Backfire Zealot S2 User manual

User Guide

RISK OF DEATH OR SERIOUS INJURY
Whenever you ride a board, you risk death or serious inju from loss of control, collision, and
falls. To ride safely, you must read and follow the instructions and warnings in the manual.
Always wear a helmat when riding. Avoid water, wet suaces, slippe / uneven suaces, steep
hills, trac, cracks, tracks, gravel, rocks, or any obstacles that could cause a loss of traction and
cause a fall. Avoid night riding, areas with poor visibility, and small spaces.
WARNING: Do not ride on side-hills or on an incline of more than 10 degress. Do not ride at speed
which you would not safely control the board. In case of wireless inteace or batte error, you
may need to rely on skating techniques like foot braking of sliding to stop.
WARNING: AVOID WATER!
Your board is not completely waterproof, you can easily go through the puddles but
don’t soak the board in the water. Water damage is not covered under the warranty.
WARNING: PINCH POINTS!
Keep ngers, hair, and clothing away from belts, motors, wheels, and all moving pas.
WARNING: RISK OF ELECTRONIC SHOCK!
Do not open or tamper with electronics housing, which also voids the warranty.
BACKFIRE
BACKFIRE-ELECTRIC SKATEBOARDS
SKATE
BOARDS
SINCE 2009
WARNING

·Abide by the laws and regulations in your state or count.
·Respect other drivers and pedestrians on the road.
·Avoid riding in busy tracs and crowded areas.
·Do not park your board in a way that blocks people or trac,
or may create a safety issue.
·Cross road at designated crosswalks or signaled intersections.
·When riding with other riders, keep a safe distance from each other
and other transpo devices.
·Identify and keep a safe distance from hazards and obstacles on the road.
·Do not ride your board on private propey unless you have obtained permission.
ALWAYS WEAR A HELMET
Find an open, at area with clean pavement for your rst ride.
Follow these tips to ensure a safe riding experience:
·Move the Throttle Wheel in small increments.
·Keep a wide stance on the board.
·Keep a low center of gravity.
·Lean forward when accelerating.
·Lean backward when braking.
PROTECT
Please stand according to the diagram
Lean backward when braking
Lean forward when accelerating

SPECIFICATION
Max. User Weight: 110KG
Model: Zealot S2
REMOTE: HALO
Batte Type: Lithium
Material：Aluminium alloy
Wireless Connection: 2.4GHz Charging Voltage: 5V
Batte Charging Time: 2 hours
Top Speed: 48kmh
Deck Material: + Fiberglass
Canadian Maple + ABS
Truck: 8inch Aluminum alloy
Wheel Size: 96mm
Batte Capacity: 8AH 403.2WH
Batte Charging Time: 3 hours
Wheel Material: PU
Board Weight: 10.5KG
Motor Type: Belt motors Batte Type: Lithium
Motor Power: 875w * 2
Gear adjustment: E / S / T
Max. Range: 48KM
Four riding modes:
Economy Mode: Top speed of 11 MPH (19 km/h);
Spo Mode: Top speed is 23 MPH (38 km/h);
Turbo Mode: Top speed 30 MPH (48 km/h);
Cruise Mode: Travel at a steady speed.
30% uphill capability:
Actual peormance depends on rider’s weight and road condition.
Board charging time 3 hours
Remote charging time 2 hours
Board net weight: 23LBS / 10.5KG
30%
MODE
length：995mm
width：296mm
height：129mm

BOARD GLOSSARY
REMOTE GLOSSARY
Bolts
Grip Tape
Board Deck
Charging Po
Power Switch
ESC
Belt Motors
8inch Rear Wheels
PU
PU
8inch Front Truck
Front Wheels
When the skateboard is in standby state, you can use the one-button
staup mode of the remote control.
The standby state will only be maintained for 3 days.
If the skateboard is not used for more than 3 days,
it will automatically shut down.
Suppos one-button switch
Quickly double-click the atmosphere lamp to switch on and o,
and freely switch the state of the atmosphere lamp
Throttle Wheel: Acceleration/
Braking/Preview/Navigation
Power Button: ON/OFF/Menu/Select
Turbo Button: Turbo Mode/Main Menu
Fingerprint Sensor
Forward/Reverse Toggle
S/E Button: Spo Mode/Eco Mode/
Previous Menu
Type-C Charging Po
S/E
Aluminum Housing Batte Capacity:
1000mAh
Display Size: 1.3 inch
Voltage: 5V Weight: 130g
2hr Charge Time Fingerprint Sensor
LCD Panel
LCD

