Backfire Zealot S2 User manual

User Guide

RISK OF DEATH OR SERIOUS INJURY
Whenever you ride a board, you risk death or serious inju from loss of control, collision, and
falls. To ride safely, you must read and follow the instructions and warnings in the manual.
Always wear a helmet when riding. Avoid water, wet suaces, slippe / uneven suaces, steep
hills, trac, cracks, tracks, gravel, rocks, or any obstacles that could cause a loss of traction and
cause a fall. Avoid night riding, areas with poor visibility, and conned spaces.
WARNING: Do not ride diagonally on hills or on an incline of more than 10 degress. Do not ride at speed
which you would not safely control the board. In case of wireless inteerence or batte error, you
may need to rely on skating techniques like foot braking or sliding to stop.
WARNING: AVOID WATER!
Your board is not completely waterproof, you can easily go through the puddles but
don’t soak the board in the water. Water damage is not covered under the warranty.
WARNING: PINCH POINTS!
Keep ngers, hair, and clothing away from belts, motors, wheels, and all moving pas.
WARNING: RISK OF ELECTRONIC SHOCK!
Do not open or tamper with electronics housing, which also voids the warranty.
BACKFIRE
BACKFIRE-ELECTRIC SKATEBOARDS
SKATE
BOARDS
SINCE 2009
WARNING

·Abide by the laws and regulations in your state or count.
·Respect other drivers and pedestrians on the road.
·Avoid riding in busy tracs and crowded areas.
·Do not park your board in a way that blocks people or trac,
or may create a safety issue.
·Cross roads at designated crosswalks or signaled intersections.
·When riding with other riders, keep a safe distance from each other
and other transpo devices.
·Identify and keep a safe distance from hazards and obstacles on the road.
·Do not ride your board on private propey unless you have obtained permission.
ALWAYS WEAR A HELMET
Find an open, at area with clean pavement for your rst ride.
Follow these tips to ensure a safe riding experience:
·Move the Throttle Wheel in small increments.
·Keep a wide stance on the board.
·Keep a low center of gravity.
·Lean forward when accelerating.
·Lean backward when braking.
PERSONAL PROTECTION
Please stand according to the diagram
Lean back when braking to
prevent being thrown forward by
the sudden deceleration.
Lean forward when accelerating to
prevent falling backwards
when the torque kicks in.

SPECIFICATIONS
Max. User Weight: 110KG
Model: Zealot S2
REMOTE: HALO
Batte Type: Lithium
Material：Aluminium alloy
Wireless Connection: 2.4GHz Charging Voltage: 5V
Batte Charging Time: 2 hours
Top Speed: 48kmh
Deck Material: + Fiberglass
Canadian Maple + ABS
Truck: 8 inch Aluminum alloy
Wheel Size: 96mm
Batte Capacity: 8AH 403.2WH
Batte Charging Time: 3 hours
Wheel Material: PU
Board Weight: 10.5KG
Motor Type: BLDC Outrunners Batte Type: Lithium
Motor Power: 875w * 2
Riding Modes: Eco / Spo / Turbo
Max. Range: 48KM
Four riding modes:
Economy Mode: Top speed of 11 MPH (19 km/h);
Spo Mode: Top speed is 23 MPH (38 km/h);
Turbo Mode: Top speed 30 MPH (48 km/h);
Cruise Mode: Travel at a steady speed.
30% uphill capability:
Actual peormance depends on rider’s weight and road conditions.
Board charging time 3 hours
Remote charging time 2 hours
Board net weight: 23LBS / 10.5KG
30%
MODE
length：995mm
width：296mm
height：129mm

BOARD GLOSSARY
REMOTE GLOSSARY
Bolts
Grip Tape
Board Deck
Charging Po
Power Switch
ESC
Belt Motors
8 inch Rear Truck
Bushings
Bushings
8 inch Front Truck
Front Wheels
When the skateboard is in standby mode, you can use the
one-button staup feature on the remote control.
Standby mode will automatically shutdown
when the board is not activated for 3 days.
One-button sta
Double-click the power button to activate the board
lighting on or o, and, to switch between lighting modes.
Throttle Wheel: Acceleration/
Braking/Preview/Navigation
Power Button: ON/OFF/Menu/Select
Turbo Button: Turbo Mode/Main Menu
Fingerprint Sensor
Forward/Reverse Toggle
S/E Button: Spo Mode/Eco Mode/
Previous Menu
Type-C Charging Po
S/E
Aluminum Housing Batte Capacity:
1000mAh
Display Size: 1.3 inch
Voltage: 5V Weight: 130g
2hr Charge Time Fingerprint Sensor
OLED display
OLED

