Aztech DSL5018EN User manual

Aztech DSL5018EN
4-Port ADSL 2/2+ 150 MbpsWireless-N
Modem Router
V1.0

© COPYRIGHT 2013 ALL RIGHTS RESERVED
No part of this document may be reproduced, republished, or retransmitted in any form or by
any means whatsoever, whether electronically or mechanically, including, but not limited to,
by way of photocopying, recording, information recording, or through retrieval systems
without the express written permission. We reserve the right to revise this document at any
time without the obligation to notify any person and/or entity. All other company or product
names mentioned are used for identification purposes only and may be trademarks of their
respective owners.
LIMITATION OF LIABILITY AND DAMAGES
THE PRODUCT AND THE SOFTWARES WITHIN ARE PROVIDED "AS IS," BASIS. THE
MANUFACTURER AND MANUFACTURER’S RESELLERS (COLLECTIVELY REFERRED TO AS
“THE SELLERS”) DISCLAIM ALL WARRANTIES, EXPRESS, IMPLIED OR STATUTORY,
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTIES
ARISING FROM COURSE OF DEALING, COURSE OF PERFORMANCE, OR USAGE OF TRADE. IN
NO EVENT WILL THE SELLERS BE LIABLE FOR DAMAGES OR LOSS, INCLUDING BUT NOT
LIMITED TO DIRECT, INDIRECT, SPECIAL WILLFUL, PUNITIVE, INCIDENTAL, EXEMPLARY, OR
CONSEQUENTIAL, DAMAGES, DAMAGES FOR LOSS OF BUSINESS PROFITS, OR DAMAGES
FOR LOSS OF BUSINESS OF ANY CUSTOMER OR ANY THIRD PARTY ARISING OUT OF THE
USE OR THE INABILITY TO USE THE PRODUCT OR THE SOFTWARES, INCLUDING BUT NOT
LIMITED TO THOSE RESULTING FROM DEFECTS IN THE PRODUCT OR SOFTWARE OR
DOCUMENTATION, OR LOSS OR INACCURACY OF DATA OF ANY KIND, WHETHER BASED ON
CONTRACT, TORT OR ANY OTHER LEGAL THEORY, EVEN IF THE PARTIES HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE ENTIRE RISK AS TO THE RESULTS
AND PERFORMANCE OF THE PRODUCT OR ITS SOFTWARE IS ASSUMED BY CUSTOMER.
BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABLITY FOR
DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO THE PARTIES. IN NO EVENT WILL
THE SELLERS’ TOTAL CUMULATIVE LIABILITY OF EACH AND EVERY KIND IN RELATION TO
THE PRODUCT OR ITS SOFTWARE EXCEED THE AMOUNT PAID BY CUSTOMER FOR THE
PRODUCT.

CONTENTS
About the Device............................................................................................................ 1
Minimum System Requirements .................................................................................. 1
Package Contents.......................................................................................................... 1
Device Design ................................................................................................................ 2
Front Panel..............................................................................................................................2
Back Panel...............................................................................................................................3
Getting Started............................................................................................................... 4
Planning Your Network ...........................................................................................................5
Remove or Disable Conflicts...................................................................................................6
Setup the Device......................................................................................................................7
The Web User Interface (GUI) .................................................................................................8
Connecting to the Internet ......................................................................................................9
Basic Mode....................................................................................................................11
Basic –Home.........................................................................................................................11
Basic -Wizard ........................................................................................................................12
Basic –Quick Setup...............................................................................................................13
Advanced Mode.............................................................................................................14
Advanced Mode –Network.................................................................................................... 14
Network>Internet..................................................................................................................................14
Network>LAN........................................................................................................................................17
Network>DHCP Reservation.................................................................................................................18
Network> Ethernet Media Type ............................................................................................................18
Network> ADSL.....................................................................................................................................19
Network> SNMP....................................................................................................................................19
Network> CWMP...................................................................................................................................20
Network> IPv6RD ..................................................................................................................................20
Advanced –Wireless .............................................................................................................21
Wireless> Basic ....................................................................................................................................22
Wireless> Security ................................................................................................................................23
Wireless> MAC Address Filter ..............................................................................................................24
Advanced –Applications........................................................................................................24
Application > DDNS...............................................................................................................................25

