Axis P3367-VE User manual

INSTALLATION GUIDE
AXIS P3346-VE Network Camera
AXIS P3367-VE Network Camera
AXIS P3384-VE Network Camera

Legal Considerations
Video and audio surveillance can be prohibited by laws that vary
from country to country. Check the laws in your local region
before using this product for surveillance purposes. This product
includes one (1) H.264 decoder license and one (1) AAC decoder
license. To purchase further licenses, contact your reseller.
Liability
Every care has been taken in the preparation of this
document. Please inform your local Axis office of any
inaccuracies or omissions. Axis Communications AB cannot
be held responsible for any technical or typographical errors
and reserves the right to make changes to the product and
manuals without prior notice. Axis Communications AB
makes no warranty of any kind with regard to the material
contained within this document, including, but not limited
to, the implied warranties of merchantability and fitness for
a particular purpose. Axis Communications AB shall not be
liable nor responsible for incidental or consequential
damages in connection with the furnishing, performance or
use of this material. This product is only to be used for its
intended purpose.
Intellectual Property Rights
Axis AB has intellectual property rights relating to
technology embodied in the product described in this
document. In particular, and without limitation, these
intellectual property rights may include one or more of the
patents listed at www.axis.com/patent.htm and one or more
additional patents or pending patent applications in the US
and other countries.
This product contains licensed third-party software. See the
menu item “About” in the product’s user interface for more
information.
This product contains source code copyright Apple Computer,
Inc., under the terms of Apple Public Source License 2.0 (see
www.opensource.apple.com/apsl). The source code is
available from https://developer.apple.com/bonjour/
Equipment Modifications
This equipment must be installed and used in strict
accordance with the instructions given in the user
documentation. This equipment contains no user-serviceable
components. Unauthorized equipment changes or
modifications will invalidate all applicable regulatory
certifications and approvals.
Trademark Acknowledgments
AXIS COMMUNICATIONS, AXIS, ETRAX, ARTPEC and VAPIX are
registered trademarks or trademark applications of Axis AB in
various jurisdictions. All other company names and products are
trademarks or registered trademarks of their respective
companies. Apple, Boa, Apache, Bonjour, Ethernet, Internet
Explorer, Linux, Microsoft, Mozilla, Real, SMPTE, QuickTime,
UNIX, Windows, Windows Vista and WWW are registered
trademarks of the respective holders. Java and all Java-based
trademarks and logos are trademarks or registered trademarks of
Oracle and/or its affiliates. UPnPTM is a certification mark of the
UPnPTM Implementers Corporation.
Regulatory Information
Europe
This product complies with the applicable CE marking
directives and harmonized standards:
• Electromagnetic Compatibility (EMC) Directive
2004/108/EC. See Electromagnetic Compatibility (EMC).
• Low Voltage (LVD) Directive 2006/95/EC. See Safety.
• Restrictions of Hazardous Substances (RoHS) Directive
2011/65/EU. See Disposal and Recycling.
A copy of the original declaration of conformity may be obtained
from Axis Communications AB. See Contact Information.
Electromagnetic Compatibility (EMC)
This equipment has been designed and tested to fulfill
applicable standards for:
• Radio frequency emission when installed according to the
instructions and used in its intended environment.
• Immunity to electrical and electromagnetic phenomena
when installed according to the instructions and used in its
intended environment.
USA
Using an unshielded network cable (UTP) - AXIS P3367-VE
and AXIS P3384-VE have been tested using an unshielded
network cable (UTP) and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
Using a shielded network cable (STP) – AXIS P3346-VE, AXIS
P3367-VE and AXIS P3384-VE have been tested using a
shielded network cable (STP) and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
To be used in a residential area or a demanding electrical
environment, the product shall be connected using a shielded
network cable (STP) that is properly grounded.
Canada
This digital apparatus complies with CAN ICES-3 (Class B). The
product shall be connected using a shielded network cable (STP)
that is properly grounded.
Cet appareil numérique est conforme à la norme CAN NMB-3
(classe B). Le produit doit être connecté à l'aide d'un câble
réseau blindé (STP) qui est correctement mis à la terre.
Europe
This digital equipment fulfills the requirements for RF emission
according to the Class B limit of EN 55022. The product shall be
connected using a shielded network cable (STP) that is properly
grounded.
This product fulfills the requirements for immunity according to
EN 61000-6-1 residential, commercial and light-industrial
environments.
This product fulfills the requirements for immunity according to
EN 55024 office and commercial environments.
Australia/New Zealand
This digital equipment fulfills the requirements for RF
emission according to the Class B limit of AS/NZS CISPR 22.
The product shall be connected using a shielded network
cable (STP) that is properly grounded.