PAIRING THE REMOTE TO THE BOARD
Hold the Power Button for 3 seconds to power ON/OFF the board.
When both the remote and board are in the OFF state, hold the Power Button on both the
board and remote at the same time for 3 seconds to pair.
DIY WHEEL SETUP SHEET
*The remote control and the skateboard are facto paired.
This step should not be required unless advised by technical suppo sta.
Auto-Pairing Select 2WD
Wheel Size
96mm
105mm Cloud wheel
120mm Cloud wheel
120mm PU wheel
2.6
2.6
2.8
3.1
7
7
7
7
Gear Ratio Pole Pairs
Select between KM and MILES using
the Throttle Wheel, and press the
Power Button on the remote
to conrm your choice.
Select the drivetrain setup on your
board using the throttle wheel.
Select the wheel size of your board using
the throttle wheel.
[Between 90MM-200MM]
Select the gear ratio of your
drivetrain using the throttle wheel.
Select the number of Pole Pairs for your board's
motor conguration. [Between 2-26] Pairing and conguration complete.
Searching
4WD
Drive Mode
2WD KMMILES
Unit Selection
BELT
Motor Type
HUB
Motor Poles
7
9
86
5
Complete
Wheel Size
97
99
98
96
95
2.6
2.8
2.7
2.5
2.4
Gear Ratio

Do frequent maintainance checks, make sure all nuts and bolts are tight before riding.
Clean the skateboard regularly.
Turn o board and controller when not in use.
Recharge the batte in well ventilated area.
Do not charge the batte in area with might wet the board or charging units.
Do not charge the skateboard unattended.
Stop using the product or charging unit if any wire is damaged.
Only use appropriate chargers provided by Backre.
Do not use the board batte to power any other equipments.
STORAGE AND MAINTAINANCE
BATTERY SAFETY
Lithium batteries can explode or cause a re if they are used incorrectly. Therefore, it is
recommended to read the following instructions ve carefully:
Safety Warning:
·If you rode on wet ground with a risk of water entering your batte, please remove and check your batte.
·If there is any evidence of moisture, including water stains, disconnect the batte from your board immediately.
Do not charge or use it!
·Keep the batte in a d and re resistant place to avoid potential re risk (such as a sealed bucket outdoors).
·Do not keep a potentially water damaged batte indoors.
·Do not ship a potentially water damaged batte for seice.
Contact Backre for next steps:
1.In the USA: [email protected]
2.Global: [email protected]
·Moisture inside a batte pack can cause corrosion and sho circuits in electronics such as the BMS,
lighting or USB boards. This may occur in days or weeks after water ingress.
·The lithium batteries in your pack contain lithium cobalt oxide and organic solvents.These components can
self-sustain a re when a batte is subjected to sho circuits, excessive heat or other stresses.
·Each time before riding the board, carefully check the batte pack and especially the protective seal.
Make it is undamaged and intact. If in doubt, take the batte to a chemical waste disposal facility.
·Never drop the board.
·Store the board with batte inside in a d place.
·Never expose the batte to tempreture above 100 celsius degrees.
·Only use ocal board charger for charging board batte.
·Never leave the board unattended when charging.
·Never make the board work when charging.
·If you are not planning to use the board for about 2 months or longer, Please charge to 50%-60% and
check it once a month. A lithium-ion batte that has been left empty for too long no
longer be charged.
·Fully charge the batte before its rst use to maximize long term batte peormance.
Tip: The batte will enter the hibernation state after the skateboard has been inactive for 7 days.
If it cannot be turned on after receiving the skateboard, please charge and activate it rst.

WARRANTY
CONTACT US
Ocial Website: https://www.backreboards.com/
TIKTOK: @backreboards
Facebook Instagram You Tube User Guide
LIMITED WARRANTY:
We oer 6 months(180days) warranty on pas from the date when you receive the board.
This warranty excludes damage resulting from abuse, accident, modications, unauthorized
repairs, neglect, abuse, water damage, or other causes that are not defects in materials and
workmanship.
This warranty excludes normal depletion of consumable pas (grip tape, wheels & bearings)
unless due to a defect in materials or workmanship.
This warranty excludes gifts.
FOR ALL RETURN and WARRANTY SHIPPING:
Please keep your shipping box. The warranty does not include damage from shipping in
insucient packaging.
If a defect arises during the Warranty Period, Backre will, at its discretion:
1) Send the new pas to replace the defective pas.
2) Exchange the aected Products with functionally equivalent Products that are new or
formed from new and/or previously used pas that are equivalent to new in peormance
and reliability.