Axis 70 User manual

AXIS 70/70U User’s Guide 1
AXIS 70/70U
Network Document Server
User’s Guide

AXIS COMMUNICATIONS
<Product Name> Quick User’s Guide
AXIS 70/70U User’s Guide
2
About This Document
This guide applies to the AXIS 70 and AXIS 70U Network
Document Server with software release 1.00 and subsequent
releases until otherwise notified.
The document provides introductory information as well as
instructions on how to set up and manage the AXIS 70/70U. It is
intended for anyone involved in installing and using the AXIS
70/70U.Formoredetailedinstructions,refertoapplicablepartsof
the AXIS 70/70U/7000 User’s Manual that is available from the
Axis Web site and from the AXIS Network Product CD.
Safety Notices
Take some time to read through the safety notices before
installing the AXIS 70/70U.Please observe all safety markings and
instructions when using this product.
Caution! - must be observed to avoid loss of data or damage
to your equipment.
Important: - must be observed to avoid operational
impairment.
Do not proceed beyond any of the above notices, until you have
fully understood the implications.
Copyright Information
The unauthorized copying of materials that are covered by
copyright and other international proprietary or intellectual
property rights is prohibited in most countries. Axis
Communications AB recommends that the users of this
equipment seek the necessary authorizations for copying
material. The instructions for use in the manual shall not be
considered as an inducement to make illicit duplications of
material. Any duplication will be made at the user’s own risk.
Electromagnetic Compatibility (EMC)
USA - This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
Shielded (STP) network cables must be used with this unit to
ensure compliance with the class B limits.
Europe - Thisdigitalequipmentfulfilstherequirementsforradiated
emission according to limit B of EN55022, and the requirements for
immunity according to EN55024 residential, commercial, and light
industry (Compliance is not valid for unshielded network cables)
Japan - This is a class B product based on the standard of the
Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television
receiver in a domestic environment, it may cause radio interference.
Install and use the equipment according to the instruction manual.
Australia - This electronic device meets the requirements of the
Radiocommunications(ElectromagneticCompatibility)Standard 1998
AS/NZS 3548.
Liability
Every care has been taken in the preparation of this manual; if you
detect any inaccuracies or omissions, please inform your local Axis
office which can be found on the cover of this document. Axis
Communications AB cannot be held responsible for any technical or
typographical errors and reserves the right to make changes to the
product and manuals without prior notice. Axis Communications AB
makes no warranty of any kind with regard to the material contained
within this document, including, but not limited to, the implied
warranties of merchantability and fitness for aparticular purpose. Axis
Communications AB shall not be liable nor responsible for incidental
or consequential damages in connection with the furnishing,
performance or use of this material.
Trademark Acknowledgments
Acrobat, Adobe, AIX, DOS, Ethernet, IBM, Internet Explorer, Macintosh,
Microsoft, Netscape Navigator, UNIX and Windows are registered
trademarks of the respective holders.
Software Trademark Acknowledgments
JPEG code (libjpeg) used courtesy of the Independent JPEG Group.
LDAP code (libldap and libber) used courtesy of the University of
Michigan at Ann Arbor. Copyright © 1991 Regents of the University of
Michigan. All rights reserved. TIFF code (libtiff) used courtesy of Sam
Leffler and Silicon Graphics, Inc. Copyright © 1988-1996 Sam Leffler.
Copyright © 1991-1996 Silicon Graphics, Inc.
Support Services
Should you require any technical assistance, please contact your local
dealer. If your questions cannot be answered immediately, your dealer
will forward your queries through the appropriate channels to ensure
you a rapid response. For more information please visit the Axis web
site at www.axis.com.
User’s Guide AXIS 70/70U Rev 1.1 Part No: 19617
Date: October 2002
Copyright © Axis Communications AB, 2002

