Azbil Infilex BC WY5610W0010 User manual

AB-7245
1
Specifications/Instructions
Infilex™BC
Multipurpose Controller
Control Unit
General
Infilex™BC Model WY5610W0010 is a multipurpose
controller designed to control building equipment, such as
AHU.
Infilex BC enables to control the temperature and humidity,
as well as building equipment operations.
Infilex BC manages Infilex VC and allows you to control and
monitors individual VAV units (ON/OFF, failure monitoring,
measuring, and setting) from client PC of our BMS. Infilex
VC being combined with Infilex BC performs load reset
control of supply air temperature, fan speed control,
interlocking operation of VAV units.
Infilex BC control unit is used with Infilex BC I/O control unit.
Infilex BC control unit conforms to all the applicable
standards of CE Marking (Class A).
AHU: Air handling unit
BMS: Building management system
VAV: Variable air volume
System Configuration
Infilex™ BC integrated into BMS: savic-net™ FX*
1
Notes:
*1 Fig. 1 shows an example of Infilex BC integrated into savic-net FX BMS. Ask our salesperson for applicable BMS.
*2 MIS may be used instead of SMS and DSS for your system. Note that MIS cannot be mixed with SMS or DSS in the same system.
Figure 1. System configuration example: Infilex BC integrated into savic-net FX BMS
SMS DSS Client PC
Infilex™BC
control unit
Infilex™BC
I/O control unit
BACnet
®
IP
Expansion bus
I/O modules
MIS*2
Infilex BC
BACnet
®
router
Third-party
BACnet®device
BACnet
®
MS/TP
BMS: Building Management System
DSS: Data Storage Server
MIS: Management Integration Server
SMS: System Management Server
Infilex™BC
I/O control unit I/O modules
BACnet
®
router
Infilex™VC for
BACnet®MS/TP
BACnet
®
MS/TP

AB-7245
2
Safety Instructions
Please read instructions carefully and use the product as specified in this manual. Be sure to keep this manual near by for ready
reference.
Usage Restrictions
This product is targeted for general air conditioning. Do not use this product in a situation where human life may be affected. If
this product is used in a clean room or a place where reliability or control accuracy is particularly required, please contact our
sales representative. Azbil Corporation will not bear any responsibility for the results produced by the operators.
Warnings and Cautions
WARNING Alerts users that improper handling may cause death or serious injury.
CAUTION Alerts users that improper handling may cause minor injury or material loss.
Signs
Alerts users possible hazardous conditions caused by erroneous operation or erroneous use. The symbol inside 
indicates the specific type of danger.
(For example, the sign on the left warns of the risk of electric shock.)
Notifies users that specific actions are prohibited to prevent possible danger. The symbol inside graphically
indicates the prohibited action.
(For example, the sign on the left notifies that disassembly is prohibited.)
Instructs users to carry out a specific obligatory action to prevent possible danger. The symbol inside graphically
indicates the actual action to be carried out.
(For example, the sign on the left indicates general instructions.)
WARNING
Before wiring and maintenance, be sure to turn off the power to the product.
Failure to do so might cause electric shock.
Be sure to ground the product with ground resistance of less than 100 Ω.
Improper grounding might cause electric shock or malfunction.
Detach the terminal cover only when wiring the product. Before detaching the terminal cover, be sure to turn off the
power to the product and all the connected devices. After wiring, be sure to reattach the terminal cover.
Failure to do so might cause electric shock.
Install this product in a location out of reach of unauthorized people. (e.g. Inside of the control panel)
Failure to do so might cause electric shock.
CAUTION (1/2)

Install the product in a location that satisfies the operating conditions (temperature, humidity, power, vibration, shock,
mounting direction, atmospheric condition, etc.) as listed in the specifications and use the product within the operating
ranges as listed in the specifications.
Failure to do so might cause fire or device failure.
Installation and wiring must be performed by qualified personnel in accordance with all applicable safety standards.
All wiring must comply with applicable codes and ordinances.

