Baby Jogger city mini GT User manual

Read these instructions carefully
before use and keep them for
future reference. Your child’s
safety may be affected if you do
not follow these instructions.
www.babyjogger.com
CITY MINI GT
ASSEMBLY INSTRUCTIONS

2
2
• This stroller is not suitable for running, jogging, skating or rollerblading.
• Prevent serious injury to your child by always using the safety harness.
• Parcels or accessory items, or both, placed on the unit may cause the unit to become
unstable.
• Never leave child unattended.
• Recommended weight for seat back pocket is 2 pounds and basket is 10 pounds.
Excessive weight may cause a hazardous unstable condition to exist.
• Stroller is not meant to be used for transporting children up or down stairs. Damage
resulting to stroller, will not be covered under warranty.
• Child may slip into leg openings and strangle. Never use in reclined carriage position
unless safety harness is properly fastened.
• Accessories which are not approved by the manufacturer or distributor shall not
be used.
• The passenger shall remain seated (no standing in the stroller).
• Watch out for cars – never assume that a driver can see you and your child.
• This stroller is suitable from birth to 5 years (maximum weight: 65 lbs.).
• Total weight load recommended for this stroller is 77 lbs (65 lbs in seat unit, 2 lbs in
seat back pocket, 10 lbs in basket).
• This stroller seats one passenger.
• It may be unsafe to use replacement parts other than those supplied or approved by
the manufacturer.
For the sake of your precious cargo, please
read these warnings before using your stroller.
WARNING:

1
1 Unpack stroller from box and set
wheels aside.
3 Turn stroller over to upright position.
2 Begin to unfold stroller by pulling the Auto-lock lever
while pushing the handle up and away from the lower
frame. The stroller will click into place.
4 Snap red safety strap to frame under the fold
mechanism before use.
FRAME
Warning: Ensure all locking devices are engaged
before use.

2
1 To install front wheel, lay stroller back so the handle is resting on floor.
2 Attach the front wheel by sliding the axle into the wheel end until it clicks.
Gently tug on wheel to make sure the front wheel is locked into place.
Swivel/Straight Feature
• Press the lever down to allow the front wheel assembly to swivel.
• Raise the lever up to lock the front wheel assembly in the straight position for long distance strolling.
NOTE: • When loading and unloading child, always press the lever down to lock the front wheel straight.
• Although the front wheel of your City Mini GT locks it is not intended for jogging or exercise purposes.
FRONT WHEEL
CLICK

3
1 Align wheel axle with wheel mount on stroller frame.
2 Insert the wheel axle into the wheel mount until it clicks into place.
Gently tug on wheel to make sure the rear wheel is properly attached.
REAR WHEELS
To install rear wheels:
1 Press the wheel release button while gently sliding the wheel
away from the wheel mount.
To remove the rear wheels:

4
2 To remove the canopy, stand
facing the stroller and press
the grey release button while
pulling up on the canopy
bracket. Repeat on opposite
side to remove entire canopy
from stroller.
1 To attach canopy to frame, simply
slide canopy peg into the top hole
of the universal mounting bracket,
until you hear it click into place.
The bottom hole can be used
to attach Baby Jogger acessories
to your stroller.
CANOPY

5
BRAKE
To engage parking brake: Gently pull brake lever into upright position
until it clicks into place.
To release parking brake: Pinch gray tabs and pull towards you. Push brake lever down until it is parallel with
the frame.
Warning: Engage parking device before loading and unloading passenger.

6
6
1 Unclip top of shoulder strap
from the seat and re-clip on
the pair of seat loops closest
to child’s shoulder height.
1 Pull shoulder pads down close to main harness buckle.
2Hold the plastic guide and pull the strap end to tighten
or pull the upper harness strap to loosen.
3 Fasten both shoulder strap buckles
into the crotch strap buckle. The
buckles should always be clicked
into place before use.
SAFETY HARNESS
To adjust harness height: To adjust harness length:
Warning:
Always use the
crotch strap in
combination with
the shoulder straps
and waist belt.
To buckle: To unbuckle:
4 Press both sides of the
shoulder buckles to release
them from the crotch buckle.
Warning:
Avoid serious
injury from falling
or sliding out.
Always properly
adjust and fasten
safety harness.

7
1 Pinch the clamp behind the seat, and slide it down to desired
recline. Pull seat down on both sides to match recline position
of clamp.Reverse steps to return to the upright position.
Weather Cover: If desired, pull
weather cover down and over
the seat back mesh. Secure
firmly over both sides of seat.
When not in use, roll weather
cover up and fasten with elastic
loop and barrel provided under
top of the canopy fabric.
RECLINING SEAT
To recline:

8
To remove the basket:
1 From the rear of the stroller: Unsnap the top
snaps of the basket from around the frame
tubing above the middle crossbar. Unsnap
the bottom snaps of the basket from around
the frame tubing below the middle crossbar.
2 From the front of the stroller: Unsnap lower
seat fabric to expose the bottom front
portion of frame. Unfasten basket Velcro
from around the frame tubing. Snap seat
fabric to frame once complete.
BASKET
The basket of your City Mini GT comes fully attached.