Axis 140 BJC User manual

Quick Installation Guide
This guide covers the installation and basic setup procedures for the
AXIS PrintPoint 140 BJC. If you need more detailed instructions,
please refer to the AXIS PrintPoint 140 BJC User’s Manual.
Physical Description
Installing AXIS PrintPoint 140 BJC
You should proceed with the following instructions, as appropriate
for your type of network. Refer to all relevant sections if you intend
to use the AXIS PrintPoint 140 BJC in a multiprotocol
environment.
Hardware Installation
1. Note the serial number found on the underside label of the AXIS
PrintPoint 140 BJC. You need this number during the
configuration.
2. Switch off the printer and plug the AXIS PrintPoint 140 BJC
into the printer’s parallel port.
3. Connect the AXIS PrintPoint 140 BJC to the network using an
appropriate Ethernet cable.
4. Switch on the printer and connect the external power supply to
the AXIS PrintPoint 140 BJC. Ensure that the Network
Indicator is flashing.
5. Successful output of a Test Page will effectively confirm that the
unit has been connected correctly. Press the Test Button to print
a Test Page.
External Power
Supply Connector
Ethernet
10baseT
Connector Test Button
LPT1 Printer
Connector
Network Indicator
Power Indicator

NetWare
By following the instructions detailed below, install your AXIS
PrintPoint 140 BJC with the AXIS NetPilot™ Installation Wizard,
supplied on the AXIS Utilities Diskette. Please note that AXIS
NetPilot™ software requires a Windows platform that uses
NetWare or NetBIOS/NetBEUI.
1. Load the AXIS NetPilot™ software by following the instructions
on the label of the AXIS Utilities diskette. After loading the
software, double-click on the AXIS NetPilot™ icon. AXIS
NetPilot™ then scans the network for all connected Axis
Network Print Servers.
2. AXIS Units previously installed using the AXIS NetPilot™
appear as ‘Network Print Servers’ and un-installed units are
featured as ‘New Axis Units’. Select your AXIS PrintPoint 140
BJC from the ‘New Axis Units’ sub-folder and then click on the
Install icon. The Installation Wizard guides you through the
basic installation.
Click the Help icon should you require assistance throughout any
stage of the operation.
To set up print queues:
1. Open the ‘Network Print Servers’ folder and select the Network
Print Server you wish to setup.
2. Choose ‘Network’ from the Toolbar or Setup menu.
3. A new ‘Network environments’ window will now be open. From
this window you may create new print queues, connect to
previously established queues, and/or select the mode of
operation (Print Server or Remote Printer) for each printer.
To set up the advanced operating parameters:
1. Open the ‘Network Print Servers’ folder and select the Network
Print Server you wish to setup.
2. Choose Properties from the Toolbar or Setup menu.
3. A set of ‘tabbed’ Property Pages will open which allow you to
refine the chosen mode of operation, e.g. password protection,
frame type selection and/or setting of the queue polling interval.
The NetWare Configuration is now complete and you can close the
AXIS NetPilot™.
To verify that the AXIS PrintPoint 140 BJC is functioning correctly,
we recommend that you print a document from within a Windows
application, e.g. Microsoft Word. Please ensure that your printer is
selected as the Active Printer.
NetWare

