Backyard Creations 272-8012 User manual

BLUE HANGING LOUNGER
272-8012
Instruction Manual

Assembly Instructions for Hanging Lounger, SKU 272-8012
Thank you for purchasing the Hanging Lounger. We hope it provides years of enjoyment. Please read and follow the assembly and safety
instructions for proper assembly and safe use of this product. If you are missing parts or if there are damaged parts, please call our customer
service department at 800-295-6758 before returning to the retailer, you can also email at [e-mail]
Part A
Part B
Part C
Part D
Parts E (x2)
Part F
Parts G (x2)
Part I
Parts J (x2)
Part K
One person should be able to assemble this product, but for easier assembly a second person is advised.
Part B
Part C
Part H
Part L
Parts M (x6)
Part N Part O
Part P
Part Q

HARDWARE
Hardware and
assembly tools are
located within the
Hardware bag.
Keep bag for
hardware storage
when not in use.
Parts R: One 3 ½” 16mm double threaded bolt with two 16mm washers and 2 acorn nuts.
Parts S : Two 2 ¾” x 13mm bolts with two 13 mm lock nuts and four 13mm washers.
Parts T : One 3 ¾” x 13mm bolt with one 13 mm lock nut and two 13 mm washers.
Parts U: Six plastic bolt caps
Part V: Threaded connecting link.
Part W: Closed S-hook.
Parts X: Four 1 3/8” x 13mm Hex head bolts.
Parts Y: Two ¾” Hex head bolts.
Part Z: Hex Wrench
Parts AA: Two Open ended wrenches.
Parts R
Parts S
Part T
Part U (X 6)
Part V Part W
Part Z
Part X (X 4) Part Y (X2)
Part AA (X2)

Step 1: Locate Part A and Part B. Connect Part B to Part A by
inserting end of Part B onto swedge end of Part A aligning holes as
shown in (Diagram 1). Place a 13mm washer onto Part S (2 ¾”
Bolt) and insert through both Part A & B (Box 1), Place a second 13
mm washer onto bolt and then a 13 mm lock nut (Box 2). Tighten
with the open ended wrenches (Part AA)
Box 1 Box 2 Box 3
Part APart B
S
T
E
P
1
Step 2: Locate Part D. Connect to Part B by placing Part B between the
metal flanges of Part D, and align the holes of the flanges with the hole
about halfway along Part B as shown in (Diagram 2). Place a 16 mm
washer onto Part R (3 ½” double threaded bolt) and insert through metal
flange of Part D through part B, and the second metal flange of Part D.
Place another 16 mm washer on exposed end of bolt, and then an acorn
nut. (Box 4) Tighten with the two open ended wrenches. (Part AA) (DO
NOT TRY TO OVERTIGHTEN –THE CONNECTION OF LEG TO UPRIGHT AT
THE FLANGE SHOULD BE ALLOWED TO PIVOT)
Diagram 1
Box 4
S
T
E
P
2
Diagram 2
S
T
E
P
3
Step 3: Place bottom end of Part C over the swedge end of Part B as
shown in Box 5. Align holes of Part B and C and insert Part S (2 ¾” bolt
with 13 mm washer) through hole until bolt shows through opposite
side of Part C as shown in Box 6. Place second 13 mm washer onto end
of bolt then the 13 mm lock nut. Tighten securely using the open
ended wrenches (Parts AA) as in Box 7.
Box 5
Part C
Part B
Box 6 Box 7
Note: The connection of Part D
with B will still be loose after
tightening acorn nuts allowing
Part D (the leg) to swivel slightly.

S
T
E
P
4
S
T
E
P
5
S
T
E
P
6
Step 4: Find Parts E. Identify the ends with the crimp over the hole as
shown in photo. Hold both Parts E with crimps facing each other and
proceed to Step 7.
Step 5: Locate Parts T (3 ¾” Bolt with 13mm washer) and insert through one of Parts E. Place Part W (Closed S-Hook) onto
the bolt Part T as shown in Box 8. Place the second and opposite Part E onto the bolt Part T as shown in Box 9. Place 13 mm
washer and 13mm lock nut onto end of Part T and tighten using open ended wrenches (Part AA) as shown in Box 10.
Box 8 Box 9 Box 10
Step 6: Locate Parts G. Place swedge end closest to bend of each Part G, and insert into both open ends of Part E as
shown in Box 11. Push down on lock-pin on each Part G as shown in Box 12, and slide Part G onto Part E until lock-pin is
fully engaged into lock-pin hole of Parts E as shown in Box 13.
Part E Part G
Bend
Box 11 Box 12 Box 13

