Balluff BTL7-V50T-M P-C003 Series User manual

BTL7-V50T-M____-P-C003
User’s Guide
english

www.balluff.com

www.balluff.com 3english
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing
1 Notes to the user 4
1.1 Validity 4
1.2 Symbols and conventions 4
1.3 Scope of delivery 4
1.4 Approvals and markings 4
2 Safety 5
2.1 Intended use 5
2.2 General safety notes for the position measuring system 5
2.3 Explanation of the warnings 5
2.4 Disposal 5
3 Construction and function 6
3.1 Construction 6
3.2 Function 6
3.3 LED display 7
3.3.1 LED 1: BTL status 7
3.3.2 LED2: PROFINET status (dual LED) 7
3.3.3 LED3/LED4: Link/Activity 7
4 Installation and connection 8
4.1 Installing the transducer 8
4.2 Captive magnets 8
4.3 Floating magnets 9
4.4 Electrical connection 10
4.4.1 Connector BTL7-...-C003 10
4.5 Shielding and cable routing 10
5 Startup 11
5.1 Starting up the system 11
5.2 Operating notes 11
6 Technical data 12
6.1 Accuracy 12
6.2 Ambient conditions 12
6.3 Supply voltage (external) 12
6.4 Output 12
6.5 Dimensions, weights 12
6.6 Maximum sampling rate fmax 12
7 Accessories 13
7.1 Captive magnets 13
7.2 BTL2-GS10-_ _ _ _-A joint rod 13
7.3 Floating magnets 14
7.4 Connector 15
7.4.1 Power cable, preassembled with straight M8 plug 15
7.4.2 Power cable, preassembled with angled M8 plug 15
7.4.3 Data cable, preassembled with M12 plug 15
7.4.4 Data cable, preassembled with RJ45 plug 15
7.4.5 Straight data plug, freely configurable 16
7.4.6 Angled data plug, freely configurable 16
8 Type code breakdown 17
9 Appendix 18
9.1 Converting units of length 18
9.2 Part label 18

4english
1.1 Validity
This guide describes the construction, function and setup
options for the BTL7 Micropulse Transducer with
PROFINET interface. It applies to types
BTL7-V50T-M____-P-C003 (see Type code breakdown
on page17).
The guide is intended for qualified technical personnel.
Read this guide before installing and operating the
transducer.
1.2 Symbols and conventions
Individual instructions are indicated by a preceding
triangle.
►Instruction 1
Action sequences are numbered consecutively:
1. Instruction 1
2. Instruction 2
Note, tip
This symbol indicates general notes.
1.3 Scope of delivery
– BTL7 transducer
– Mounting clamps with insulating sleeves and screws
– Condensed guide
The magnets are available in various models
and must be ordered separately.
1.4 Approvals and markings
UL approval
File no.
E227256
Certified in accordance with
Conformance ClassA, B and C.
The CE Mark verifies that our products
meet the requirements of EU Directive
2004/108/EC (EMC Directive).
The transducer meets the requirements of the following
generic standards:
– EN61000-6-1 (noise immunity)
– EN61000-6-2 (noise immunity)
– EN61000-6-3 (emission)
– EN61000-6-4 (emission)
and the following product standard:
– EN61326-2-3
Emission tests:
– RF emission
EN55016-2-3 (industrial and residential areas)
Noise immunity tests:
– Static electricity (ESD)
EN 61000-4-2 Severity level3
– Electromagnetic fields (RFI)
EN 61000-4-3 Severity level3
– Electrical fast transients (burst)
EN 61000-4-4
Severity level3
– Surge
EN 61000-4-5 Severity level2
– Conducted interference induced
by high-frequency fields
EN 61000-4-6 Severity level3
– Magnetic fields
EN 61000-4-8 Severity level4
More detailed information on the guidelines,
approvals, and standards is included in the
declaration of conformity.
1 Notes to the user
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

