports onboard 4GB DDR3L memory, and enhanced
system dependability by built-in Watchdog Timer.
Features
CE (Class A), E-Mark, ISO 7637, certified;
Intel®Bay Trail-I Atom™E3845 (10W) [email protected] processor onboard
DDR3 4GB system memory onboard comes with high performance and reliability
Fanless with operating temperature range of -40°C ~ +60°C
Intelligent power management solution
Compact size with rich multiple I/O ports, DIN rail and wall mount supported
1x full size PCI Express mini card slot, 1x SIM card socket for various applications
Reliable and Stable Design
The tBOX100-838-FL is designed for fanless and wide operating temperature range
system, also we enhance vibration endurance such as: lockable I/O outlets, onboard
processor, onboard system memory and follow IEC60068 regulartion, make sure
filed embedded system reliability and stability, best for mobility control unit,
passenger information system, onboard video surveillance and many more
applications.
Embedded O.S. Supported
The tBOX100-838-FL is not only support Windows®7/8/10, but also supports
embedded OS, such as Windows®7/8 embedded, WinCE, Linux and VxWorks7.
For storage device, the tBOX100-838-FL supports one 2.5" 9.5mm SATA HDD drive
bay.

tBOX100-838-FL Series User’s Manual
Introduction
2
1.2 System Specifications
1.2.1 CPU
CPU
Intel®Atom™E3845 processor (Quad Core, 2M Cache, 1.91 GHz) onboard.
BIOS
American Megatrends Inc. BIOS.
“Load Optimized Default” to backup customized Setting in the BIOS flash chip to
prevent from CMOS battery fail.
System Memory
4GB DDR3L-1333 system memory onboard.
Graphics
Integrated in the Intel®HD Graphics for VGA.
1.2.2 System I/O
Rear Side
2x RJ-45 GbE LAN (M12 A-coded is optional)
1x Phoenix DC power input (M12 DC power input is optional)
4x antenna opening
Front Side
1x RS-232/422/485
1x VGA
2x USB 2.0
1x Reset button
1x Remote power switch
4x video-in/1x audio-in BNC
1.2.3 System Specification
Watchdog Timer
Reset supported; 255 levels, 0~255 secs/mins
Power Supply
9~36 VDC-in power supply (Typical as +12/24V)
Power Rate:9-36Vdc, 1.8A@12/24Vdc
Operation Temperature
-40°C - +60°C (- 40°F - +140°F)
Storage Temperature
-40°C - +85°C (- 40°F - +176°F)
Humidity
5% - 95% (non-condensation)
Vibration Endurance
2Grms w/ SSD, (5 - 500Hz, X, Y, Z direction; Random)
1Grms w/ HDD, (5 –500Hz, X, Y, Z direction; Random)

tBOX100-838-FL Series User’s Manual
Introduction
3
Weight
0.77 kg (1.69 lb) without package
1.40 kg (2.78 lb) with package
Dimensions
163.8mm(6.44”)(W) x 108mm(4.25”)(D) x 44mm(1.73”)(H)
NOTE: All specifications and images are subject to change without notice.
1.2.4 Driver CD Content
Chipset Driver
Graphic Drivers
Ethernet Driver
Capture Card Driver

tBOX100-838-FL Series User’s Manual
Introduction
4
1.3 Dimensions
The following diagrams show you dimensions and outlines of the tBOX100-838-FL.

tBOX100-838-FL Series User’s Manual
Introduction
5
1.4 I/O Outlets
The following figures show you panoramic view of tBOX100-838-FL.
Front View
Front View drawing
Rear View type #1
Rear View drawing type #1

tBOX100-838-FL Series User’s Manual
Introduction
6
1.5 Packing List
The package bundled with your tBOX100-838-FL should contain the following items:
tBOX100-838-FL System Unit x 1
Quick Installation Guide x 1
DVD Driver x 1
Din-rail & Bracket x 1
Wall mount x 4
Foot Pad Kit x 4
Screws x 14 (SSD x4/Wall mount x4/Din rail x4/Mini card x2)
Terminal block for power x1 (RJ-45 GbE LAN version only)
HDD/SSD (optional)
M12 LAN cable (optional)
M12 power cable (optional)
M12 power adapter (optional)
Remote switch cable (optional)
Mmini card module (optional)
If you can not find this package or any items are missing, please contact Axiomtek distributors
immediately.

