Axminster Trade AT330T User manual

AT330T, AT330ST
Thicknesser
AT330TCode 501207
AT330ST Code 105070
Original Instructions
AT: 18/09/2020
BOOK VERSION: 02

1
CONTENTS
GENERAL SAFETY RULES FOR POWER TOLLS ........................................................................ 2
SAFETY INSTRUCTIONS FOR 13” PLANER.................................................................................. 4
INSTALLATION...................................................................................................................................... 5
SPECIFICARIONS ................................................................................................................................ 5
ASSEMBLY AND SETUP .................................................................................................................... 5
ADUST THE TABLE EXTENSION ROLLER .................................................................................... 6
CIRCUIT BREAKER SWITCH............................................................................................................. 6
ADJUST DEPTH OF CUT.................................................................................................................... 6
DEPTH OF CUT GAUGE..................................................................................................................... 7
THICKNESS PRE-SET GAUGE ......................................................................................................... 7
LOCK HANDLE...................................................................................................................................... 7
STOCK ROLLERS ................................................................................................................................ 8
PREPARING THE WORK.................................................................................................................... 8
AVOID DAMAGE THE BLADE............................................................................................................ 8
FEEDING THE WORK.......................................................................................................................... 8
REPLACING THE BLADES................................................................................................................. 9
REPLACEMENT CARBON BRUSH................................................................................................. 10
REPLACEMENT V-BELT................................................................................................................... 10
LUBRICATION ..................................................................................................................................... 10
TROUBLE SHOOTING....................................................................................................................... 11
EXPLODED VIEW............................................................................................................................... 13
PART LIST............................................................................................................................................ 16

2
GENERAL SAFETY RULES FOR POWER TOLLS
WARNING: Do not attempt to operate until you have read thoroughly and understand
completely all instructions, rules, etc. contained in this manual. Failure to comply
can result in accidents involving fire, electric shock, or serious personal injury.
Keep this owner manual and review frequently for continuous safe operation.
1. Know your machine. For your own safety, read the owner’s manual carefully.
Learn its application and limitations, as well as specific potential hazards pertinent to this
machine.
2. Make sure all tools are properly grounded. If the tool electrical plug has three
prongs. If should used with a three-hole electrical socket. If a three-prong to two-prong
adapter is used, the adapter lug must be properly grounded. Do not remove or otherwise
disable the third plug.
3. Keep guards in place and in working orders. If a guard must be removed for
maintenance or cleaning, make sure it is properly reattached before using the tool again.
4. Remove adjusting key and wrenches. Form habit of checking to see that keys
and adjusting wrenches are removed from the machine before turning it on.
5. Keep work area clean. Cluttered areas and workbenches increase the
likelihood of an accident.
6. Do not use in dangerous environments. Do not use power tools in damp or
wet locations, or expose them to rain. Keep work area well illuminated.
7. Keep children away. All visitors should be kept at a safe distance from work
area.
8. Make workshop childproof. With padlocks, master switches, or by removing
starter keys.
9. Do not force the machine. It will do the job better and be safer at the rate for
which it was designed.
10. Use the right tools. Do not force the machine or attachments to do a job for
which they were not designed. Contact the manufacturer or distributor if
there is any question about the tool’s suitability for a particular job.
11. Wear proper apparel. Avoid loose clothing, gloves, neckties, rings, bracelets,
or jewelry
which could be caught in moving parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
12. Always use safety glasses. Also use face or dust mask if operation is dusty.
Everyday eyeglasses only have impact resistant lenses. They are NOT safety glasses.
13. Secure work. Use clamps or a vise to hold work when practical. It is safer
than using your hand and frees both hands to operate the tool.

3
14. Do not overreach. Keep proper footing and balance at all times.
15. Maintain machine in top condition. Keep machine clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
16. Disconnect machine from power source. Before servicing and when
changing accessories, or when mounting and remounting motor.
17. Avoid accidental starting. Make sure switch is in the “off”position before
plugging in power cord.
18. Use recommended accessories. Consult the owner’s manual for
Recommended accessories.
19. Check damaged parts. Before further use of the machine, a guard or other
part that is damaged should be carefully checked to make sure that it will operate
properly and perform its intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting, and any other condition
that may affect its operation.
Guards or other parts that are damaged should be properly repaired or replaced.
20. Never leave machine running unattended. Turn power off. Do not leave the
machine until it comes to complete stop.
21. Do not use any power tools while under the effect of drugs, alcohol, or any
medication.
22. Always wear a face or dust mask if operation creates a lot of saw dust and or
wood chips. Always operate the tool in a well ventilated area and provide for proper dust
removal. Use a wood dust collection system whenever possible.
23. Provide for adequate space surrounding work area and non-glare, overhead lighting.
24. Keep the floor around the machine clean and free of scrap material, oil and grease.
25. Keep visitors a safe distance from the work area. Keep children away.
26. Make your workshop child proof with padlocks, master switches or by removing
starter keys.
27. Give your work undivided attention. Looking around, carrying on a conversation and
“horse-play” are careless acts that can result in serious injury.