www.balluff.com 5english
2.1 Intended use
The Micropulse Transducer, together with a machine
controller (e.g. PLC), comprises a position measuring
system. It is intended to be installed into a machine or
system. Flawless function in accordance with the
specifications in the technical data is ensured only when
using original BALLUFF accessories. Use of any other
components will void the warranty.
Opening the transducer or non-approved use are not
permitted and will result in the loss of warranty and liability
claims against the manufacturer.
2.2 General safety notes for the position
measuring system
Installation and startup may only be performed by
trained specialists with basic electrical knowledge.
Qualified personnel are those who can recognize
possible hazards and institute the appropriate safety
measures due to their professional training, knowledge,
and experience as well as their understanding of the
relevant regulations pertaining to the work to be done.
The operator is responsible for ensuring that local safety
regulations are observed.
In particular, the operator must take steps to ensure that a
defect in the position measuring system will not result in
hazards to persons or equipment.
If defects and unresolvable faults occur in the transducer, it
should be taken out of service and secured against
unauthorized use.
2.3 Explanation of the warnings
Always observe the warnings in these instructions and the
measures described to avoid hazards.
The warnings used here contain various signal words and
are structured as follows:
SIGNAL WORD
Hazard type and source
Consequences if not complied with
►Measures to avoid hazards
The individual signal words mean:
NOTICE!
Identifies a hazard that could damage or destroy the
product.
DANGER
The general warning symbol in conjunction with the
signal word DANGER identifies a hazard which, if not
avoided, will certainly result in death or serious
injury.
2.4 Disposal
►Observe the national regulations for disposal.
2 Safety
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

6english
3.1 Construction
Electrical connection: The electrical connection is made
via a connector (see Type code breakdown on page 17).
BTL housing: Aluminum housing containing the
waveguide and processing electronics.
Magnet: Defines the position to be measured on the
waveguide. Magnets are available in various models and
must be ordered separately (see Accessories on page13).
Nominal length: To optimally adapt the transducer to the
application, nominal lengths from 50mm to 7620mm are
available.
3.2 Function
The BTL7 transducer contains the waveguide which is
protected by an aluminum housing. A magnet is moved
along the waveguide. This magnet is connected to the
system part whose position is to be determined.
The magnet defines the position to be measured on the
waveguide.
An internally generated INIT pulse interacts with the
magnetic field of the magnet to generate a torsional wave
in the waveguide which propagates at ultrasonic speed.
The component of the torsional wave which arrives at the
end of the waveguide is absorbed in the damping zone to
prevent reflection. The component of the torsional wave
which arrives at the beginning of the waveguide is
converted by a coil into an electrical signal. The travel time
of the wave is used to calculate the position.
This information is transferred via the PROFINET interface.
PROFINET is an industrial bus system based on the
physical layer of the Ethernet (see www.profibus.com).
The transducer can detect and process up to 16magnets.
The maximum number of magnets depends on the
nominal length. The position and velocity of each magnet
can be output.
Implementation is based on the PNO encoder profile V4.1.
The following functions are also available:
– Number of magnets can be parameterized through the
telegram selection. A fixed number from 1to 16 or
flexible (FMM). In FMM, the number of magnets
corresponds to the number of magnets detected, with
a maximum of16
– Setting the resolution of the position and velocity
output
– Reversal of the measuring direction
– Setting presets/offsets
– Temperature sensor. Read out current, minimum, and
maximum temperature.
Synchronous operation with IRT is possible from a cycle
time of 2ms. The minimum possible cycle time is
dependent on the length and configuration.
Supported PROFINET functions:
– RTC class 1 and 3
– RTA (Real Time Acyclic Protocol)
– DCP (Discover and Configuration Protocol)
– CL-RPC (Connectionless Remote Procedure Call)
– LLDP (Link Layer Discovery Protocol)
– SNMP (Simple Network Management Protocol)
– MRP (Media Redundancy Protocol) Client
Fig. 3-1: BTL7... transducer, construction
3 Construction and function
50
40.6
68
41
36.8
~8011.5 ~80~250 ~250
15
88
37
3
2xM12
11.5
M8
1) Unusable area
2) Not included in scope of delivery
3) Groove on the top side of the profile marks
the start of measuring range
1) Nominal length =
Measuring range BTL5-P-3800-2
magnet
1)
Mounting clamps with insulating bushes and
ISO4762M5x22 cylinder head screws,
max. tightening torque 2Nm
2)
2)
Null point
Groove 3)
End point
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