AXIS 70/70U User’s Guide Table of Contents 3
Table of Contents
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Physical Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Basic Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Installation Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Checking the Hardware Inventory. . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connecting the Scanner to the AXIS 70/70U . . . . . . . . . . . . . . . . . .10
Connecting the AXIS 70/70U to the Network . . . . . . . . . . . . . . . . . .10
Assigning an IP Address to the AXIS 70/70U . . . . . . . . . . . . . . . . . .11
Verifying the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Configuring the AXIS 70/70U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Accessing the Administration Tools . . . . . . . . . . . . . . . . . . . . . . . . .15
Specifying the Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Specifying Destinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Specifying a destination automatically. . . . . . . . . . . . . . . . . . . . . . .17
Specifying a destination manually . . . . . . . . . . . . . . . . . . . . . . . . . .17
Adding New Destinations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Specifying System Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Using the AXIS 70/70U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Sending to Destinations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Adding E-mail Destinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Using a standard PC Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Adding a new e-mail address to the list using a keyboard. . . . . . . . .22
Viewing the Scanned Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Specifying a Sender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Receive your own copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Receive notification of sent e-mail. . . . . . . . . . . . . . . . . . . . . . . . . .23
AXIS 70/70U Parameter Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Introduction AXIS 70/70U User’s Guide
4
Introduction
This document provides introductory instructions on how to set up and
manage the AXIS 70/70U Network Document Server within your networking
environment. For more information, please refer to the applicable parts of the
AXIS 70/70U/7000 User’s Manual, which is available from the Axis Web site at
http://www.axis.com or in PDF format on the AXIS Network Product CD.
Important!
AXIS Network Product CD
The AXIS Network Product CD provides an easy-to-use electronic catalog, that
includes all of the latest AXIS Software Utilities, Product Software, White
Papers, User Documentation, Technical Notes, etc. It is compatible for use
within all of the supported Axis computing environments.
The AXIS 70/70U is server independent and requires no additional software for
installation purposes. Software provided on the AXIS Network Product CD is
optional for management and installation.
You can view the contents of the AXIS Network Product CD via the Adobe
Reader interface or HTML interface. All documents presented on the CD are in
PDF format.
Note:
Axis Web site
All of the software and information provided on the AXIS Network Product
CD is also available from the Axis Web site at http://www.axis.com. From this
site you can access corporate and support information, learn more about other
Axis products, etc.
Online help is available on every page within the AXIS 70/70U web interface. This is of
particular relevance when configuring the unit and should be used as a first point of reference for
any administration queries. The help system is stored internally in the AXIS 70/70U.
If the Adobe Acrobat Reader 3.0 or higher is not installed on your system:
• Windows users should click Get Adobe Reader button from the main user interface.
• Non-Windows users should locate and run the appropriate installer from the tools/Acrobat/
folder. Refer to the readme.txt file for full path name details.

AXIS 70/70U User’s Guide Product Overview 5
Product Overview
The AXIS 70 and AXIS 70U Network Document Servers, referred to in this
document as the AXIS 70/70U, are easy solutions for instant digital document
distribution over networks. Faster, cheaper and safer than fax, traditional mail
and courier. The total cost of ownership is favorable since the distribution
relies upon the fixed IP network and not fax lines, postage or courier.
• AXIS 70 - SCSI connection
• AXIS 70U - USB connection
Note:
Supplied as a standalone unit, typically located beside your scanning device,
one AXIS 70/70U is required for each scanner.
For convenient electronic distribution of copied materials to e-mail addresses,
it is suggested that the AXIS 70/70U and the scanning device be located in the
mail or printer room - in close proximity to the workgroup or department
users.
The AXIS 70U does not support USB hubs or USB converters. The AXIS 70U will only support one
connected device at a time..
The AXIS 70U supports USB 1.1
AXIS 70/70U
E-mail
Scanner

Physical Description AXIS 70/70U User’s Guide
6
Physical Description
The Control Panel
The AXIS 70/70U Control panel has user keys (described below) and a message
display that describes the selected menu options and current status of the unit.
Note:
When sending your document, the AXIS 70/70U always uses the currently displayed destination
and scanning options, whether explicitly selected or not
Add Page Scans the material in the scanning
device. For bound material, use this
key to scan each page.
Cancel Cancels the scanning process at any
stage and clears any selections
made from the menu. Resets error
messages.
Menu Scrolls through the menu.
Select Selects multiple destinations.
Send Sends the scanned material to the
selected destination and releases
the AXIS 70/70U for other users. For
a single page/stack of paper, use
this key to scan the material and
send the image in one step.
Up/Down Scrolls and selects menu options.
• You can connect a standard PC-AT Keyboard to the AXIS 70/70U. This allows you to enter tem-
porary e-mail addresses at the scanner and easily search long e-mail listings. See also Adding
E-mail Destinations, on page 21.
• For more detailed information, please refer to the AXIS 70/70U/7000 User’sManual at the Axis
Web site http://www.axis.com or on the AXIS Network Product CD.
AXIS 70
ver: 1.00

