B-Link NANO SENSE User manual

I. Specifications
Instructions NANO SENSE
NANO SENSE adopts high sensivity detector, integrated circuit and SMD; It gathers automatic, convenient, safe, energy-saving,
practical functions; It utilizes human motion infrared rays as control signal sources, when one enters the detection field,
it will start the controlled load at once; It can identify day and night automatically; It is easy to install and its usage is widely.
Power Source
Detection Range
Frequency
230V~
360º
50Hz
Can identify day and night automatically; when turn to”sun”, it will work day and night; when turn it to “moon”(min.), it will
only work in the ambient light less than 10LUX. As for adjustment, please refer to testing way.
SENS adjustable: It can be adjusted according to using location: low sensivity for small room and high sensivity for large
room.
II. Function
EU Reg nº 003469376
www.blink.com.pt
EU Reg nº 003469376
www.blink.com.pt
Slide the LUX switch to SUN (like the picture below). Slide the SENS switch to maximum (below is the maximum).
Adjust the TIME switch, slide 5 switch to ON position (slide upwards).
When you switch on the power, and preheat 30 seconds later, the load is turned on, in the absence of no inductor signals,
the load should be stopped working within 5-30sec.
IV. Test
After the first is out, make it sense again after 5-10sec. The load should work. When there is no inductor signals in the
indicator lamp, the load should be stopped working within 5sec.
Slide the LUX switch to MOON position; it is in LUX, the load should be not work in the daylight. If you cover the detection
window with the opaque objects (towel, etc.), the load work, under no induction signal condition, the load should stop
working within 5-15sec.
When testing in daylight please turn LUX knob to SUN position, otherwise the sensor lamp could not
work!
TAKE NOTICE:
All responsibilities for defects or damages are hereby rejected if caused by: incorrect assembling of
the product, incorrect supply, use of lamps not suitable for this product, external agents. BLI/26.1.EN
All responsibilities for defects or damages are hereby rejected if caused by: incorrect assembling of
the product, incorrect supply, use of lamps not suitable for this product, external agents. BLI/26.1.EN
Working Temperature -20ºC~+40ºC
Ambient Light 10LUX/2000LUX (adjustable)
Working Humidity <93%RH
Time-Delay 5sec., 30sec., 1min., 3mins.
5mins., 8mins.
Installation Heigh 1.8m~2.5m
Power Consumption 0.45W (work)
0.1W (static)
Rated Load 800W (incandescent lamp)
200W (energy-saving lamp)
Detection Motion Speed 0.6~1.5m/s
Detection Distance 6m max.(24ºC)
Time-delay is added continually; when it receives the second induction signals after the first induction, it will compute
time once more on the rest of the first time-delay basics (set time).
Time-delay is adjustable: it can be set according to your desire, the minimum is 5sec., and the maximum is 8min.
Switch off the power.
Fix the bottom on the selected position with the inflated screw through the screw boles in the side of the sensor.
III. Installation
Connecting the power and the load to sensor as per the connection-wire sketch diagram.
Switch on the power and test it. Figura 1
Connection-wire diagram:

EU Reg nº 003469376
www.blink.com.pt
All responsibilities for defects or damages are hereby rejected if caused by: incorrect assembling of
the product, incorrect supply, use of lamps not suitable for this product, external agents. BLI/26.1.EN
Make sure NANO SENSE is installed by a professional electrician.
Do not install it on uneven and shaky surfaces.
V. Notes
Make sure there’s no object obstructing the field of detection.
Avoid installing it near air temperature alteration zones for example: air condition, central heating, etc.
Please don´t open the case for your safety if you find the hitch after installation.
If there are some difference between instruction and the function the product has, please give priority to product and
sorry not to inform you additionally.
The load don´t work:
VI. Problems and solutions
Check the power and the load.
Whether the indicator light is turned on after sensing? If yes, please check load.
If the indicator light does not turn on after sensing, please check if the working light corresponds to the ambient light.
Please check if the working voltage corresponds to the power source.
The sensivity is poor:
Please check if in front of the detection window there are hinder that effect to receive the signals.
Please check the ambient temperature.
Please check if the signals source is in the detection fields.
Please check the installation height.
The sensor can´t shut automatically the load:
If there are continual signals in the detection fields.
If the time delay is set to the longest.
If the power correspond to the instruction.
If the air temperature change near the sensor, air condition or central heating, etc.