Application> ACL...................................................................................................................................25
Application> Filter.................................................................................................................................26
Application> Routing.............................................................................................................................27
Application> NAT...................................................................................................................................28
Application> QoS ...................................................................................................................................29
Application> Port Mapping....................................................................................................................30
Application> Parental............................................................................................................................31
Application> Firewall ............................................................................................................................32
Advanced- System.................................................................................................................32
System>Information..............................................................................................................................33
System> Time Zone...............................................................................................................................33
System> UPnP ......................................................................................................................................34
System> Settings ..................................................................................................................................34
System> Firmware................................................................................................................................35
System> Password................................................................................................................................35
Advanced –Status .................................................................................................................36
Status> Statistic ....................................................................................................................................36
Status> ADSL Status .............................................................................................................................37
Status> System Log ..............................................................................................................................37
Status> Diagnostics ..............................................................................................................................38
Status> Network Tools..........................................................................................................................38
Modem Care Tips..........................................................................................................39
Safety Precautions........................................................................................................39

U s e r M a n u a l 1
About the Device
The Aztech DSL5018EN 4-Port ADSL2+ 150Mbps Wireless-N Modem Router with USB host
uses complete Ralink chipsets solution that fully complies with ADSL2/ADSL2+ standard.
The Aztech DSL5018EN supports 1T1R MIMO technology with PHY rate up to 150Mbps.
Targeted the residential and SOHO users that desires high quality triple play services, it is the
ideal solution to provide a 6 in 1 device for both Wired and Wireless connectivity via a ADSL2+
built in modem, Routing functionality for multi-user sharing, double-layer NAT/SPI firewall, 4
port 10/100 AutoMDI/MDIx Managed Switch for video application QoS, high speed
IEEE802.11b/g/n Wireless LAN Access Point and USB host for storage and print sharing.
Aztech DSL5018EN complies with Broadband Forum’s TR069 for remote management,
remote configuration and zero touch set up that allows cost saving on customer support and
logistics.
Security is provided via a double Stateful Packet Inspection and NAT based firewall. Hardware
accelerated AES/WEP/WPA/WPA2 based encryption/MAC Address Filtering for Wireless links.
Multiple session VPN Pass-through and DMZ support provide additional security support for
telecommuters as well as allow flexibility while maintaining security against malicious
hackers. Choices of Dynamic DNS server give users the flexibility of hosting a web or an FTP
server with various domain names.
Minimum System Requirements
Your computer must meet the following minimum requirements.
Any Operating System
Web Browser
Ethernet network adapter
An active DSL Internet account
Package Contents
Package contents are listed below. For any missing items, please contact your dealer
immediately. Product contents vary for different models.
Router
Ethernet cable
Telephone cable
POTS Splitter/Microfilter (optional)
12V 1.0A DC Power Adapter
Easy Start Guide

U s e r M a n u a l 2
Device Design
Front Panel
LABEL
ICON
ACTION
DESCRIPTION
1. POWER
Off
Steady green
Steady red
No power is supplied to the
device
Connected to an AC power
supply
Error on the device
2. ETHERNET LAN
Off
Steady green
Blinking green
No Ethernet connection
Connected to an Ethernet port
Transmitting/Receiving data
3. WIRELESS
Off
Steady green
Blinking green
Wireless interface disabled
Wireless Interface enabled
Transmitting/Receiving data
4. DSL
Blinking green
Steady green
Establishing or No DSL signal
DSL signal is established
5. INTERNET
Off
Steady green
Blinking green
Steady red
No connection to the Internet
Internet connection
established
Transmitting/Receiving data
PPP authentication failed

U s e r M a n u a l 3
Back Panel
LABEL
DESCRIPTION
1. 12VDC
12V 1.0A DC Input port
2. ON/OFF
Power ON/OFF button
3. ETHERNET
Connecting computers and other Ethernet devices (RJ45)
4. USB
Connecting USB storage or printer
5. DSL
Connecting the modem to an ADSL line (RJ11)
6. WPS
To setup wireless security with WPS-capable clients
7. ANTENNA
Fixed Wifi Antenna
8. RESET
Underneath the modem

