Backyard Creations 273-0095 User manual

Made in China
Adirondack Chair
SKU # 273-0095 & 273-0104 & 273-0105 & 273-0106 & 273-0107
Questions or Missing Parts Please call
1 - 888 - 243 -9985 between 8:30 am to 5:00 pm EST
Or email: [e-mail]

2
Table of Contents
Safety Information
DANGER: Please keep children out of the assembly area
during assembly.
WARNING: Do not stand on the chairs. Do not sit on the
CAUTION: Use the
Warranty
armrests.
Table of Contents........................................................2
Safety Information.......................................................2
Warranty...................................................................... 2
1 Year Frame
Limited Warranty.................................................. 2
Pre-Assembly ............................................................3
Planning Assembly ................................................................3
Tools Required ....................................................................... 3
Hardware Included.................................................................. 3
Package Contents .................................................................. 4
Assembly ....................................................................5
................................................................ 2
What Is Covered
What Is Not Covered ................................................................ 2..
.... ..
................................................................ 2
Care Instructions
ONE YEAR LIMITED WARRANTY
WHAT IS COVERED
Adirondack Chairs are warranted to the original purchase to be free from defects in material or workmanship for a period of one year from
ts resulting from
misuse, abuse or customer negligence will void this warranty.
ver defects
normaly use
of the product. If the product is defective within the term of this warranty, Merry Products, Inc. will repair or replace defective parts at no cost
to the purchaser. Shipping charges are not covered and are resposibility of the purchaser.
The adirondack chair should be stationed on a level surface and kept away from extreme heat and strong oxidizing agents. Never use
petroleum or oil based products such as solvents or harsh cleaners to clean the material.
To clean material wipe the surface with a damp cloth or simply spraying with a garden hose should be adequate. If needed
mild soap or dish detergent can be used to help remove caked-on dirt.Automotive plastic car care products can be used as well. Minor
scratches can be buffed out with steel wool. Be sure and sand the surface in the direction of the grain, then wipe clean with the automotive
plastic car care product/ conditioner.
You may contact our customer service department with any questions by phone at 1-888-243-9985 or email us at [email protected]
Care Instructions
....
WHAT IS NOT COVERED

3
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part Description Quantity
AA Screw (3.5x40) 6
BB Bolt (M6x60) 2
CC 2
DD 6
Pre-Assembly
EE 4
Phillips screwdriver
TOOLS REQUIRED (not included)
Bolt (M6x70)
Bolt (M6x60)
Bolt (M6x50)
EE

4
Pre-Assembly(continued)
PACKAGE CONTENTS
Part Description Quantity
A 1
B
Back
1
C 1
D 1
Left armrest
Seat
A
B
C
D
Right armrest
F
G
H
Part Description Quantity
F 2
G
Front Legs
1
H 1
Rear Seat Slat
Front Leg Cross Beam
E 2
Vertical Back Support
E
*Note: DO NOT TIGHTEN ANY BOLTS
BEFORE THE UNIT PUT TOGETHER.

5
Assembly
1 Attaching the rear seat slat 2 Attaching the front legs
□Attach the front legs (F) onto the seat (B) with Bolts (DD).
Attach Vertical Back Support (E) onto the Seat with Bolts (EE)
using Pillips screwdriver.
□Attach the rear seat slat (H) to the seat (B) with screws (AA),
using a Phillips screwdriver.
DD
**Pre-drill mark
facing front
3 Attaching the cross board
□Attach the Cross Beam (G) to the front legs (F) with
screws (AA), using the Phillips screwdriver.
4 Attaching the Hinge
□Attach the Back (A) to the Seat (B) with Bolts (BB).
Attach the Armrest (C & D) to the Front Legs with Bolt (DD).
Attach th Armrest to the Vertical Back Support (E) with Bolt (CC).
AA
AA
H
B
AA
EE
DD
EE
E
E
F
F
G
D
C
BB
DD
CC
CC
Note: DO NOT TIGHTEN ANY BOLTS
BEFORE THE UNIT PUT TOGETHER.