Separate the power supply cables from the signal cables so that noise generated in the power supply cables will not
affect the signal cables.
Failure to do so might cause communication errors.
To connect the wires to the screw terminals, use crimp terminal lugs with insulation.
Failure to do so might cause fire or device failure due to short circuit.
Firmly tighten the terminal screws.
Insufficient tightening of the terminal screws might cause fire or overheating.

AB-7245
3
CAUTION (2/2)

For wiring, strip each wire insulation as specified in this manual. If the strip length is longer than the specified, the
stripped part of the wires will be exposed, causing electric shock or short circuit between adjacent terminals. If it is
shorter, the stripped part will not contact the connector.
Make sure that no wire fiber is unbound from the conductor (stripped wire). Unbound wire fiber may cause electric
shock or short circuit between adjacent terminals.
After mounting the product on DIN rail, push up the DIN rail holder of the product to secure it on the DIN rail.
If the product is not fixed with the DIN rail holder, it might drop from the DIN rail and get damaged.
Do not disassemble the product.
Doing so might cause electric shock or device failure.
Dispose of the product as industrial waste in accordance with your local regulations.
Do not reuse all or part of this product.

AB-7245
4
Model Number
Model number Description
WY5610 Infilex BC control unit
W 100 V AC to 240 V AC power
0010 BACnet Building Controller (B-BC)
Note:
* Infilex BC control unit is always bundled with Infilex BC I/O control unit. When ordering Infilex BC (control unit and I/O control unit), order
number is required.
Order Number of Infilex BC
Order number Description
83171682 Infilex BC
-

101 One control unit and one I/O control unit
103 One control unit and three I/O control units
105 One control unit and five I/O control units
Part for Installation (Optional)
Part number Description
83104567-001 DIN rail mounting bracket
DIN: Deutsches Institut fur Normung (German Institute for Standardization)
Note:
* Infilex BC is mounted on DIN rail, and the DIN rail mounting bracket is required. Be sure to separately order the DIN rail mounting bracket.
Specifications
Item Specification
CPU 32-bit CPU
Main storage capacity 128 MB SDRAM
256 MB CompactFlash® memory
Max. data points 775 points
Host system communication BACnet® IP (Ethernet: 10BASE-T/100BASE-TX), 1 channel
Control unit - I/O control units communication Expansion bus (JIS IPEV-S cable (0.9 mm

1 pair), 4800 bps)
* JIS: Japanese Industrial Standards
Connectable lines One line connectable
Connectable I/O control units 25 units connectable
Time backup 72 hours
Rated input voltage 100 V AC to 240 V AC
Allowable voltage range 90 V AC to 264 V AC
Allowable ambient condition 5 C 40 C (in operation) / 10 %RH to 85 %RH (non-condensing) / 2000 m or lower altitude
Dimensions (mm) 100 (W) x 106 (D) x 140 (H)
Weight 1.0 kg
Materials,
color
Cover, door, case Modified PPE, gray
I/O terminal cover,
I/O terminal case
Modified PPE equivalent to Zylon® L240Z, gray
Panel Polycarbonate, smoke
Sheet Lexan® polycarbonate plate (0.5 mm thick), transparent
DIN rail holder Polyacetal, white
Print circuit board Glass epoxy laminate
Label (on the rear side of the
door)
Siliver mat (0.1 mm thick)
Identification plate (on the
side face of the body)
Yupo sheet (polypropylene synthetic paper, 0.06-0.1 mm thick)
Packing materials Container box: Paper
Air bubble sheet: Polyethylene
Air cushion: Polyolefin
Grounding condition 100 Ωor lower ground resistance
JIS: Japanese Industrial Standards
PPE: Polyphenylene ether
SDRAM: Synchronous dynamic random-access memory