AXIS 70/70U User’s Guide Physical Description 7
Indicators
Status Indicator
The Status indicator flashes during startup and remains lit when the AXIS
70/70U is ready for use. If the Status indicator turns off, this may indicate an
error.
Busy Indicator
The Busy indicator turns on when the AXIS 70/70U is allocated for use and
remains on during the scanning process.
Network Indicator
The tri-colored Network indicator flashes:
yellow - indicating network activity on a 10MB Ethernet network
green - indicating network activity on a 100MB Fast Ethernet network
red - indicating that the unit is not correctly connected to the network
Power Indicator
The Power indicator is normally on when power is applied. If the indicator
remains off or flashes, this indicates a problem with the AXIS 70/70U or its
power supply.
Status
Indicator Busy Indicator Network
Indicator Power Indicator

Physical Description AXIS 70/70U User’s Guide
8
Connectors
AXIS 70
AXIS 70U
SCSI Connector (AXIS 70)
A SCSI-2 connector for connection to the scanner.
USB Connector (AXIS 70U)
A USB connector for connection to the scanner.
Keyboard Connector
A mini-DIN connector for connection of a standard PC-Keyboard. Refer to the
AXIS 70/70U/7000 User’s Manual for further details.
Network Connector
The AXIS 70/70U is designed for 10 Mbps Ethernet and 100 Mbps Fast
Ethernet networks and connects to the network via a twisted pair category 5
cable (10baseT and 100baseTX). The AXIS 70/70U automatically switches
between 10 Mbps and 100 Mbps.
Power Supply
AXIS PS-H power supply (see Checking the Hardware Inventory on page 9)
Keyboard
Connector Power
Supply
Network
Connector
SCSI
Connector
Keyboard
Connector Power
Supply
Network
Connector
USB
Connector

AXIS 70/70U User’s Guide Basic Installation 9
Basic Installation
Installation Summary
The AXIS 70/70U is installed in the following stages:
• Checking the Hardware Inventory
• Connecting the AXIS 70/70U to a scanner
• Connecting the AXIS 70/70U to the network
• Assigning an IP address to the AXIS 70/70U
• Verifying the installation
Checking the Hardware Inventory
Unpack and check all the items using the following list. Contact your dealer if
anything is missing or damaged. All packing materials are recyclable.
Hardware Models Part Numbers
Network Document Servers AXIS 70 0157-001-01
AXIS 70U 0162-001-01
Power Supply AXIS PS-H Europe 18424
UK 18425
Australia 18428
USA 18480
Japan 18480
Media Title Part Numbers
CD-ROM AXIS Network Product CD 1.2 0r later
Printed Materials AXIS 70/70U User’s Guide R1.0 19617
AXIS 70/70U Instruction Label 19127
AXIS 70/70U Keyboard Instruction Label 16763
Optional Accessories Description Part Numbers
SCSI Cables (AXIS 70 only) 50-pin high-density shielded SCSI
connector (micro-D) 14260
50-pin high-density shielded SCSI
connector (Centronics) 14259
Mini Keyboard US 17588
DE 17883
UK 17884