The spiral cutter block has four rows of square cutters running
around its circumference.There is a blade machined to each
side of the square cutter allowing the cutter to be rotated to a
clean sharp edge if one side has been damaged or has become
blunt, see fig 14A.
The square cutter has an embossed position marker to one
of its four corners, once this mark has gone round one fall
rotatation it is time to replace the square cutter.
To rotate the cutter, loosen the Torx head screw and rotate
until the new edge is in alignment with the other cutters.
Re-tighten the Torx head screw to lock the cutter in place.
WARNING! BE VERY CAREFUL WHEN TURNING THE
CUTTERS AS THE BLADES ARE EXTREMELY SHARP.
DO NOT OVERTIGHTEN TO AVOID THE SCREW HEAD
FROM GETTING DAMAGED!
Spiral Cutter Block (AT330ST)
Fig. 14A
Position marker Torx head screw

13
EXPLODED VIEW

14

15

16
PART LIST
KEY
PART NO.
DESCRIPTIONS
Q'TY
1
170387-000
TOP COVER
1
2
340008-615
BUSHING
1
3
000802-101
ROUND HEAD HEX SCREW
M8*1.25P*16
4
4
001102-503
ROUND HEAD TAPPING SCREW
M4*1.59P*10
12
5
001102-502
ROUND HEAD TAPPING SCREW
M4*1.59P*8
4
6
250087-615
BUSHING
4
7
190021-906
TOP ROLLER
2
8
280049-905
POINTER
1
9
006001-035
FLAT WASHER
6.7*19*1.0
1
10
049103-103
TORX SCREW
M6*1.0P*20
1
11
920124-000
HAND CRANK
1
12
250098-615
SIDE HANDLE
2
13
910010-000
MOTOR ASSEMBLY
220V-240V 7.5A
1
.1
920266-000
TEMPERATURE CONTROL SWITCH
9AMP(220V-240V)
1
.2
000303-103
ROUND HD SCREW
M5*0.8P*10
2
.3
250151-615
MOTOR HOUSING
1
.4
021301-000
RELIEF BUSHING
M16-10B
1
.5
230113-905
SELF-TAPPING SCREW
4
.6
090064-000
MOTOR COVER
1
.7
030204-001
BALL BEARING
6200
1
.8
800012-000
STATOR ASSY
220-240V
1
.9
230103-905
SELF-TAPPING SCREW
2
.10
030205-001
BALL BEARING
6201
1
.11
250152-615
PARTITION
1
.12
410008-000
ROTOR ASSY
220-240V
1
.13
920235-000
SWITCH HOUSING ASSEMBLY
1
.14
430003-000
CARBON BRUSH BRACKET
2
.15
430013-000
CARBON BRUSH
220-240V
2
.16
430006-000
CARBON BRUSH COVER
2
.17
230106-905
SELF-TAPPING SCREW
2
.18
380047-901
MOTOR PULLEY
1
.19
250154-616
SWITCH COVER
1
.20
001201-501
SELT-TAPPING SCREW
M4*1.41P*12
2
.21
937153-000
MAGNETIC SWITCH W/SWITCH CORD
220-240V
1
.22
490723-000
FILTER
1
.23
453031-003
POWER CORD
1.0mm*3C*2m
1
.24
490515-000
TERMINAL "T"
2
14
021102-000
CABLE FASTENER
ACC-2.5
1

17
KEY
PART NO.
DESCRIPTIONS
Q'TY
15
001901-101
SET LOCK SCREW
M5*0.8P*5
3
16
001601-101
POUND HEAD SCREW W/FLAT WASHER
M4*0.7P*8/4*10*0.8t
10
17
920125-000
INLET ASSEMBLY
1
18
170390-904
CIPP
1
20
220164-000
CUTTERHEAD
1
21
360338-000
FIXING PIN
2
22
210165-000
KNIFE
2
23
924014-000
KNIFE LOCKING BAR
2
24
250140-615
CHAIN GUARD
1
25
PH10-45
SIDE COVER
26
290012-901
SHOULDER SCREW
1
27
280050-000
SPRING
1
28
000102-109
SOC HD CAP SCREW
M5*0.8P*40
3
29
010006-000
RETAINING RING
STW-15
4
30
150004-000
CHAIN SPROCKET
3
31
010003-000
RETAINING RING
STW-12
2
32
012003-018
KEY
5(+0/-0.03)*5(+0/-0.1)*9
1
33
360341-000
SHAFT
1
34
090059-000
GEAR BOX COVER
1
35
160022-000
BUSHING
1
36
320191-000
GEAR
44T
1
37
320192-000
GEAR
58T
1
38
160019-000
BRASS BUSHING
1
39
000103-103
SOC HD CAP SCREW
M6*1.0P*12
1
40
250143-616
KNOB
1
41
030206-001
BALL BEARING
6202
1
42
000102-102
SOC HD CAP SCREW
M5*0.8P*8
4
43
170292-901
FIXING PLATE
4
44
000103-102
SOC HD CAP SCREW
M6*1.0P*10
4
45
250144-615
CORD WRAP
2
46
000705-103
PAN HEAD SCREW
M4*0.7P*20
4
47
000303-103
ROUND HD SCREW
M5*0.8P*10
17
48
920096-000
ANTI-KICK BACK
1
49
001802-101
CAP SCREW W/SPRING WAHER
M6*1.0P*16/6.1*12.3
4
50
170396-901
BELT GUARD
1
51
090057-000
HEAD CASTING
1
52
920126-000
LEVER LOCK ASSEMBLY
1
53
010105-000
RETAINING RING
RTW-40
1
54
360340-902
ROD
4
55
012003-002
KEY
5*5*10
1