tBOX100-838-FL Series User’s Manual
Hardware Installation
7
CHAPTER 2
HARDWARE INSTALLATION
The tBOX100-838-FL is convenient for your various hardware configurations, such as HDD
and PCI Express mini card. The chapter 2 will show you how to install the components.
2.1 HDD/SSD Installation
Step 1 Turn off the system, and unplug the power cord. Loosen the screws and
plug out HDD/SSD tray as shown.
Step 2 Fasten 4x screw and rubber pad with HDD/SSD as shown.
Note the direction of SATA connector.
Step 3 Plug in HDD-TRAY and Fasten 2x screw as shown.

tBOX100-838-FL Series User’s Manual
Hardware Installation
8
2.2 PCI Express mini card and SIM card Installation
Step 1 Turn off the system, and unplug the power cord. Loosen the screws as
shown.
Step 2 Install the module card and fasten screw as shown.
Step 3 Fasten 4x screw on bottom cover as shown.

tBOX100-838-FL Series User’s Manual
Hardware Installation
9
2.3 Wall mount kit Installation
Step 1 Turn off the system, and unplug the power cord. Loosen the screws as
shown.
Step 2 Fasten 4x screw and wall mount kit, last fasten 2x screw as shown.

tBOX100-838-FL Series User’s Manual
Hardware Installation
10
2.4 Din-rail kit Installation
Step 1 Turn off the system, and unplug the power cord. Fasten 2x screw and din-
rail bracket.
Step 2 Fasten 2x screw and din-rail kit.

tBOX100-838-FL Series User’s Manual
Connector
11
CHAPTER 3
CONNECTOR
3.1 Connectors
Connectors connect the motherboard with other parts of the system. Loose or improper
connection might cause problems. Make sure all connectors are properly and firmly
connected.
3.1.1 VGA Connector
DB15 connector is commonly used for the CRT monitor.
Pin
Signal
Pin
Signal
Pin
Signal
1
Red
2
Green
3
Blue
4
N.C.
5
GND
6
GND
7
GND
8
GND
9
VCC
10
GND
11
N.C.
12
DDC DATA
13
Horizontal Sync
14
Vertical Sync
15
DDC CLK
3.1.2 Remote switch Connector
Remote switch is ideal for a remote botton which can act as an ATX power on/off botton.
Pin
Signal
Description
1
NC
2
Switch Signal
Low Active. Act as PC’s ATX switch when external switch
installed (Pin 3 Active)
**Internal pull up resister did not connect to any power
source
3
Ext. SW Sensor
Low Active. To detect external power swtich install or not.
** Internal pull up resister did not connect to any power
source
4
GND

tBOX100-838-FL Series User’s Manual
Connector
12
3.1.3 Serial Port Connector
The pin definitions of RS-232/422/485 are listed as following matrix. You may select RS-
232/422/485 function in BIOS settings.
Pin
RS-232
RS-422
RS-485
1
DCD, Data carrier detect
TX-
Data-
2
RXD, Receive data
TX+
Data+
3
TXD, Transmit data
RX+
NC
4
DTR, Data terminal ready
RX-
NC
5
GND, ground
GND, ground
GND, ground
6
DSR, Data set ready
NC
NC
7
RTS, Request to send
NC
NC
8
CTS, Clear to send
NC
NC
9
RI, Ring indicator
NC
NC
COM
3.1.4 USB2.0 Stack Ports
Pin
Signal USB Port 0
Pin
Signal USB Port 6
USB
1 2 3 4
5 6 7 8
1
USB VCC
(+5V level)
5
USB VCC
(+5V level)
2
USB #0_D-
6
USB #6_D-
3
USB #0_D+
7
USB #6_D+
4
Ground (GND)
8
Ground (GND)