Windows
Supplied on the AXIS Utilities diskette, the AXIS Print Monitor
should be used for network printing within Windows 95 and
Windows NT environments. It allows AXIS Network Print Servers
to be connected in the same simple fashion as a local printer port and
once installed, is automatically initialized upon system startup.
The AXIS Print Utility for Windows is also supplied on the AXIS
Utilities diskette and is the tool for network printing within
Windows for Workgroups and Windows 3.1 environments.
Follow the instructions on the AXIS Utilities diskette label to install
the appropriate printing tool for your environment.
Windows 95 and NT
The AXIS Print Monitor needs to be installed on each workstation
performing peer-to-peer printing. Once installed, the AXIS Print
Monitor then allows users to access to all network printers, just as if
they were connected directly to their workstation.
Peer-to-peer printing:
Although the AXIS Print Monitor user dialog will vary slightly
dependent upon which platform you are using, Windows 95 or
Windows NT, the functionality of the two variants is exactly the
same. Follow the procedure below to install Axis printer ports:
1. To start the Add Printer Wizard, select Settings - Printers from
the Start Menu and double-click on the Add Printer icon.
2. After clicking Next> in the first dialog the Wizard will ask you
to select between Local Printer/My Computer (Windows 95/
NT) and Network Printer. Select Local Printer/My Computer.
3. Choose an appropriate print driver for your printer. If the
desired print driver already appears within the displayed
manufacturer and model lists dialog, click Next> and proceed
to step 6.
4. Click the Have Disk... button. Insert the print driver diskette
into the floppy disk drive of your computer. If the floppy disk
drive is A:/ then click OK, otherwise type the letter of your disk
drive and then click OK.
5. Select the desired printer you want to install from the diskette
and click Next>.
6. Select the AXIS PrintPoint 140 BJC port to be installed. The
port appears as <name>.LP1, where <name> is AX followed by
last six digits of the AXIS PrintPoint 140 BJC serial number.
For example: AX560B35.
7. Click on the Configure Port button and choose when Pop-up
messages are to displayed from the Configure AXIS Printer
Ports dialog. Check the appropriate boxes and then click
Next>.

8. Enter an appropriate name for your printer and click Next>
9. Choose whether you wish to produce a Test Page and then
click Finish.
Client-server printing:
The AXIS Print Monitor is not needed on the client platforms for
client-server printing.
Windows 3.1 and Windows for Workgroups
All Windows 3.1 and Windows for Workgroups users requiring
access to a network printer in peer-to-peer mode, will need to install
the AXIS Print Utility for Windows onto their workstations.
Client-server printing:
This print method is suitable for larger networks and require only
one user to install the AXIS Print Utility for Windows software onto
their workstation. The setup procedure is described below:
1. Install AXIS Print Utility for Windows onto the file server.
2. Setup your AXIS PrintPoint 140 BJC from the file server as
described in the peer-to-peer printing section below, but
additionally check the Share box for your printer.
Your shared printers can now be used by all the Windows clients and
do not need to install the AXIS Print Utility on the clients.
Important note:
The server setup described above should only be made on a
Windows for Workgroup workstation.
Peer-to-Peer printing:
This print method does not require a file server and is recommended
for smaller networks. Follow these steps to install your AXIS
PrintPoint 140 BJC for peer-to-peer printing at a Windows for
Workgroups or Windows 3.1 workstation:
1. Double-click the AXIS Print Utility icon.
2. In the Port menu, click Add.
3. In the NPS Port list, select the AXIS PrintPoint 140 BJC port to
be installed. The port appears as <name>.LP1, where <name> is
AX followed by last six digits of your print server number. For
example: AX100086.LP1.
Note that this alphanumeric name will be superseded by any new
name given to your AXIS PrintPoint 140 BJC when using AXIS
NetPilot™.
4. Accept or change the suggested Windows port name, and type
any comments in the Description field. Make a note of the
Windows port name as you will need it later. Click OK to install
the Windows port.
5. In the Port menu, click Connect to bring up the Windows
Printers dialog.