S
T
E
P
7
S
T
E
P
8
S
T
E
P
9
Step 7: Locate Part F. Insert ends of Part F onto swedge ends of both Parts G as shown in Box 14, by pushing down lock-
pins as in Box 15 until pins are fully engaged in lock holes as shown in Box 16.
Part G Part F
Box 14 Box 15 Box16
Step 8: Locate padded arms Parts J. Attach each Part J to Part E by inserting the 1 3/8” hex bolts Part X through the holes
in Part J to the threaded holes located on the outside of parts E as shown in Box 17 & 18. Tighten each of the four bolts
securely using the hex wrench (Part Z) as shown in Box 19.
Box 17 Box 18 Box 19
Step 9: Locate Part I. Attach Part I to back of Part E using the two ¾”
hex head bolts (Parts Y) into the threaded holes on Part E as shown in
Box 20. Tighten securely using the hex wrench (Part Z).
Box 20

S
T
E
P
S
T
E
P
S
T
E
P
10
Step 10: Locate Part H and place inside seat frame as shown in Box 21. Next, locate black rope (Part K) and attach Part H to
seat frame by first threading rope through the middle grommet of Part H and pulling half of the rope through the grommet.
Lace Part H with rope over frame and through each grommet working from base on each side until the two rope ends meet at
top brace (Part I) as shown in Box 22. Tie the two ends securely around Part I as shown in Box 23. (Adjustments may need to
be made when lacing so Part H is centered in seat frame)
Start Here
Box 21 Box 22 Box 23
Step 11: Locate the Threaded Connecting Link (Part V). Place it through the eye hole of
the eyebolt at the top of the assembled stand as shown in Box 24. Next, lift the
assembled chair frame and hook the Closed S-hook on the top of the chair assembly
through the threaded connecting link as in Box 24. Turn the threaded bolt on the
connecting link so that the link is secured.
Box 24
11
Step 12: Locate Part P (chair cushion) and place over the black seat mesh (Part
H). Secure Part P to chair frame by tying the tie straps located around Part P to
the chair frame as shown in photo Box 25.
12 Box 25

S
T
E
P
13
S
T
E
P
14
S
T
E
P
15
Step 13: Locate the sunshade stem Part L, and the 6 sunshade splines Parts M. Slide each spline Part M into the ends of
the sunshade stem branches on Part L as shown in Box 26. Locate the sunshade canopy Part Q, and place it on the
ground so that the small pockets at each point of the canopy are facing up. Place the sunshade stem with inserted
splines on top of the canopy as in Box 27. Insert the ends of each spline into the small sewn pocket at each corner of the
canopy as shown in Box 28. Repeat with each spline until sunshade canopy is stretched onto each spline and the
sunshade is complete.
Box 26
Step 14: Unscrew the hand knob from the sunshade stem (Part
L). Insert the bottom of the sunshade stem into the sunshade
holder located on the top of the assembled frame as shown in
Box 29, and push down until the hole in the holder and in the
stem match up. Secure the sunshade to the frame by screwing
the hand knob into the aligned holes as shown in Box 30.
Box 29 Box 30
Step 15: This hanging lounger has two convenience accessories.
Part N is a removable hanging convenience pouch that can be
hung from the chair frame by looping the straps over the chair
frame and securing with the Velcro strap ends as in Box 31. Part
O is a drink holder. Simply loop the drink holder strap over the
chair armrest, and back through the strap so that it hangs from
the armrest as in Box 32.
Box 27 Box 28
Box 31 Box 32

S
T
E
P
16
Step 16: Place the plastic protective caps (Part U) over the heads and the nuts on
the chair frame as shown in photo.
CONGRATULATIONS! Your Hanging Lounger is now complete.
•Please always follow the safety instruction and use common sense when using the Hanging
Lounger.
•The Hanging Lounger is intended for a single user at one time and has a weight capacity of 270
lbs. NEVER EXCEED THE WEIGHT CAPACITY.
•Care should always be taken when using your Hanging Lounger but especially when using the
lounger for the first time.
•The suspended seat of the Hanging Lounger allows it to move freely, so be very cautious when
getting into and out of the Hanging Lounger.
•Never allow small children to use the Hanging Lounger unattended.
•Always inspect the Hanging Lounger before each use to assure everything is properly attached
and secure for use.
•Always use the Hanging Lounger on a level surface.
FOR YOUR SAFETY
•For spots on the pad, gently wash spotted area with a mild soap and water solution.
•The Hanging Lounger has a powder coated outdoor finish on the metal parts. However, over time
and use, scratches may develop on the metal surfaces. To avoid excessive rust, wipe these areas
of moisture.
•Before storing the Hanging Lounger, wipe thoroughly to wipe off moisture and dirt.
•Store Hanging Lounger in a dry location.
Care