Baby Jogger City Single User manual

Important, Keep for
Future Reference
Assembly
Instructions
City Single
Amazing 360° Turns
Make For Extreme Maneuverability
Seat
Reclines
To
23°

2
• Important, keep this booklet for future reference.
• Accessories which are not approved by the manufacturer or distributor
should not be used.
• WARNING: Prevent serious injury to your child by always using the
safety harness.
• WARNING: Any load attached to the handle affects the stability of the jogger.
• WARNING: It may be dangerous to leave child unattended.
• Always use your wrist strap – these joggers can really roll, and the
wrist strap gives you control if you should slip or fall down.
• The passenger should remain seated (no standing in the jogger).
• Watch out for cars – never assume that a driver can see you and your child.
• Never use Roller Blades while using a Baby Jogger Jogger.
• Total weight load recommended for this Jogger is 75 lbs.
(combined passenger and baggage weight.)
• This Jogger seats one passenger.
• WARNING: Recommended weight for seat pocket is 2 pounds and basket
is 10 pounds. Excessive weight may cause a hazardous unstable
condition to exist.
• It may be unsafe to use replacement parts other than those supplied or
approved by the manufacturer.
For the sake of your precious cargo, please read
these warnings before using your Baby Jogger.

Frame
1
1. Unpack Jogger from box
and set wheels aside.
4. The Jogger frame will click into place. 5. Flip Jogger to upright position.
3. Push footplate of Jogger
away from handle by
pushing axle of Jogger
up and out.
2. Unfold adjustable
handle while
pushing both
buttons on the sides
of Jogger handle.

2
1 To install front wheel,
lay jogger back so handle
is resting on floor. Lock
front wheels to prevent
the forks from swiveling.
2 Insert the front wheel
into the forktips by
aligning the axle flats
with the forktip flats.
3 Tighten by turning the
wheel lever and holding
the opposite side.
4 Close the wheel lever
making sure that it is
flush with the tubing.
Be sure not to over
tighten.
Front Wheel
Front Wheel Locking Lever
Turn to the left to lock front wheel.

3
• To install, gently slide the
wheel’s rear axle into the hole
in the axle end until you hear it
click into place.
• To remove, simply push in
the spring lock while pulling
out the wheel.
Rear Wheels

4
Adjusting safety harness:
1 Loosen the shoulder straps from their plastic guides.
2 Slide the end of each strap through pair of seat loops closest to your child’s shoulder.
Safety Harness
WARNING: Avoid serious injury from falling or sliding out.
Always use safety harness!

5
3 Slide the end of the shoulder strap back into plastic guide.Please note: If you feel the straps are
too tight, you may adjust their length by sliding the plastic guides toward the top of the seat.
4 Lock both sides of the strap mechanism into the center buckle. To adjust the center strap,
move its plastic guide up or down.

6
Brake
Rear Wheel Parking Brake
• Simply push brake pedal down to engage brake and lift up to release.

7
1Simply adjust seat
straps to desired
degree of recline.
2Pull on strap when you
want to return the seat
to its upright position.
3Rear flap serves as sun
canopy when seat is in
reclined position.
Simply secure it to
Velcro on seat.
Reclining Seat
4Jogger is packaged with seat support frame and can be easily removed
or inserted into the seat back if additional support is desired.
Be sure to remove the frame from the back of the seat before washing.

8
Seat
1 Snap seat to frame. 2 Attach bottom part of seat
to footplate with the Velcro.
3 Wrap bottom straps around
frame, thread strap through
D-ring and secure.
4 Snap safety strap to frame.