6. Select a printer driver from the list of Installed Printers, or click
Add>> to install a new driver. Click Connect...
7. Select the Windows port name defined in step 4 above that
should now feature at the bottom of the Ports list.
8. Click OK to close the Connect dialog, and Close to close Printers.
The setup is now completed and you can print through your AXIS
PrintPoint 140 BJC.
Important: Windows 3.1 will require network support such as LAN
Server or LAN Manager Workstation software to be installed in
order to redirect a local printer port to a network device.
Important: AXIS Print Utility for Windows must be running when
you print through your AXIS PrintPoint 140 BJC. We strongly
recommend that you copy the AXIS Print Utility icon into your
StartUp folder.
Windows Clients using LANtastic
From any Windows client, the AXIS PrintPoint 140 BJC may also
be used for network printing within LANtastic environments. Your
choice of Axis utility software should be guided by type of Windows
client employed. Simply refer to the appropriate Windows Section
for your client above. Please ensure that your LANtastic client is
running NetBIOS/NetBEUI.
OS/2
Firstly, ensure that the NetBEUI protocol is active. If necessary, use
MPTS/LAPS (LAN Server) to activate it.
Load AXIS Print Utility for OS/2 and Install your AXIS PrintPoint
140 BJC:
1. Insert the OS/2 Utilities diskette into your disk drive, and open
an OS/2 window. Execute the install.exe program.
2. With the AXIS Print Utility for OS/2 running, install your AXIS
PrintPoint 140 BJC by clicking Install. The port appear as
<name>.LP1, where <name> is AX followed by last six digits of
the AXIS PrintPoint 140 BJC serial number. For example:
AX100086.LP1. Note that this alphanumeric name will be
superseded by any new name given to your AXIS PrintPoint 140
BJC when using AXIS NetPilot™.
3. Select the port you want to install, then click Install.
Repeat this procedure for each server using the AXIS PrintPoint 140
BJC.
Create a Print Queue (OS/2 version 1.x):
1. Double-click the Print Manager icon, click Setup, then select
Printers...
2. Click Add to make a new printer definition, then type a name of
your choice in the Name field.

3. Select \PIPE\<name>.LP1 from the Device list, then select a
printer driver suitable for your printer.
4. Click Add, then click OK to confirm the printer definition.
5. Click Setup, then select Queues...
6. Click Add to create a print queue. Type a name in the Name
field.
7. Click Add, then click OK to confirm the queue definition.
Create a Print Queue (OS/2 version 2.x and OS/2 Warp):
1. Double-click the Templates folder, then drag the Printer icon out
to the Workplace Shell (or into a folder) while holding the right
mouse button down.
2. Type a name of your choice in the Name field.
3. Select \PIPE\<name>.LP1 from the Port list, and select a printer
driver suitable for your printer from the Standard Printer list.
4. Click OK to confirm the printer definition.
Print queue sharing:
Open an OS/2 window and issue the following command:
NET SHARE queue_name /PRINT, where queue_name is the
name of the queue to be created.
Important note: AXIS Print Utility for OS/2 must be running when
you print through your AXIS PrintPoint 140 BJC. We strongly
recommend that you copy the AXIS Print Utility icon into your
StartUp file.
Web Based management
After setting the Internet Address and Host Name in the AXIS
PrintPoint 140 BJC, as described in the User’s Manual, you are then
able to access your AXIS PrintPoint 140 BJC from any standard
Web browser. To do this simply enter the Internet Address of the
AXIS PrintPoint 140 BJC as a URL in your browser, as follows:
http://192.36.253.96, or
http://salesdept
The Home Page of the AXIS PrintPoint 140 BJC will now be
displayed in your browser, where links to the AXIS PrintPoint 140
BJC Configuration, Management, Status, Account, Printer and
Help services are readily available.

AxisCommunications
URL:http://www.axis.com/
Lund
Phone:[phone]
Boston
Phone:[phone]AXIS
Paris
Phone:[phone]
London
Phone:[phone]
Tokyo
Phone:[phone]
Singapore
Phone:[phone]
HongKong
Phone:[phone]
Beijing
Phone:[phone]
Shanghai
Phone:[phone]
Taipei
Phone:[phone]
Seoul
Phone:[phone]
AXIS PrintPoint 140 BJC Quick Installation Guide
PartNo:15624
Revision: 1.0 Date: September 1997
Copyright © Axis Communications AB, 1996-1997