AB-7245
5
CE Marking Conformity
This product must be installed in a panel cabinet. Besides, the product in the panel cabinet must be out of reach of unauthorized
people who are not well-trained for electric facilities.
This product complies with the following Electromagnetic Compatibility (EMC) and the Low Voltage Directive (LVD).
EMC: EN61326-1 Class A, Table 2 (For use in an industrial electromagnetic environment)
LVD : EN61010-1 Overvoltage category II
Pollution degree 2
Dimensions
Figure 2. Dimensions (mm)
100 106
140

AB-7245
6
Parts Identifications
DIP: Dual in-line package
Figure 3. Parts identification
Maintenance Clearance
Notes:
*1 For the Infilex BC control unit above and below the cable ducts, leave 35 mm or wider clearance between the top/bottom of Infilex BC and
the cable ducts.
*2 When the Infilex BC I/O control unit is directly assembled with the control unit, this maintenance clearance is not needed.
Figure 4. Maintenance clearance
Min. 50*1
Min. 50*1
Min.240
Min. 50*2
Min. 200
Min. 50
DIP switch for Data Setter line changeover
Data Setter connector
Direct input terminals
Expansion bus terminals
LED and 7-segment LED
Power supply terminals
Power supply switch
Battery
Not used
INT (initializing) switch
RESET switch
Ethernet port
Not used
Not used

AB-7245
7
Installation
Precautions for installation
CAUTION
Use the product under the operating conditions (temperature, humidity, power, vibration, shock, mounting direction,
atmospheric condition, etc.) as listed in the specifications.
Failure to do so might cause fire or device failure.
Installation and wiring must be performed by qualified personnel in accordance with all applicable safety standards.
●Install the product in a control panel.
●Keep the ambient temperature of the control panel at 37 °C or lower. If the ambient temperature rises over 37 °C,
temperature error will be detected.
●Mount a fan to prevent temperature rise.
●In addition to the product, install devices (a hub, power failure/return circuit, terminal block, etc.) that do not generate heat
inside the control panel.
●Provide ventilation holes and exhaust slot on the control panel.
●Leave minimum of 35 mm clearance between the top/bottom of the product and the cable ducts.
●Install the circuit breaker near the product. Position the product so that the circuit breaker operations are not disturbed.
Mounting position
Always install the product in upright position. Do not install it with its body tilted.
Figure 5. Installation position
Do not tilt.
Vertical
direction
Front view Side view
Do not tilt.

AB-7245
8
Installation procedure
CAUTION
After mounting the product on DIN rail, push up the DIN rail holder of the product to secure it on the DIN rail.
If the product is not fixed with the DIN rail holder, it might drop from the DIN rail and get damaged.
This product is mounted onto DIN rail.
1) Pull down the DIN rail holder.
Figure 6. DIN rail mount 1 (front view)
2) Hook the body of the product onto DIN rail and fix the body by pushing the DIN rail holder.
Figure 7. DIN rail mount 2 (side view)
DIN rail holder Pull down.
Push.
Hook.
DIN rail holder

AB-7245
9
Wiring
Precautions for wiring
WARNING
Before wiring, be sure to turn off the power to the product.
Failure to do so might cause electric shock.
Be sure to ground the product with ground resistance of less than 100 Ω.
Improper grounding might cause electric shock or malfunction.
Detach the terminal cover only when wiring the product. Before detaching the terminal cover, be sure to turn off the
power to the product and all the connected devices. After wiring, be sure to reattach the terminal cover.
Failure to do so might cause electric shock.
CAUTION
Installation and wiring must be performed by qualified personnel in accordance with all applicable safety standards.