Safety
This product complies with IEC/EN 60950-1, Safety of
Information Technology Equipment. If its connecting cables are
routed outdoors, the product shall be grounded either through a
shielded network cable (STP) or other appropriate method.
Disposal and Recycling
When this product has reached the end of its useful life, dispose
of it according to local raws and regulations. For information
about your nearest designated collection point, contact your
local authority responsible for waste disposal. In accordance
with local legislation, penalties may be applicable for incorrect
disposal of this waste.
Europe
This symbol means that the product shall not be
disposed of together with household or commercial
waste. Directive 2012/19/EU on waste electrical and
electronic equipment (WEEE) is applicable in the
European Union member states. To prevent potential
harm to human health and the environment, the product must
be disposed of in an approved and environmentally safe
recycling process. For information about your nearest designated
collection point, contact your local authority responsible for
waste disposal. Businesses should contact the product supplier
for information about how to dispose of this product correctly.
This product complies with the requirements of Directive
2011/65/EU on the restriction of the use of certain hazardous
substances in electrical and electronic equipment (RoHS).
China
This product complies with the requirements of the
legislative act Administration on the Control of
Pollution Caused by Electronic Information Products
(ACPEIP).
Contact Information
Axis Communications AB
Emdalavägen 14
223 69 Lund
Sweden
Tel: [phone]
Fax: [phone]
www.axis.com
Support
Should you require any technical assistance, please contact your
Axis reseller. If your questions cannot be answered immediately,
your reseller will forward your queries through the appropriate
channels to ensure a rapid response. If you are connected to the
Internet, you can:
• download user documentation and software updates
• find answers to resolved problems in the FAQ database.
Search by product, category, or phrase
• report problems to Axis support staff by logging in to your
private support area
Japan - この装置は、クラスB情報技術装置です。
この装置は、家庭環境で使用することを目的として
いますが、この装置がラジオやテレビジョン受信機
に近接して使用されると、受信障害を引き起こすこ
とがあります。取扱説明書に従って正しい取り扱い
をして下さい。本製品は、シールドネットワーク
ケーブル(STP)を使用して接続してください。また
適切に接地してください。
Korea - ࢇЕɼࢽࡈ%ࢷ࢕ળࢶଢԻ۰
࣯Իɼࢽ߾۰یࡈଜЕʨࡶּࢶࡳԻଜֲֻҘ
ࠇ߾۰یࡈଟܹ࢑ݡТЬࢶࢸ஢ࢻѹ673
VKLHOGHGWZLVWHGSDLUৼࢇٴࡶیࡈଜࠆࢿ૽
ࡶࠉʼଜݫݤࠝ
• chat with Axis support staff (selected countries only)
• visit Axis Support at www.axis.com/techsup/
Should you require any technical assistance, please contact
appropriate channels according to your AVHS license
agreement to ensure a rapid response.
Learn More!
Visit Axis learning center www.axis.com/academy/ for useful
trainings, webinars, tutorials and guides.

AXIS P33-VE Series Installation Guide Page 5
Safety Information
Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for
future reference.
Hazard Levels
Other Message Levels
Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not
avoided, could result in minor or moderate
injury.
Indicates a situation which, if not avoided,
could result in damage to property.
Indicates significant information which is
essential for the product to function correctly.
Indicates useful information which helps in
getting the most out of the product.