Basic Installation AXIS 70/70U User’s Guide
10
Connecting the Scanner to the AXIS 70/70U
Caution!
AXIS 70
1. Switch off the scanning device and disconnect the AXIS 70 external power sup-
ply. The SCSI bus may become damaged if you connect or disconnect units when
power is on.
2. Connect the SCSI cable to the SCSI connector on the AXIS 70.
3. Connect the SCSI cable to the scanning device. The AXIS 70 uses a built-in SCSI
terminator. Note that the scanning device must also be terminated properly.
Refer to the documentation supplied with your scanning device.
AXIS 70U
1. Switch off the scanning device and disconnect the AXIS 70U external power
supply.
2. Connect the USB cable to the USB connector on the AXIS 70U.
3. Connect the USB cable to the scanning device.
Connecting the AXIS 70/70U to the Network
1. Connect your AXIS 70/70U to the network. The AXIS 70/70U is designed for 10
Mbps Ethernet and 100 Mbps Fast Ethernet networks and connects to the net-
work via a twisted pair category 5 cable (10baseT and 100baseTX).
2. Switch on the scanning device.
3. Connect the external power supply to the AXIS 70/70U. The network indicator
will flash during power up and self test. The following message will appear on
the display during self test (x.xx is the software version number, e.g. 1.00):
Note:
• Check that the power supply included with your AXIS 70/70U is marked with the correct
mains voltage.
The tri-colored Network indicator flashes:
• yellow - indicating network activity on a 10MB Ethernet network.
• green - indicating network activity on a 100MB Fast Ethernet network.
• red -indicating that the unit is not correctly connected to the network.

AXIS 70/70U User’s Guide Basic Installation 11
Assigning an IP Address to the AXIS 70/70U
Follow the instructions below to set the IP address from the Control Panel.
Important!
1. Power up the AXIS 70/70U and press Menu when this message appears:
2. After a few seconds this display will be shown:
3. Press Select to edit the IP address:
4. Press Menu to move through and highlight each digit, one at a time.
5. Use to increase or decrease each highlighted digit, as required.
6. Press Select to confirm the changes.
7. Press Menu to display the default router address setting:
• This section can be ignored if you are using DHCP, RARP or BOOTP, as the IP address is set auto-
matically (DHCP is the preferred method for Windows NT networks, as it automatically sets
some of the parameters as well).
• A valid and unused IP address must be acquired from your Network Administrator.
• Connecting a PC-AT keyboard directly to the mini-DIN connector on your AXIS 70/70U pro-
vides a convenient method for managing the unit, and setting the IP address during system
start up. The administrator can choose to disallow this function from the Administration
pages. Please make sure that the AXIS 70/70U power supply isdisconnected before connecting
the keyboard.
• The IP address for your product can also be set using the AXIS IP Installer (included on the
AXIS Network Product CD), or the ARP, RARP BOOTP or DHCP methods.
Please refer to the AXIS 70/70U/7000 User’s Manual for further details.

Basic Installation AXIS 70/70U User’s Guide
12
8. Press Select to edit the default router address:
9. To change the value, repeat steps 4 - 6 above.
10. Press Menu to display the subnet mask setting:
11. Press Select to edit the subnet mask:
12.To change the value, repeat steps 4 - 6 above.
13.Press Menu to display the node address. This address is not editable. The
node address should be equal the AXIS 70/70U serial number found on the
underside label of the unit.
14.Press Menu once more to display the final instructions:
15.Press Select to exit the network settings. The AXIS 70/70U then completes
the startup sequence.
16.Write the name or IP address of the AXIS 70/70U on the supplied instructions
label and attach it to the top cover.
The unit is ready for use when the Status indicator stops flashing and remains
lit.
Note:
If you make a mistake when editing the parameters, press the Cancel button to cancel the
previous operation.

AXIS 70/70U User’s Guide Basic Installation 13
Verifying the Network Settings
Access the Advanced menu from the AXIS 70/70U control panel to verify that
your chosen network settings are correct, as described below:
1. To access the Advanced menu, press and hold down Menu and Select
simultaneously.
2. Use to find the Network Settings option.
3. Press Select to enter the submenus.
4. Use to scroll through and check the parameter settings.
Verifying the Installation
Upon successful installation, the AXIS 70/70U will identify the attached
scanning device and display its name. If the connected scanning device is not
supported, an error message will be displayed.
If no destinations have previously been specified, the AXIS 70/70U displays:
If one or more destinations have already been specified, the AXIS 70/70U will
display (xxxxxx is the first Destination Name):
Note:
To verify the installation, access the AXIS 70/70U using a standard Web
browser such as Netscape Navigator or Microsoft Internet Explorer, as
described below:
1. Place a document in the scanning device.
2. Start your Web browser.
3. Enter the name or IP address of your AXIS 70/70U in the location/address field
of your Web browser.
• The Destination Name is the text that appears in the destination list on the message display.
• Destinations are sorted in alphabetical order.