www.balluff.com 7english
3Construction and function (continued)
3.3 LED display
Fig. 3-2: BTL7 LED displays
3.3.1 LED 1: BTL status
LED1 Operating state
Green Normal function
Magnet is within the limits.
Red Error
No magnet or magnet outside the limits.
Tab. 3-1: LED1
LED2
(PROFINET
status)
LED1
(BTL status)
LED3
(Link/Activity
IN)
LED4
(Link/Activity
OUT)
3.3.2 LED2: PROFINET status (dual LED)
LED2
Red
(Bus Failure)
Green Meaning Cause
Off Off No supply voltage
On On No bus connection with other
participants (no link)
Bus not connected
Master cannot be accessed or is switched off
Flashing1) On Bus connection (link) available, but
the sensor is not involved in cyclic
data exchange.
Sensor is starting up, but parameterization has not yet been
completed.
Sensor has been incorrectly configured.
The sensor was assigned an incorrect station address and is thus
not accessible.
The desired configuration is not the same as the sensor
configuration.
Off On The sensor is involved in cyclic data
exchange.
1) Flashing frequency is 0.5Hz. The signal is shown for at least 3s.
Tab. 3-2: LED2
3.3.3 LED3/LED4: Link/Activity
LED3/LED4
Green
Status Connection
On Port open Yes
Flashing Requested by the master
to identify the device
Yes
Off Port closed No
Tab. 3-3: LED3/4
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

8english
4.1 Installing the transducer
NOTICE!
Improper installation
Improper installation can compromise the function of the
transducer and result in damage.
►For this reason, ensure that no strong electrical or
magnetic fields are present in the immediate vicinity
of the transducer.
►The recommended spacing for the installation must
be strictly observed.
Any orientation is permitted. Mount the transducer on a
level surface of the machine using the provided mounting
clamps and cylinder-head screws. A sufficient number of
mounting clamps is supplied.
In order to avoid the development of resonant
frequencies from vibration loads, we
recommend arranging the mounting clamps at
irregular intervals.
The transducer is electrically isolated from the machine
with the supplied insulating bushes (see Figure 3-1).
1. Guide the transducer into the mounting clamps.
2. Attach transducer to the base using mounting screws
(tighten screws in the clamps with max.2Nm).
3. Insert magnet (accessories).
The micropulse transducer in profile housing is
suitable both for floating, i.e. non-contacting
magnets (see Figures4-5 to4-9) and for captive
magnets (see Figures4-2 to 4-4).
The distance (L) between the magnets must be at least
65mm.
Fig. 4-1:
L L L
Distance between the magnets
4.2 Captive magnets
The following must be observed when installing the
magnet:
– Avoid lateral forces.
– Connect the magnet to the machine member with a
joint rod (see Accessories on page13).
Fig. 4-2:
66.4
60
1
Dimensions and distances with BTL5-F-2814-1S magnet
Fig. 4-3:
52.5
47.5
1
Dimensions and distances with BTL5-T-2814-1S magnet
Fig. 4-4:
Y
X
1
Dimensions and distances with BTL5-M/N-2814-1S
magnet
BTL5-M-2814-1S BTL5-N-2814-1S
Distance X 48.5mm 57mm
Distance Y 51mm 59.5mm
Tab. 4-1: Distances with BTL5-M/N-2814-1S magnet
4 Installation and connection
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