POWER ON/OFF THE REMOTE AND BOARD
Hold the Power Button for 3 seconds to power ON/OFF the board.
When both the remote and board are in the OFF state, hold the Power Button on both the
board and remote at the same time for 3 seconds to pair.
-DIY WHEEL SETUP SHEET
*When the whole machine leaves the facto,
the default remote control has been paired with the skateboard
Auto-Pairing Select 2WD
Wheel Size
96mm
105mm Cloud wheel
120mm Cloud wheel
120mm PU wheel
2.6
2.6
2.8
3.1
7
7
7
7
Gear Ratio Pole Pairs
Select between KM and MILES using the Throttle
Wheel, and press the Power Button on the remote
to conrm your choice.
Select the drivetrain setup on your
board using the throttle wheel.
Select the wheel size of your board using
the throttle wheel.
[Between 90MM-200MM]
Select the gear ratio of your
drivetrain using the throttle wheel.
Select the number of Pole Pairs for your board's
motor conguration. [Between 2-26] Pairing and conguration complete.
Searching
4WD
Drive Mode
2WD KMMILES
Unit Selection
BELT
Motor Type
HUB
Motor Poles
7
9
86
5
Complete
Wheel Size
97
99
98
96
95
2.6
2.8
2.7
2.5
2.4
Gear Ratio

Do frequent maintainance checks, make sure all screws are tight before riding.
Clean the bearings regularly.
Turn o board and controller when not in use.
Recharge the batte in well ventilated area.
Do not charge the batte in area with might wet the board or charging units.
Do not leave the board charging unattended.
Stop using the product or charging unit if any wire is damaged.
Only use charging units supplied by us.
Do not use the board batte to power any other equipments.
STORAGE AND MAINTAINANCE
Lithium-ion batte can explode or cause a re if they are used incorrectly. Therefore, it is
recommended to read the following instructions ve carefully:
Safety Warning: If there was potential risk of water damage to the batte before, please disconnect
the batte from the board immediately and stop charging it or use it! Keep the batte in a d , and
re resistant place to avoid potential re risk. Please do not ship a damaged batte! A Li-ion batte
store and release its electrical energy through electrochemical reactions. When electrical energy is
drawn/discharged from the batte, lithium ions move from one electrode to the other.
The electrodes are submerged in a liquid called an electrolyte, which allows for the movement of ions
and consists of lithium salt and organic solvents. It is these organic solvents which are the leading re
hazard in Li-ion batteries. Fuhermore, the positively charged electrode (cathode) in the batte
contains oxygen, which may be released if the batte is subjected to specic stresses, e.g., internal
sho, excessive heat, and more. This means that the Li-ion batteries have all the elements needed
to self-sustain a re.
Tip: The batte will enter the hibernation state after the skateboard has been standing for 7 days.
If it cannot be turned on after receiving the skateboard, please charge and activate it rst.
-Each time before riding the board, carefully check the batte pack and especially the
protective seal. Make it is undamaged and intact. If in doubt, take the batte to a
chemical waste disposal facility.
-Never drop the board.
-Store the board with batte inside in a d place.
-Never expose the batte to tempreture above 100 celsius degrees.
-Only use ocal board charger for charging board batte.
-Never leave the board unattended when charging.
-Never make the board work when charging.
-If you are not plannig to use the board for about 2 months or longer, Please charge to 50%-60% and
charge it once a month. A lithium-ion batte that has been left empty for too long no
longer be charged.
-Charge fully the batte before rst time use. This gives it better long-term peormance.
BATTERY SAFETY

LIMITED WARRANTY:
We oer 6 months(180days) warranty on pas from the date when you receive the board.
This warranty excludes damage resulting from abuse, accident, modications, unauthorized
repairs, neglect, abuse, water damage, or other causes that are not defects in materials and
workmanship.
This warranty excludes normal depletion of consumable pas (grip tape, wheels & bearings)
unless due to a defect in materials or workmanship.
This warranty excludes gifts.
FOR ALL RETURN and WARRANTY SHIPPING:
Please keep your shipping box. The warranty does not include damage from shipping in
insucient packaging.
If a defect arises during the Warranty Period, Company will , at is options :
1) Send the new pas to replace the defect pas.
2) Exchange the aected Products with functionally equivalent Products that are new or
formed from new and/or previously used pas that are equivalent to new in peormance
and reliability.
WARRANTY
CONTACT US
Ocial Website: https://www.backreboards.com/
TIKTOK: @backreboards
Facebook Instagram You Tube User Guide