Basic Installation AXIS 70/70U User’s Guide
14
Example:
The AXIS 70/70U Home Page is displayed.
4. Click admin.
5. Enter username and password.
6. Click Profiles.
7. Click on one of the profile names.
8. Click Scan. Depending on the image format specified by the profile, the web
browser will display the image in an associated image viewer, or ask you to save
the file.
http://172.16.253.80

AXIS 70/70U User’s Guide Configuring the AXIS 70/70U 15
Configuring the AXIS 70/70U
This section is targeted specifically to users responsible for the administration
of the AXIS 70/70U. Administrator(s) are granted with high-level privileges
that are denied to the ordinary user(s).
The following settings must be specified by the administrator before the
AXIS 70/70U can be used for distributing reproduced documents on your
network:
Network settings: define the parameters for TCP/IP and SMTP protocols.
Destinations: specify the e-mail address to which you wish to send your
document.
Notes:
Accessing the Administration Tools
The web-based administration tools provide a convenient method for
managing destinations, profiles, defining the network protocol settings,
establishing user privileges, authentication etc. The AXIS 70/70U
Administration pages are password protected and available to the
Administrator(s) only.
Follow the instructions below to access the Administration tools using a
standard web browser, such as Netscape Navigator or Microsoft Internet
Explorer.
1. Start your web browser.
2. Enter the name or IP address of your AXIS 70/70U in the location/address field.
Example: http://172.16.253.80
The AXIS 70/70U home page is displayed.
• If you have an active DHCP or BOOTP server on your network, most network settings will be set
automatically. However, it is strongly recommended that you verify the settings from the web
browser interface.
• When installing the AXIS 70/70U for the first time, it is recommended that the Administrator
retains default system settings, profiles and paper sizes. The settings can be optionally custom-
ized at a later date once you are familiar with the unit operation and functionality.
• Refer to applicable parts of the AXIS 70/70U/7000 User’s Manual for information on the set-
tings for profiles.
• It is possible to enable user authentication to restrict use of the AXIS 70/70U to validated users
only. For more information, please refer to the AXIS 70/70U/7000 User’s Manual at the Axis
web site http://www.axis.com or on the AXIS Network Product CD.

Configuring the AXIS 70/70U AXIS 70/70U User’s Guide
16
3. Click the Admin button to display the This AXIS 70/70U web page. Enter user-
name and password, by default set to root and pass respectively.
Specifying the Network Settings
Referring to the information services table below, use the Wizard to configure
the TCP/IP and SMTP settings. Optionally, configure the External Address
Book for the automatic retrieval and loading of e-mail addresses and/or web
(HTTP) definitions:
1. Click Network Settings.
2. Click Wizard for the AXIS 70/70U to guide you through the configuration
procedures for each of the supported network protocols. This is a convenient
way to set up your AXIS 70/70U in your network environment.
3. Click Detailed View to verify the settings.
The table below provides an overview of the supported protocol settings
describing both purpose and function:
Protocol setting Purpose and function
TCP/IP Defines the IP address, default router and subnet mask, automatic
download method (BOOTP, RARP or DHCP), domain name and DNS server.

AXIS 70/70U User’s Guide Configuring the AXIS 70/70U 17
Specifying Destinations
A destination is defined as an e-mail address created either automatically or
manually.
Specifying a destination automatically
Specify a destination automatically by referencing a list of e-mail addresses
on an LDAP server. Refer to Specifying the Network Settings (above) for
details.
E-mail destinations can also be designated as either permanent or temporary.
Notes:
Specifying a destination manually
1. Click Destinations. The table lists the currently available destinations. If you
allow users to add temporary e-mail destinations, these will appear at the top of
this table.
2. Click Make Permanent only if you want to make a temporary e-mail desti-
nation permanent. The Make Permanent button will only appear if there are
temporary destinations available.
E-mail SMTP •Defines the IP addresses or DNS names for primary and secondary
e-mail servers, connection timeout and e-mail reply address
•Enables / disables e-mail notification and copy features
•Enables the SMTP authentication method and defines whether to
retrieve the user identification from an external or internal account.
See the help files for details.
External Address Book Defines a list of e-mail addresses resident on an LDAP server. These can be
automatically retrieved and added to the AXIS 70/70U destination list.
• All destination names aredisplayed on the AXIS 70/70U message display, regardless ofwhether
they are loaded automatically or manually. However, only manually loaded e-mail destinations
are shown in the AXIS 70/70U Destinations page.
• For more information, please refer to the AXIS 70/70U/7000 User’s Manual at the Axis Web site
http://www.axis.com or on the AXIS Network Product CD.
Protocol setting Purpose and function