www.balluff.com 9english
4Installation and connection (continued)
4.3 Floating magnets
The following must be observed when installing the
magnet:
– To ensure the accuracy of the position measuring
system, the magnet is attached to the moving member
of the machine using non-magnetizable screws
(stainless steel, brass, aluminum).
– The moving member must guide the magnet on a track
parallel to the transducer.
– Ensure that the distance A between parts made of
magnetizable material and the magnet is at least
10mm (see Figures4-5 to4-9).
– Maintain the following values for distance B between
the magnet and transducer and for center offsetC (see
Figures4-5 to4-9):
Type of magnet DistanceB1) OffsetC
BTL5-P-3800-2 0.1 to 4mm ±2mm
BTL5-P-5500-2 5 to 15mm ±15mm
BTL5-P-4500-1 0.1 to 2mm ±2mm
BTL6-A-3800-2 4 to 8mm2) ±2mm
BTL6-A-3801-2 4 to 8mm2) ±2mm
1) The selected distance should stay constant over the entire measuring
length.
2) For optimum measurement results, a distanceB of 6 to 8 mm is
recommended.
Tab. 4-2: Distance and offset for floating magnets
Fig. 4-5:
B
C
50+4
A A
55+4
1
Dimensions and distances with BTL5-P-3800-2 magnet
Fig. 4-6:
C
B
A
A
1
61+10
66+10
Dimensions and distances with BTL5-P-5500-2 magnet
Fig. 4-7:
C
B
A A
1
74+4
69+4
Dimensions and distances with BTL6-A-3800-2 magnet
Fig. 4-8:
C
B
A A
1
63+4
58+4
Dimensions and distances with BTL6-A-3801-2 magnet
Fig. 4-9:
B
A
A
C
4
1
81+2
57.5+2
Dimensions and distances with BTL5-P-4500-1
electromagnet (24V/100mA)
The measuring range is offset by 4mm towards
the BTL plug (see Figure 4-9).
Plug with
LED
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

10 english
4.4 Electrical connection
The transducer is connected via a connector.
The pin assignments for the respective version can be
found in Table4-3.
Note the information on shielding and cable
routing.
4.4.1 Connector BTL7-...-C003
Power
31
44
1
22
31
42 3
Fig. 4-10: Pin assignment of connector (view from above on
transducer)
Pin Cable color Signal
1 BN brown 10 to 30 V DC
2 WH white Not used1)
3 BU blue 0V GND2)
4 BK black Not used1)
BUS IN/OUT (data)
Pin Cable color Signal
1 YE yellow TX+
2 WH white RX+
3 OG orange TX−
4 BU blue RX−
1) Unassigned leads can be connected to the GND on the controller side but not to the shield.
2) Reference potential for supply voltage and EMC-GND.
Tab. 4-3: Pin assignment of ...-C003 connector
4.5 Shielding and cable routing
Defined ground!
The transducer and the control cabinet must be
at the same ground potential.
Shielding
To ensure electromagnetic compatibility (EMC), observe
the following:
– Connect transducer and controller using a shielded
cable. Shielding: Braided copper shield with minimum
85% coverage.
– Connector version: Shield is internally connected to
connector housing.
Magnetic fields
The position measuring system is a magnetostrictive
system. It is important to maintain adequate distance
between the transducer and strong, external magnetic
fields.
4Installation and connection (continued)
Power
(pin)
Bus OUT/Port2
(socket)
Bus IN/Port1
(socket)
Cable routing
Do not route the cable between the transducer, controller,
and power supply near high voltage cables (inductive stray
noise is possible).
The cable must be routed tension-free.
Cable length
The maximum cable length when using CAT5e cables is
100m1).
1) Prerequisite: Construction, shielding and routing preclude the effect of any
external noise fields.
Noise elimination
To avoid equipotential bonding - a current flow - through
the cable shield, please note the following:
– Use insulating bushes
– Put the control cabinet and the system in which the
BTL7 is located to the same ground potential.
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