U s e r M a n u a l 4
Getting Started
Setting up the device is easy. The flowchart below provides an outline of the steps needed to
complete the installation. Brief descriptions appear beside each step. Detailed instructions
are provided in the subsequent pages.
You may need to check some settings or disable
some applications before installation.
Plan your Network
Remove/Disable
Conflicts
Set up the Router
Connect to the
Internet
Web User Interface
Use Quickstart
Ready to Use
Connect the telephone cables, Ethernet cables,
and power adapter.
Use the quickstart from the Web User Interface
for your Internet connection

U s e r M a n u a l 5
Planning Your Network
Before moving ahead to setup your network, it is a good idea to draw out a network diagram to
help identify your network devices and plan out how to connect these devices. The illustration
below is an example of a network diagram.
Each port in the router can be used for different connections. For example:
Ethernet 1 –connect to a desktop
Ethernet 2 –connect to a set top box
Ethernet 3 –connect to a Smart TV
Ethernet 4 –connect to a Game console
Wireless –connect a wireless laptop to the built in wireless access point
To create a network diagram:
For wireless devices, identify the wireless devices you want to include in the
network.
For wired devices, identify which router port you want to use for each device.

U s e r M a n u a l 6
Remove or Disable Conflicts
To ensure that the router installation moves on smoothly, you need to remove or disable
conflicts that may interfere with the installation. Probable conflicts may include:
Internet sharing applications
Proxy software
Security software
TCP/IP settings
Internet properties
Temporary Internet files
Internet Sharing, Proxy, and Security Applications
Internet sharing, proxy software, and firewall applications may interfere with the router
installation. These should be removed or disabled before starting the installation.
If you have any of the following or similar applications installed on your computer, remove or
disable them according to the manufacturer’s instructions.
Internet Sharing Applications
Proxy Software
Security Software
Microsoft Internet Sharing
WinGate
Symantec
WinProxy
Zone Alarm
Configuring TCP/IP Settings
Check if your computer uses the default TCP/IP settings.
To check the TCP/IP properties:
1. Select Start > Run. This opens the Run dialog box.
2. Enter control ncpa.cpl and then click OK. This opens the Network Connections in
your computer.
3. Right-click LAN and then select Properties. This opens the Local Area Connection
Properties dialog box.
4. Select Internet Protocol (TCP/IP) and then click Properties. This opens the Internet
Protocol (TCP/IP) dialog box.
5. Select Obtain an IP address automatically.
6. Click OK to close the Internet Protocol (TCP/IP) dialog box.
7. Click OK to close the Local Area Connection Properties dialog box.

U s e r M a n u a l 7
Configuring Internet Properties
To set the Internet Properties:
1. Select Start > Run. This opens the Run dialog box.
2. Enter control inetcpl.cpl and then click OK. This opens Internet Properties.
3. Click Connections tab.
4. In the Dial-up and Virtual Private Network settings pane, select ‘Never dial a
connection’.
5. Click OK to close Internet Properties.
Removing Temporary Internet Files
Temporary Internet files are files from Web sites that are stored in your computer. Delete
these files to clean the cache and remove footprints left by the Web pages you visited.
To remove temporary Internet files:
1. Select Start > Run. This opens the Run dialog box.
2. Enter control and then click OK. This opens Control Panel.
3. Double-click Internet Options. This opens Internet Options.
4. In the Temporary Internet Files pane, click Delete Cookies.
5. Click Delete Files.
6. Click OK to close Internet Properties.
Setup the Device
When installing the router, find an area where there are enough electrical outlets for the
router, the main computer, and your other computer devices.
To setup the router:
1. Plug one end of the Ethernet cable from the router’s Ethernet port and then plug
the other end into the Ethernet port of your computer.
2. If you have another device you need to connect through wire into the router, use
another piece of Ethernet cable. Plug one end of the Ethernet cable from the
computer’s Ethernet port and then plug the other end into an available Ethernet
port in the router. (Applicable for multi-port devices)
3. Plug one end of the telephone cable from the POTS Splitter’s ADSL port and then
plug the other end into the router’s DSL port.
POTS Splitter (DSL Microfilter)
Your phone line carries both phone calls and Internet signals. When you are using
the Internet, the connection produces high-pitched tones that can affect your voice
calls when using the phone. Installing a Plain Old Telephone Service (POTS) splitter
separates your phone call signals and internet signals which eliminates the noise.