18
KEY
PART NO.
DESCRIPTIONS
Q'TY
56
280046-901
SPRING
4
57
130030-000
PAD
4
58
008004-100
HEX NUT
M5*0.8P(8B*4H)
4
59
000001-104
HEX. SCREW
M5*0.8P*16
4
60
010205-000
RETAINING RING
ETW-8
4
61
010103-000
RETAINING RING
RTW-35
1
62
011001-104
SPRING PIN
3*12
1
63
130032-000
LOCATION CAM
1
64
008006-100
HEX NUT
M8*1.25P-HEX13
1
65
000102-108
SOC HD CAP SCREW
M5*0.8P*35
1
66
920128-000
TENSION WHEELASSEMBLY
1
67
360316-000
FIXING PIN
2
68
160021-000
BUSHING
4
69
320194-000
GEAR
1
70
320190-000
GEAR
1
71
012002-002
KEY
4*4*7
2
72
090058-000
GEARBOX
1
73
320195-000
GEAR
1
74
360345-902
FIXING SHAFT
1
75
011001-103
SPRING PIN
3*10
1
76
008005-100
HEX NUT
M6*1.0P(10B*5H)
5
77
000002-102
HEX. SCREW
M6*1.0P*15
1
78
016205-000
CHAIN
#410*32P
1
79
110016-000
DEPTH GAUGE
1
80
280048-000
LOCATION SPRING
1
81
920129-000
POINTER ASSEMBLY
1
82
049103-104
TORX SCREW
M6*1.0P*12
2
85
280036-901
SPRING
2
86
250141-620
POINTER
1
87
006303-100
SPRING WASHER
6.1*12.3
1
88
000103-108
SOC HD CAP SCREW
M6*1.0P*25
1
89
280035-901
SPRING
2
90
130067-000
BUSHING
4
91
030207-001
BALL BEARING
6203
1
92
160020-000
COLLER
1
93
014302-000
POLY-V-BELT
135J-6
1
94
110009-000
CUTTERHEAD PULLEY
1
95
008016-200
HEX NUT
M16*1.5P(23B*7H)
1
96
170298-901
PLATE
4
97
340013-000
OUTFEED ROLLER
2

19
KEY
PART NO.
DESCRIPTIONS
Q'TY
98
280037-000
SPRING
2
99
360307-000
COLUMN
4
100
360343-902
LEADSCREW-LEFT
1
101
012002-003
KEY
4*4*8
4
102
270005-000
FIXING PLATE
2
103
320183-629
BEVELE GEAR
4
104
010001-000
RETAINING RING
STW-10
2
105
170392-000
PAD
1
106
000304-102
ROUND HD SCREW
M6*1.0P*10
4
107
170393-901
LEAD PLATE
2
108
270014-901
LOCATION PLATE
4
109
230238-905
SELF-TAPPING SCREW W/SPRING WASHER
1
110
360344-902
SHAFT
1
111
090061-000
BASE CASTING
1
112
200013-615
BELT GUARD SPACER
2
113
000002-111
HEX. SCREW
M6*1.0P*20
4
114
011004-103
SPRING PIN
6*25
4
115
000302-102
ROUND HD SCREW
M4*0.7P*8
12
116
170395-906
EXTEHSION BRACKET -R
2
117
170394-906
EXTENSION ROLLER ASSEMBLY
2
118
006001-026
FLAT WASHER
6.4*20*3.0t
4
119
000103-101
SOC HD CAP SCREW
4
120
250084-615
BUSHING
4
121
190022-906
EXTENSION ROLLER
2
122
360342-902
LEADSCREW-RIGHT
1
123
006502-100
TOOTH WASHER
5.3*10(BW-5)
1
124
230326-901
TORX SCREW DRIVER
T30
1
125
040201-000
WRENCH BOX
8*10
1
126
040003-000
HEX. WRENCH
3*63mm
1
127
130274-903
KNIFE SETTING GAGE
1
135
360305-901
PIN
4
136
320193-000
GEAR
1
137
001501-101
CAP SCREW W/SPRING WAHER & FLAT WASHER
M8*1.25P*20/8.2*15.4/8.5*19*2t
4
138
170391-906
EXTEHSION BRACKET -L
2
139
000303-102
ROUND HD SCREW
M5*0.8P*8
4
140
006001-027
FLAT WASHER
6.5*16*0.8t
1
141
006305-100
SPRING WASHER
8.2*15.4
1
142
920131-000
DUST HOOD ASSEMBLY
1