www.balluff.com 11english
5.1 Starting up the system
DANGER
Uncontrolled system movement
When starting up, if the position measuring system is part
of a closed loop system whose parameters have not yet
been set, the system may perform uncontrolled
movements. This could result in personal injury and
equipment damage.
►Persons must keep away from the system's
hazardous zones.
►Startup must be performed only by trained technical
personnel.
►Observe the safety instructions of the equipment or
system manufacturer.
1. Check connections for tightness and correct polarity.
Replace damaged connections.
2. Turn on the system.
3. Check measured values and adjustable parameters
and readjust the transducer, if necessary.
Check for the correct values at the null point
and end point, especially after replacing the
transducer or after repair by the manufacturer.
5.2 Operating notes
– Check the function of the position measuring system
and all associated components on a regular basis.
– Take the position measuring system out of operation
whenever there is a malfunction.
– Secure the system against unauthorized use.
5 Startup
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

12 english
6.1 Accuracy
The specifications are typical values for BTL7-V50T... at
24V DC and room temperature, with a nominal length of
500 mm in conjunction with the BTL5-P-3800-2,
BTL5-P-4500-1, BTL5-P-5500-21), BTL6-A-3800-21),
BTL6-A-3801-21), BTL5-F-2814-1S, BTL5-T-2814-1S,
BTL5-M-2814-1S or BTL5-N-2814-1S.
The BTL is fully operational immediately, with full accuracy
after warm-up.
For special versions, other technical data may
apply.
Special versions are indicated by the suffix -SA
on the part label.
Position resolution 1µm
Non-linearity with a constant distance
between the magnet and profile:
Nominal length ≤5500mm
Nominal length >5500mm
±30µm
±0.02%FS
Hysteresis ≤±10µm
Repeat accuracy ≤±5µm
(typ. ±2.5µm)
Temperature coefficient2) ≤18ppm/K
Velocity resolution 0.1mm/s
Min. detectable velocity 1mm/s
Max. detectable velocity 10m/s
6.2 Ambient conditions3)
Operating temperature −40°C to +85°C
Storage temperature −40°C to +100°C
Relative humidity <90%, non-condensing
Shock rating
per EN60068-2-274)
150g/6ms
Continuous shock
per EN60068-2-294)
150g/2ms
Vibration
per EN 60068-2-64)
20g, 10 to 2000Hz
Degree of protection per
IEC60529
Connector C003 (when
attached)
IP67
6.3 Supply voltage (external)
Voltage, stabilized5) 10 to 30VDC
Ripple ≤0.5VSS
Current draw (at24VDC) ≤120 mA up to 1524 mm
≤160 mA from 1525 mm
Inrush current ≤500mA/10ms
Reverse polarity protection Up to 36V
Overvoltage protection Up to 36V
Dielectric strength
(GND to housing)
500VAC
6.4 Output
Short-circuit resistance Signal cable to GND
6.5 Dimensions, weights
Housing height 36.8mm
Nominal length 50 to 7620mm
Weight (depends on length) Approx. 1.4kg/m
Housing material Anodized aluminum
6.6 Maximum sampling rate fmax
At nominal length
0050 to 0250mm
0251 to 0600mm
0601 to 1300mm
1301 to 2700mm
2701 to 5500mm
5501 to 7600mm
>7601mm
780Hz
710Hz
600Hz
460Hz
245Hz
180Hz
170Hz
1) In the position range 0 to 20mm, the specified linearity limit can be
exceeded by ±100 µm.
2) Nominal length=500mm, magnet in the middle of the measuring range
3) For : Use in enclosed spaces and up to a height of 2000m above sea
level.
4) Individual specifications as per Balluff factory standard
5) For : The transducer must be externally connected via a limited-
energy circuit as defined in UL61010-1, a low-power source as defined in
UL60950-1, or a class 2 power supply as defined in UL1310 or
UL1585.
6 Technical data
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