Page 6 AXIS P33-VE Series Installation Guide
Safety Instructions
• The Axis product shall be installed by a trained professional.
• The Axis product shall be used in compliance with local laws and regulations.
• Store the Axis product in a dry and ventilated environment.
• Avoid exposing the Axis product to shocks or heavy pressure.
• Do not install the product on unstable brackets, surfaces or walls.
• Use only applicable tools when installing the Axis product. Excessive force could cause damage to
the product.
• Do not use chemicals, caustic agents, or aerosol cleaners. Use a clean cloth dampened with pure
water for cleaning.
• Use only accessories that comply with technical specification of the product. These can be provided
by Axis or a third party.
• Use only spare parts provided by or recommended by Axis.
• Do not attempt to repair the product by yourself. Contact Axis support or your Axis reseller for
service matters.
Transportation
• Keep the protective packaging. When transporting the Axis product, the protective packaging shall
be replaced in its original position.
• When transporting the Axis product, use the original packaging or equivalent to prevent damage to
the product.

AXIS P33-VE Series Installation Guide Page 7
Battery
The Axis product uses a 3.0 V BR/CR2032 lithium battery as the power supply for its internal real-
time clock (RTC). Under normal conditions this battery will last for a minimum of five years.
Low battery power affects the operation of the RTC, causing it to reset at every power-up. When
the battery needs replacing, a log message will appear in the product’s server report. For more
information about the server report, see the product’s setup pages or contact Axis support.
The battery should not be replaced unless required, but if the battery does need replacing, contact
Axis support at www.axis.com/techsup for assistance.
• Risk of explosion if the battery is incorrectly replaced.
• Replace only with an identical battery or a battery which is recommended by Axis.
• Dispose of used batteries according to local regulations or the battery manufacturer's instructions.
Dome Cover
• Be careful not to scratch, damage or leave fingerprints on the dome cover because this could
decrease image quality. If possible, keep the protective plastic on the dome cover until the
installation is complete.
• Do not clean a dome cover that looks clean to the eye and never polish the surface. Excessive
cleaning could damage the surface.
• For general cleaning of the dome cover it is recommended to use a non-abrasive, solvent-free neutral
soap or detergent mixed with pure water and a soft, clean cloth. Rinse well with pure lukewarm
water. Dry with a soft, clean cloth to prevent water spotting.
• Never use harsh detergents, gasoline, benzene or acetone etc and avoid cleaning the dome cover in
direct sunlight or at elevated temperatures.

Page 8 AXIS P33-VE Series Installation Guide
Installation Guide
This guide helps you to install the AXIS P33-VE Series on your network. For further information,
please see the User Manual available on the CD, or from www.axis.com/techsup
Follow these instructions to install the network camera
1. Package Contents, on page 9
2. Hardware Overview, on page 10
3. Install the Hardware, on page 15
4. Access the Product, on page 20
5. Adjust the Lens, on page 20
6. Complete the Installation, on page 22
• Before you begin, make sure that the package contents, power supply, and the required cables, tools,
and documentation are available. See Package Contents below.
• This network camera is intended to operate with PoE; if not available use Axis PoE Midspan 1 port
(not included)
Important!
This product must be used in
compliance with local laws and
regulations.

AXIS P33-VE Series Installation Guide Page 9
Package Contents
Item Models/variants/notes
Network camera
with heating module
AXIS P3346-VE
AXIS P3367-VE
AXIS P3384-VE
Mounting bracket
Dome covers Clear transparent cover
Smoked transparent cover
Weather shield
Labels 2 adhesive serial no. labels
Mounting kit Resitorx screw driver, drill template, 5-meter network cable with gasket
4 screws and plugs, 2 long screws, 2 M4x8 screws
1 gasket, terminal block connector
CD AXIS Network Video Product CD including product documentation,
installation tools and other software
Printed Materials Installation Guide (this document)
Axis Warranty Document
AVHS Authentication key
Optional accessories See www.axis.com for information on available accessories

