Bachmann Williams FA-1 User manual

– Page 1 of 2 –
Bachmann Industries, Inc.
1400 East Erie Avenue, Philadelphia, PA 19124 USA
www.bachmanntrains.com
Customer Service Telephone [phone]
FA-1 DUMMY DIESEL LOCOMOTIVE INSTRUCTIONS
Thank you for purchasing a Williams by Bachmann® locomotive. This locomotive has been manufactured to provide
years of use and enjoyment. Please follow the simple instructions below.
Before operating, please lightly lubricate the points shown in the diagram below. Do not over-lubricate and take extra care
to avoid getting lubricants on the wheel surfaces.
1. For the axles and coupler pivot points Marked A, we recommend that you lubricate with a small amount of light
oil such as Bachmann E-Z Lube® #99984 Light Gear Oil. Do not over-lubricate.
2. For areas that require electrical flow, such as roller pick-ups Marked B, please use Bachmann E-Z Lube®
#99981 Conductive Contact Lube. Never use any Teflon® based oil on these areas because this type oil has
insulating properties.

– Page 2 of 2 – Printed In China
OPERATION
After unpacking the locomotive, make sure that the uncoupling plunger is in the correct position with the pin inserted in
the knuckle (see figure 1). Failure to do so will allow the uncoupling plunger to contact the center rail and a direct short
will occur when power is applied to the track.
Uncoupling
This dummy locomotive is equipped with an operating knuckle coupler at the pilot end. The rear end of the locomotive
has a fixed coupler, to allow close coupling with the matching powered unit. To uncouple, position the uncoupling
plunger over the center of electro-magnetic track uncoupling section and activate the magnet.
PERIODIC MAINTENANCE
Disassembly Instructions
You will have to remove the body shell for bulb replacement, or to install a power upgrade kit. The body shell is attached
with four screws on the bottom of the locomotive frame. The screws are located in each corner of the frame. When you re-
attach body shell, please be careful not to over-tighten the screws.
Lubrication
We recommend that you lubricate as directed on page 1 every 10 hours of operation.
Light Bulb Replacement
This locomotive uses a 12 volt bayonet style bulb. The standard replacement bulb number is 53.
Power Upgrade Kit
A power upgrade kit, Williams by Bachmann® #00241, is available to convert this dummy unit into a powered unit.
Please follow the installation instructions that are included with the kit.

Bachmann Industries, Inc.
1400 East Erie Ave Philadelphia PA 19124 USA
FA-1 (Dummy) Parts List Rev 08.10.08 Printed in China
1400
East
Erie
Ave
,
Philadelphia
,
PA
19124
USA
www.bachmanntrains.com
Customer Service Tele
p
hone 800-356-3910
P
art
N
um
b
e
r
D
escr
i
pt
i
on
N
um
b
er
U
se
d
FA-1 BODY & BODY PARTS
885-E003 Body Shell - complete 1
1-30100DFT Screw(Mounts Body to Frame) 4
885 M001R3E
MlF
1
885-M001R3E Metal Frame 1
293-04-01 Ornamental Horn 1
293-08-01 Headlight lens 1
885-X001R2,R3,R3 Window Glass 1 Set
309-01-01 Red Marker Lens (2 long, 2 short) 4
343-02-01 Fuel Tank 1
1-25060DPS Screw(Mounts Fuel Tank & rear ladder to Frame) 6
TRUCK PARTS
TRUCK PARTS
293-M023FR1 Flanged Wheel 8
293-M029NR5 Axle 4
1-30140DPM Truck Mounting Screw 2
293-E001 Operating Coupler Assembly 1
293-07-01B
N
on-Operating Coupler 1
885-M013R1 Spring for non-operating coupler 1
1-26060DPWM
M
ountin
g
Screw
f
or non-o
p
eratin
g
cou
p
ler 1
1 26060DPWM
Mounting
Screw
for
non operating
coupler
1
315-04-01 Pilo
t
1
1-30060DFM Pilot Mounting Screw 1
293-E002R1 Roller Pickup Assembly 1
293-01-02 Top Insulator for Roller Pickup 2
293-01-03 Bottom Insulator for Roller Pickup 2
1-26220DPM Roller Pickup Mounting Screw 2
343-05-01 Sideframe 4
1 30060DPM
Sideframe / Bolster Mounting Screw
10
1
-
30060DPM
Sid
e
f
rame
/
B
o
l
ster
M
ount
i
ng
S
crew
10
293-M007B Front Truck Ladder - left 1
293-M008B Front Truck Ladder - right 1
293-10-03BR1 Truck Mount 2
293-M013R1B Truck Bolster 2
See Diagram on opposite side for identification. Parts shown in Italics are not illustrated.
FA-1 (Dummy) Parts List Rev 08.10.08 Printed in China