Separate the power supply lines from the signal lines so that noise generated in the power supply lines will not affect
the signal lines.
Failure to do so might cause communication errors.
Firmly tighten the terminal screws.
Insufficient tightening of the terminal screws might cause overheating or fire.
●Single-point ground per building floor is recommended. Do not combine the ground lines of our control panel with another
panel such as a power control panel.
●Use recommended or specified cables.
●Leave communication wire way as far as possible from the power and other wire ways.
●Be sure to check connection of the cables to the corresponding terminals and connectors without any misconnections.
●Check that there is no disconnection or ground fault.
●To prevent short-circuit, check that connection (to the terminals/connectors) and termination (with tape) of all the wires are
completed.
Wiring to the power supply terminals
Crimp M3.5 ring terminal lugs with insulation on the wire
ends, and connect the crimped ring terminal lugs to the
power supply terminals of the product.
Wiring to the Ethernet port
Connect the cable to the Ethernet port of the product.
The Ethernet port is located on the bottom of the product.
Connect the ring terminal
lug and the jumper togethe
r
to the same terminal.
Ring terminal lugs
with insulation
M3.5 screw
terminals
Jumper
Figure 8. Power supply wiring
Ethernet port
Cable
Figure 9. Ethernet wiring

AB-7245
10
Wiring to the expansion bus terminals
Expansion bus line is connected to the screwless
push-in terminal block.
Insert each wire with the clamp release button pressed.
Connect all the wires to the screwless push-in terminal
block first, and then plug the terminal block into the
connectors on the product front surface.
Note:
* Max. 25 I/O control units are connectable to the control
unit via the expansion bus.
Expansion bus terminal numbers
Terminal number of expansion bus terminals Description
7 Line 1+ of expansion bus
8 Line 1- of expansion bus
9 Shield
Connection of Infilex BC control unit to Infilex BC I/O control unit
Up to 25 I/O control units are connectable to the control unit via the expansion bus.
Requirements and constraints of the expansion bus connection differ depending on the wiring length, termination, etc. Refer to
the following related documents for details.
- AB-7163 Specifications/Instructions: Infilex BC I/O Control Unit Model WY5611
- AB-6527 Specifications/Instructions: I/O Modules, User Terminal Module, and SAnet Interface Module for Infilex
AC, Infilex GC, Infilex GD, PARAMATRIX 4 Model RY50XX
To assemble the I/O control unit with the control unit, run the expansion bus cable as shown in the figure below.
Figure 11. Expansion bus wiring of the control unit to I/O control unit
Clamp release button
10 mm
Screwless push-in
terminal bloc
k
(accessory)
Product front surface
(Strip 10 mm of wire insulation.) Plug in.
Figure 10. Expansion bus wiring
Cable duct
Cable duct
Power supply wiring Power supply wiring
Expansion bus wiring

AB-7245
11
Wiring to the direct input terminals
Direct input wires are connected to a screwless push-in
terminal block.
Insert each wire with the clamp release button pressed.
Connect all the wires to the screwless push-in terminal
block first, and then plug the terminal block in the
connectors on the product front surface.
Direct input terminal numbers
Terminal number PIN number of the connector Description
1 1 Channel 1: Fire DI
2 2 Channel 1 common: Fire DI
3 3 Channel 2: Private generation DI
4 4 Channel 2 common: Private generation DI
5 5 Channel 3: Power feeding information DI
6 6 Channel 3 common: Power feeding information DI
DI: Digital input
Clamp release button
10 mm
Screwless push-in
terminal bloc
k
(accessory)
Product front surface
(Strip 10 mm of wire insulation.) Plug in.
Figure 12. Direct input wiring
Fire Input
Generator input
Power supply status input
TB1
1
2
3
4
5
6
Fire input, generator input:
Normal (No Fire, Without Generator)
Relay - Open
Maintain
Power supply status input:
Normal (Power is supplied)
Relay - Make
Maintain

AB-7245
Infilex and savic-net are trademarks of Azbil Corporation in Japan or in other countries.
BACnet is a registered trademark of American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE).
CompactFlash is a trademark of SanDisk Corporation registered in the United States and other countries.
Ethernet is a U.S. registered trademark of Xerox Corporation.
Lexan is a registered trademark of SABIC Innovative Plastics IP B.V.
Zylon is a registered trademark of Toyobo Co., Ltd.
Specifications are subject to change without notice.
Building Systems Company
http://www.azbil.com/
Rev. 4.0 Sep. 2015 AB-7245
12