www.balluff.com 13english
7.1 Captive magnets
BTL5-M/N-2814-1S
Y
28
22 41
Ø 2
20
X
M5
Fig. 7-1: Installation dimensions of BTL5-M/N-2814-1S magnet
BTL5-M-2814-1S BTL5-N-2814-1S
Distance X 12.5mm 15mm
Distance Y 21mm 23.5mm
Weight: Approx. 32g Approx. 35g
Housing: Anodized aluminum Anodized aluminum
Slide surface: Plastic Plastic
BTL5-F-2814-1S
30.4
28
22
M5x10
±18°
24
40
Fig. 7-2: Installation dimensions of BTL5-F-2814-1S magnet
Weight: Approx. 28g
Housing: Anodized aluminum
Slide surface: Plastic
BTL5-T-2814-1S
16.5
11.5
28
22 40
M5x10
Fig. 7-3: Installation dimensions of BTL5-T-2814-1S magnet
Weight: Approx. 28g
Housing: Anodized aluminum
Slide surface: Plastic
7.2 BTL2-GS10-_ _ _ _-A joint rod
Fig. 7-4: BTL2-GS10-_ _ _ _-A joint rod
Weight: Approx. 150g/m
Material: Aluminum
1) State the nominal length when ordering
Example: BTL2-GS10-0100-A (nominal length = 100mm)
7 Accessories
Nominal length1)
Mechanically attached to
the M5 threaded rod with
2nuts
Adjustment range −5mm
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

14 english
7.3 Floating magnets
BTL5-P-3800-2
38
28
9
14
Ø 4.2
Fig. 7-5: Installation dimensions of BTL5-P-3800-2 magnet
Weight: Approx. 12g
Housing: Plastic
BTL5-P-5500-2
55
28
16
45
21
Ø 4.2
20
15
Fig. 7-6: Installation dimensions of BTL5-P-5500-2 magnet
Weight: Approx. 40g
Housing: Plastic
BTL6-A-3800-2
21
10.813
28.8
28
16
37.6
Ø 4.2
Fig. 7-7: Installation dimensions of BTL6-A-3800-2 magnet
Weight: Approx. 30g
Housing: Plastic
BTL6-A-3801-2
28
16 21
37.6
Ø 4.2
18
13
Fig. 7-8: Installation dimensions of BTL6-A-3801-2 magnet
Weight: Approx. 25g
Housing: Plastic
BTL5-P-4500-1
16.5
45
25
28
15
Ø 4.2
25
7.5
M5x8
40
Fig. 7-9: Installation dimensions of BTL5-P-4500-1 magnet
Weight: Approx. 90g
Housing: Plastic
Operating temperature: −40°C to +60°C
Special advantage of the BTL5-P-4500-1 magnet: Several
magnets on the same transducer can be separately
switched on and off electrically (actuation with a PLC
signal).
7Accessories (continued)
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