Page 10 AXIS P33-VE Series Installation Guide
Hardware Overview
The heater in the camera unit may be hot.
Dimension (HxW)
AXIS P3346-VE = 117 x 179 mm (4.59” x 7.05”)
AXIS P3367-VE = 117 x 179 mm (4.59” x 7.05”)
AXIS P3384-VE = 117 x 179 mm (4.59” x 7.05”)
Weight
AXIS P3346-VE = 1.6 kg (3.5 lb)
AXIS P3367-VE = 1.6 kg (3.5 lb)
AXIS P3384-VE = 1.6 kg (3.5 lb)
Fan output
connector
Unit casing
Camera unit
Dome cover
Holes for cables
routed through the wall
Side holes with
Network connector
LED indicators
Control button
Camera unit
Audio in
(PoE)
Audio out
SD memory card slot
Serial no.
Heater
Weather shield
Spring
routed along the wall
for cablesgaskets
I/O connector
Mounting bracket

AXIS P33-VE Series Installation Guide Page 11
LED Indicators
LED Color Indication
Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.
Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.
Unlit No network connection.
Status Green Steady green for normal operation.
Amber Steady during startup; flashes once during reset to factory default or while
restoring settings.
Red Slow flash for failed upgrade.
Power Green Normal operation.
Amber Flashes green/amber during firmware upgrade.

Page 12 AXIS P33-VE Series Installation Guide
Connectors
Network Connector
AXIS P3367-VE and AXIS AXIS P3384-VE:
Due to local regulations or the environmental and electrical conditions in which the
product is to be used, a shielded network cable (STP) may be appropriate or required. All
cables connecting the product to the network and that are routed outdoors or in
demanding electrical environments shall be intended for their specific use. Make sure that
the network devices are installed in accordance with the manufacturer’s instructions. For
information about regulatory requirements, see Regulatory Information, on page 2.
AXIS P3346-VE:
The product shall be connected using a shielded network cable (STP). All cables connecting
the product to the network shall be intended for their specific use. Make sure that the
network devices are installed in accordance with the manufacturer’s instructions. For
information about regulatory requirements, see Regulatory Information, on page 2.
• RJ-45 Ethernet connector. Supports Power over Ethernet.
Audio Connectors
•Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is
used from a stereo signal).
•Audio out - Audio output (line level) that can be connected to a public address (PA) system
or an active speaker with a built-in amplifier. A pair of headphones can also be attached. A
stereo connector must be used for the audio out.
SD Card Slot
•SDHC memory card slot - The high capacity SD memory card can be used for local record-
ing with removable storage.

AXIS P33-VE Series Installation Guide Page 13
I/O Connectors
•I/O terminal connector - Used in applications for e.g. motion detec-
tion, event triggering, time lapse recording and alarm notifications.
In addition to an auxiliary power and a GND pin, it provides the
interface to:
• 1 transistor output - For connecting external devices such as relays
and LEDs. Connected devices can be activated by the VAPIX® Application Programming
Interface (API), by the output buttons on the Live View page or by an Action Rule. The out-
put will show as active (shown under System Options > Ports & Devices) if the alarm device
is activated.
• 1 digital input - An alarm input for connecting devices that can toggle between an open
and closed circuit, for example: PIRs, door/window contacts, and glass break detectors.
When a signal is received the state changes and the input becomes active (shown under
System Options > Ports & Devices).
Function Pin Notes Specifications
GND 1 Ground
3.3V DC
Power
2 Can be used to power auxiliary equipment.
Note: This pin can only be used as power out.
Max. load = 50mA
Digital
Input
3 Connect to GND to activate, or leave floating (or
unconnected) to deactivate.
Min. input= - 40V DC
Max. input= + 40V DC
Digital
Output
4 Uses an open-drain NFET transistor with the source
connected to GND. If used with an external relay, a
diode must be connected in parallel with the load,
for protection against voltage transients.
Max. load = 100mA
Max voltage = + 40V DC
Pin1
Pin2
Pin3
Pin4

Page 14 AXIS P33-VE Series Installation Guide
The following connection diagram gives an example of how to connect an auxiliary device to the
AXIS P3346-VE/P3367-VE/P3384-VE.
1
2
E.g. push button
3
4
3.3V
max. 50mA
D
S
G

AXIS P33-VE Series Installation Guide Page 15
Install the Hardware
Please remove the rubber band for transport-safety from the camera unit before you mount
the camera.
Prepare the Network Cable
For network cable specifications, see Network Connector, on page 12.
If a cable other than the provided cable is used, you need to prepare a network cable with a gasket.
Gently force the cable through the gasket provided and attach a network connector. It may be
necessary to pierce a hole in the gasket with the resitorx screwdriver.
• Do not force the network connector into the gasket.
• Do not pierce the gasket with a knife or other sharp object.

