Axminster Woodturning D-SW Series User manual

PROJECT PEN KITS
Continues over...
WHAT’S REQUIRED
For more info and
videos scan here
Preparing a wooden or acrylic/polyester
blank for a pen mandrel.
1. Cut a blank to the length of the tube
plus approximately 2.5mm to allow for
trimming and squaring off the ends.
2. Mark the centre on the end of the blank.
3. Using the recommended drill bit, drill a
hole lengthwise through the blank.
4. Apply epoxy glue, Polyurethane glue or
gap filling cyanoacrylate (super glue) to
the tubes.
5. Insert the tube into the blank with a
twisting motion to spread the glue
evenly inside the hole.
1. Mount the bushings and blank onto a
pen mandrel according to the diagram.
2. Secure the bushings and blank onto the
mandrel.
3. Slide the tailstock with a live centre into
place against the mandrel and lock in
position. This is for support; only slight
pressure is required.
4. Using sharp tools, turn the blank down
to become the Pen Barrel with the
profile of your choice.
Bushing Set:
104369
Drill Bit Size:
3/8”
Minimum Blank Size:
19 mm x 19 mm x 88 mm
6. Centre the tube lengthwise inside the
blank.
7. Allow the adhesive to cure.
8. When cured, square the ends of the
blank. Using a barrel trimmer with a
guide matching the inner diameter
of the tube or a universal pen blank
squaring jig with a disc sander.
9. Take the excess material down flush
with the ends of the brass tube. (do
not trim beyond the length of the tube
since this may interfere with operation
of the mechanism and assembly).
Tips/Hints
•Excessive pressure may cause the drill
bit to wander and/or split the blank.
Slow the feed rate and back the drill
bit out repeatedly for chip removal.
•Roughen the brass tube slightly with
abrasive for better adhesion.
•Certain acrylic blanks are more
transparent than others, especially
lighter colors or blanks with light
colored swirls. To avoid the risk of the
brass tube showing through the pen
blank, paint the tubes white or black
before gluing them in.
•The barrel trimmer guide also cleans
any adhesive that may have gotten
inside of the tube.
5. Turn the blank very slightly oversize,
then sand and polish the ends down to
the same diameter as the bushings.
6. Using successively finer abrasives
gradually sand and polish the Pen
Barrel.
7. Finish the Pen Barrel with your
preferred choice of polish.
Tips/Hints
•Don’t be afraid to sharpen frequently
especially when turning acrylics.
D-SW Series Twist Pen Kit - Matt Gunmetal
Code: 104359
PREPARING THE BLANKS, HINTS & TIPS
TURNING THE BLANK, HINTS & TIPS

AXMINSTERTOOLS.COM
Visit the Knowledge blog ‘How To Make A Pen’ for hints, tips and videos
knowledge.axminstertools.com/pen-turning
Axminster Tools, Axminster, Devon, EX13 5PH
VIEW OUR FULL RANGE OF
PEN CASES AND DISPLAY BOXES ONLINE
1. Layout parts according to diagram A.
2. Fit the End Cap into one end of the
top of the Pen Barrel and press firmly
home.
4. Insert the Twist Mechanism into the
other end of the Pen Barrell and press
home.
5. Insert the Refill and the Spring.
6. Screw the Nib onto the threaded
section of the Twist Mechanism.
Tips/Hints
•Use a woodworking vice, one handed bar
clamp, arbor press or a dedicated pen
press.
•Press parts together slowly and steadily
•When pressing the parts together,
CHECK the parts are correctly aligned
with each other and straight. If the part
is crooked or misaligned, it will result in a
poor fit or render the pen unuseable.
•When laying out your pen barrel with
the parts, pay careful attention to keep
the pen barrels in the same orientation
as when on the mandrel. i.e. a pen barrel
may have a “top” and “bottom”, now is
the time to be certain of the orientation.
ASSEMBLY, HINTS & TIPS
DIAGRAM A