www.balluff.com 15english
7Accessories (continued)
7.4 Connector
7.4.1 Power cable, preassembled with straight
M8 plug
– Straight or angled connector, molded, preassembled
– M8 socket, 4-pin
32.2
Ø max. 5
M8x1
Ø 9.7
Fig. 7-10: Connector - straight socket
Type Ordering
code
BCC M314-0000-10-014-PS0434-020
BCC M314-0000-10-014-PS0434-050
BCC M314-0000-10-014-PS0434-100
BCC02N5
BCC02N6
BCC02N7
Examples:
BCC M314-0000-10-014-PS0434-020 = cable length of
2m
BCC M314-0000-10-014-PS0434-050 = cable length of
5m
7.4.2 Power cable, preassembled with angled
M8 plug
Ø max. 5
Ø 9.718.2
M8x1
27
Fig. 7-11: Connector - angled socket
Type Ordering
code
BCC M324-0000-10-014-PS0434-020
BCC M324-0000-10-014-PS0434-050
BCC M324-0000-10-014-PS0434-100
BCC02NH
BCC02NJ
BCC02NK
Examples:
BCC M314-0000-10-014-PS0434-020 = cable length of
2m
BCC M314-0000-10-014-PS0434-050 = cable length of
5m
7.4.3 Data cable, preassembled with M12 plug
– Straight connector, molded, preassembled
– M12 plug (I), M12 plug (II), 4-pin
III
48.5 48.5
M12x1
Ø 14.5
M12x1
Ø 14.5
Ø max. 7
Fig. 7-12: Straight–straight connector
Type Ordering
code
BCC M414-M414-6D-331-PS54T2-020
BCC M414-M414-6D-331-PS54T2-050
BCC M414-M414-6D-331-PS54T2-100
BCC M414-M414-6D-331-PS54T2-200
BCC04K1
BCC04K2
BCC04K3
BCC04K4
Examples:
BCC M414-M414-6D-331-PS54T2-020 = cable length of
2m
BCC M414-M414-6D-331-PS54T2-050 = cable length of
5m
7.4.4 Data cable, preassembled with RJ45 plug
– Straight connector, molded, preassembled
– M12 plug (I), RJ45 plug (II), 4-pin
III
48.5 54.7
18.6
14
M12x1
Ø 14.5
Ø max. 7
Fig. 7-13: Straight–straight connector
Type Ordering
code
BCC M414-E834-8G-668-PS54T2-020
BCC M414-E834-8G-668-PS54T2-050
BCC M414-E834-8G-668-PS54T2-100
BCC M414-E834-8G-668-PS54T2-150
BCC M414-E834-8G-668-PS54T2-200
BCC04K7
BCC04K8
BCC04K9
BCC04ZJ
BCC04KA
Examples:
BCC M414-E834-8G-668-PS54T2-020 = cable length of
2m
BCC M414-E834-8G-668-PS54T2-050 = cable length of
5m
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

16 english
7.4.5 Straight data plug, freely configurable
– Straight or angled connector, freely configurable
– M12 plug, 4-pin
~70
18 16 13
Ø 20
M12x1
Fig. 7-14: Connector - straight plug
Type Ordering
code
BCC M474-0000-2D-000-51X475-000 BCC03WZ
7.4.6 Angled data plug, freely configurable
Ø 20
M12x1
~64
~42
18
18
Fig. 7-15: Connector - angled plug
Type Ordering
code
BCC M484-0000-2D-000-51X475-000 BCC03Y0
7Accessories (continued)
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

www.balluff.com 17english
8 Type code breakdown
BTL7 - V 5 0 T - M0500 - P - C003
Micropulse transducer
Ethernet interface
Supply voltage:
5 = 10 to 30VDC
Output gradient:
0 = Configurable
Ethernet interface type:
T = PROFINET
Nominal length (4-digit):
M0500 = Metric specification in mm, nominal length 500mm (M0050 to M7620)
Construction:
P = profile housing
Electrical connection:
C003 = 4-pin, 1 x M8 plug + 2 x M12 plug, D-coded
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing

18 english
9.1 Converting units of length
1 mm = 0.0393700787 inches
mm inch
1 0.03937008
2 0.07874016
3 0.11811024
4 0.15748031
5 0.19685039
6 0.23622047
7 0.27559055
8 0.31496063
9 0.35433071
10 0.393700787
Tab. 9-1: Conversion table mm to inches
1 inch = 25.4 mm
inch mm
1 25.4
2 50.8
3 76.2
4 101.6
5 127
6 152.4
7 177.8
8 203.2
9 228.6
10 254
Tab. 9-2: Conversion table inches to mm
9 Appendix
9.2 Part label
Fig. 9-1: BTL7 part label
1) Ordering code
2) Type
3) Serial number
4) Null mark
1)
3)
2)
4)
3)
BTL7-V50T-M ____-P-C003
Micropulse Transducer in a Profile Housing