Page 16 AXIS P33-VE Series Installation Guide
Prepare the Unit Casing (routing cables along the wall)
If the cables are to be routed along the wall, prepare the unit casing as follows:
1. Detach the side lid that is attached to the unit casing by removing the screw.
2. Loosen the two screws on the cable shield and detach the bottom part.
3. Attach the bottom part of the cable shield to the unit casing with the screw.
Replace Clear/Smoked Dome Cover (optional)
The AXIS P3346-VE/P3367-VE/P3384-VE is supplied with an optional dome.
To replace the dome cover:
1. Loosen the 4 screws under the dome cover that hold the dome in place.
2. Replace the old dome with the new and tighten the screws.
Mounting Bracket
The mounting plate has 4 mounting hole patterns (A,B,C,D).
The mounting hole patterns follow standard for the following
mounting options:
• A: 4" square box
• B: standard-sized US double gang junction box
• C: 4" octagon box
• D: standard-sized US single gang junction box
Side lid
Screw
Top part
Bottom part
Unit casing Cable shield Unit casing

AXIS P33-VE Series Installation Guide Page 17
Route the Cables
Depending on whether you want to route the cables through or along the wall, follow the relevant
instructions below.
Routing Cables along the Wall
1. Using the drill template drill 4 holes in the wall.
2. Attach the mounting bracket to the wall using the 4 screws provided, or screws appropriate for
the wall material.
3. Remove the camera unit from the unit casing by pushing the springs aside.
4. Remove the gaskets from the side holes in the unit casing. If there is only one cable, remove
only one gasket.
5. Place the unit casing on the mounting bracket and attach it by tightening the four screws.
6. Pull the cables up through the side holes in the unit casing.
7. Drag the gaskets along the cable and plug them into the holes. The gaskets should fit snugly in
the holes with no folds or bends.
8. Re-attach the top part of the cable shield by tightening the two screws.
To avoid moisture-related problems it is recommended that the cables are routed to the
camera from below with the cable holes facing downwards.
Routing Cables through the Wall
1. Using the drill template drill 4 holes in the wall.
2. Route the network cable (and the I/O, audio cable if necessary) through the wall and through
the holes in the mounting bracket.
3. Attach the mounting bracket to the wall using the 4 screws provided, or screws appropriate for
the wall material.
4. Remove the camera unit from the unit casing by pushing the springs aside.
5. Remove the gaskets from the back holes in the unit casing. If there is only one cable, remove
only one gasket.
6. Route the cables through these holes.
7. Drag the gaskets along the cables and plug them into the holes. The gaskets should fit snugly in
the holes with no folds or bends.

Page 18 AXIS P33-VE Series Installation Guide
8. Attach the unit casing to the
mounting bracket by tightening
the four screws.
Mounting bracket
Network cable with gasket
Unit casing
Remove gaskets
from holes

AXIS P33-VE Series Installation Guide Page 19
Install the Camera Unit
1. Attach the network cable to the camera unit; and the cable for audio and I/O if required. It is
recommended that the network cable is twisted to a loop as shown in the illustration above.
Be careful not to stretch or bend the network cable too much since this could cause
damage to the network cable.
2. Insert the SD memory card (optional).
3. Pull aside the springs in the unit casing and click the camera unit in place.
4. Attach the fan connector to the connector in the camera unit.
5. Attach the two M4x8 20 screws to the camera for greater stability.
These screws are only necessary to secure against heavy shocks and vibrations.
Connector for fan
Camera unit
Network cable
Attach
screw to camera

Page 20 AXIS P33-VE Series Installation Guide
The AXIS P3346-VE/P3367-VE/P3384-VE
can also be fitted with a metal conduit for
protecting the cabling when cables are routed along
the wall.
Conduit