U s e r M a n u a l 8
To setup a telephone on the POTS Splitter (DSL Microfilter):
a. Locate the phone jack in your house.
b. Insert the POTS Splitter into the phone jack.
c. Plug one end of the telephone cable from the POTS Splitter’s TEL port
and then plug the other end into the telephone.
4. Connect the power adapter from the router’s 12V 1.0A DC port into the power
outlet.
5. Press the ON/OFF switch to turn on the device.
The Web User Interface (GUI)
The layout and content positioning of the device’s web user interface is mapped below.

U s e r M a n u a l 9
Connecting to the Internet
You can use the web user interface to setup your Internet connection.
Connecting using Quick Setup
1. Launch the web browser.
2. Input 192.168.1.1 on the address bar and press enter.
3. Input ‘admin’for username and ‘admin’for password. Click the Login button.
4. Click Quick Setup on the Basic menu. For steps 5, 6 and 7 refer to the Web User
Interface mapped below:

U s e r M a n u a l 10
5. Under WAN Connection
a. Select Connection Type
b. Input VPI and VCI on the required field.
(Note: Please refer to your Internet Service Provider for the information needed on
the required field).
6. Under Wireless
a. Tick WLAN Enabled box to enable the wireless interface.
b. Tick Broadcast SSID to broadcast Wireless Name.
c. SSID input the Wireless Name on the required field.
d. Tick WPA/WPA2 Enabled to enable the wireless security
e. Passphrase input the Wireless SSID on the required field.
7. Click the Apply button to save the settings.

U s e r M a n u a l 11
Basic Mode
Basic Mode displays pages with information about the device and its current configuration.
Basic –Home
This section of the web user interface displays information about of the Internet, LAN,
Wireless Connection, Local Network, Storage and Printer status.
Internet Connection. Provides details of the Internet connection.
LAN Connection. Provides details of Local Area Network connection.
Wireless Connection. Provides an overview of the Wireless connection information.
Local Network. Provides information of the local devices connected to the network.
Storage. Provides information of the storage device connected to the modem.
Printer. Provides information of the printer device connected to the modem.

U s e r M a n u a l 12
Basic -Wizard
This section of the web user interface guides user to setup their device to access the Internet
and set wireless connection.

U s e r M a n u a l 13
Basic –Quick Setup
This section of the web user interface displays allows user to configure Time and Date WAN
and Wireless connection.
WAN Connection. Allows user to set the WAN connection type.
1. Connection Type. Allows you to change the default Internet Connection type. Verify
with your Internet Service Provider your Internet Connection Type before changing
the configuration.
2. VPI/VCI. Allows you to change the default VPI/VCI set on the modem. Verify with your
internet Service Provider your VPI/VCI before changing the configuration.
Wireless. Displays the default configuration of the built in wireless access point.
1. WLAN Enabled. Allows you to enable or disable the wireless connection of the
device.
2. Broadcast SSID. Allows you to Broadcast or Hide the Wireless SSID.
3. SSID. Allows you to change the default wireless network name set on the device.
4. Security Mode. Allows you to change the default wireless security set on the device.
5. Encryption Mode. Allows you to change the wireless security set on the device.
6. Pre-Shared Key. Allows user to set the wireless password set on the device.

U s e r M a n u a l 14
Advanced Mode
The Advanced Mode page can be accessed from the Basic page by clicking on Advanced Mode.
Advanced Mode –Network
The initial page will show all the settings of your existing WAN connection configured on the
router.
Network>Internet
This page allows user to configure the default WAN settings of the modem/router.

U s e r M a n u a l 15

U s e r M a n u a l 16
To add a WAN interface:
1. Select an available Virtual Circuit from the drop-down box
2. Enter VPI/VCI settings (provided by your ISP)
3. Input QoS settings (provided by your ISP)
4. Select the IPv4/IPv6 version
5. Select the WAN Connection Type
6. For PPP enter PPP Username and Password (provided by your ISP)
7. Bridge Interface should be deactivated.
8. Connection Setting should be ‘Always on’.
9. Ensure Default Route is selected as Yes
10. Ensure Get IP Address is set to Dynamic
11. Ensure NAT is ‘Enable’.
12. For IPv6 Option check with your Internet Service Provider the settings required.
13. Click the Apply button to commit the settings
To edit an existing WAN interface:
1. Select the Virtual Circuit that you want to Edit from the drop down box
2. Make the necessary amendments
3. Click the Apply button to commit the settings