Configuring the AXIS 70/70U AXIS 70/70U User’s Guide
18
Notes:
Adding New Destinations
From the Admin - Destinations web page, follow the instructions below to add
new e-mail destinations:
Note:
Specifying System Settings
Follow the instructions below to set “system information”, “administrator
password”, “password protected user privileges”, “language” etc.
1. Click This AXIS 70/70U. The system settings are displayed.
2. Click Edit to change any of the system parameters. It is recommended that you
set a Server Password for protecting the Administration pages.
The table below provides an overview of the information and services
provided by each button on this page:
• Click Destination Defaults to specify the destination default settings, e.g. the default profile.
• Click E-mail Subjects to specify default e-mail subjects.
Destination Type Options / Description Instruction
E-mail With the image included
as an E-mail attachment •Click E-mail Destination New>>
•Specify the new E-mail address, Destination
name and Profile.
•To save the new destination, click Add To List
•After adding all required destinations,
click Done.
To specify the default settings, e.g. the default profile, click Destination Defaults.

AXIS 70/70U User’s Guide Configuring the AXIS 70/70U 19
Note:
Button Description
Edit General enter Server Password and confirm
Date & Time enable date and time information from a time synchronization source or
set manually
User Options allow/disallow privileges allowed to normal users, namely:
•Add temporary e-mail destinations
•Specify the sender of scanned documents
•Configure network settings from the control panel
•specify subject for e-mail destination
Authentication Enable Windows NT Server (SMB) server authentication as
authentication method.
Note: refer to the Network settings | E-mail (SMTP) tab for information
on SMTP authentication.
International •Select the supported language displayed on the AXIS 70/70U mes-
sage display (English, French, German, Italian, Spanish, Swedish, Dan-
ish or Norwegian)
•Select the keyboard layout compatible with the external keyboard
and the measurement units used for displaying defined paper sizes
(centimeters or inches)
View Settings Lists the current parameter settings in the configuration file.
Restart Server Restarts the AXIS 70/70U. Removes all previously loaded temporary
destinations and profiles from memory.
Factory Default Restores the factory default settings and restarts the AXIS 70/70U
automatically. All previously loaded destinations and profiles are erased
from memory.
If you lose the Server password, you will need to restore the factory default settings. Refer to the
AXIS 70/70U/7000 User’s Manual on how to do that. Note that all your current settings will be
lost.

Using the AXIS 70/70U AXIS 70/70U User’s Guide
20
Using the AXIS 70/70U
The services provided to normal users are determined by the administrator
when configuring the product. This section describes all services that can be
made available to a user, namely:
• Sending to destinations
• Adding temporary e-mail destinations
• Viewing the images
• Specifying a sender
Note:
Sending to Destinations
Follow the instructions below to send information to one or several e-mail
destinations - directly from the AXIS 70/70U control panel:
1. The AXIS 70/70U is ready for use when the following message is displayed:
2. Where xxxxxx is the destination name.
Note:
3. Use the scrolling keys to find your required destination in the list.
Press and hold the key to autorepeat scrolling. If you want to add a temporary
e-mail destination, refer to Adding E-mail Destinations, on page 21.
4. If you want to send the image to more than one destination, press Select
to choose each destination:
5. Repeat steps 2 and 3, until all desired destinations are selected.
Administration instructions for setting user privileges are provided in Specifying System Settings,
on page 18.
If the following message is displayed your administrator has enabled authentication and you
must enter your user name and password. For further information, please refer to the AXIS
70/70U/7000 User’s Manual at the Axis Web site http://www.axis.com or on the AXIS Network
Product CD.