manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Band-it
  6. •
  7. Power Tools
  8. •
  9. Band-it C003369 User manual

Band-it C003369 User manual

BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
Document # P91687 Rev. I.1
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
www.BAND-IT-IDEX.com
Page 1 of 4
C00369 Heavy Duty
Hand Tool
Operating
Instructions
Safety Practices:
1. Read this manual and become familiar with the tool before use.
2. Protective eyewear should be worn during use.
3. Wear appropriate gloves for handling steel.
4. When applying clamps, care should be taken to insure fingers are not in contact with
the clamp during installation.
5. Never attempt to clamp objects which have the potential to burst, shatter or
otherwise cause bodily harm.
6. Do not use tool on live electrical sources.
Introduction:
The C00369 Tool installs any BAND-IT Band of .030" thickness or less and 3/4" Giant
Band of .044" thickness.
Table of Contents:
1. Introduction & Safety Practices
2. Operating Instructions
3. Tool Assembly Parts List
4. Cleaning & Warranty
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
Document # P91687 Rev. I.1
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
www.BAND-IT-IDEX.com
Page 2 of 4
C00369 Heavy Duty
Hand Tool
1. Slide buckle on band as shown.
Bring tip of band around workpiece
and again through buckle.
Note: Band may be used from bulk roll
as this completely eliminates waste of
band.
2. Insert band around workpiece
again and through buckle. Double
wrapping develops much more radial
compression than single wrapping.
Bend end of band under buckle.
3. Place band in opening of tool nose
and Gripper Block. Move into slot as
far as possible, to avoid buckle sliding
into Tool Nose. Tighten band clamp by
turning the Tension Handle clockwise
while holding Band Gripper tight against
band. NOTE: The spring load of the
band gripper is not intended to secure
and prevent the band from slipping
during tension process.
4. Place finger on BAND-IT Band at
buckle bridge while tensioning. When
you observe the band stops moving
through the buckle, maximum pressure
is being exerted around the workpiece.
Stop turning handle.
5. Roll tool over buckle, backing off
with Tension Handle 1 - 1½ turns
throughout entire rolling operation.
Failure to back off tension with tension
handle throughout roll-over may result
in breaking the band. There is no loss
of tension as band released is used up
in this process.
6. Rotate Cutting Handle forward to cut
the band. When applying Giant Band
clamps, prior to cutting off clamp,
release Band Gripper and push Tool
Nose away from buckle approx. ¼”.
7. Remove tool, holding
stub of band down.
8. Hammer down buckle ears
to complete BAND-IT clamp.
Instruction
Manual
Tool Nose
Gripper Block
Band Gripper
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
Document # P91687 Rev. I.1
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
www.BAND-IT-IDEX.com
Page 3 of 4
C00369 Heavy Duty
Hand Tool
1. To assist in removing threaded
parts, apply heat to soften locking
compound.
2. When connecting item 13 (Set
Screw) to item 14 (Cutter Bar), clean
threads (male and female) of foreign
matter, then apply one drop of
medium strength locking compound
(Loctite 242 or equiv.) onto male
thread and connect parts together.
3. Kit # C01899 contains one each
Band Gripper, one Gripper Spring and
one Pin. Replace all parts as a set to
maximize tool performance. Periodic
cleaning of band gripper teeth will
improve tool performance.
C00369 PURCHASABLE REPAIR KITS
KIT #
ITEM #s
DESCRIPTION
C04799
5, 6, 7, 8, 15
SPIN GRIP (2), EXTERNAL RETAINING
RING (2), TENSION HANDLE BUSHING,
TENSION HANDLE, SET SCREW,
THRUST BEARING
C06799
10, 1, 3, 2, 16
TENSION SCREW 5/8”, ECCENTRIC
LEVER PIVOT PIN, GRIPPER SPRING,
BAND GRIPPER, SLIDE BLOCK
C05887
11, 12, 13, 14
CUTTER BAR HANDLE, VINYL GRIP,
SET SCREW, CUTTER BAR
Tool Assembly
Parts List
3
2
1
4
8
12
11
14
15
6
9
10
5
7
13
16
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-0307 USA
P: 1-800-525-0758
F: 1-800-624-3925
Document # P91687 Rev. I.1
© Copyright
BAND-IT-IDEX, Inc. 2010
All rights reserved
www.BAND-IT-IDEX.com
Page 4 of 4
C00369 Heavy Duty
Hand Tool
Cleaning &
Warranty
Gripper Cleaning Instructions:
1. To remove Gripper, align
Gripper Pin hole with notch in
tool frame. Using a punch and
hammer, punch Pin out of
Slide Block.
2. Using a wire brush, clean all
foreign matter from teeth.
3. To replace Pin, Gripper
Spring must be seated in
Tension Screw hole. Align
Gripper hole with Slide Block
hole and insert Pin using a
hammer.
Refer to website for warranty information: http://www.band-it-idex.com/warranty.html
NOTE: Periodically apply food-grade white lubricant or equivalent to Tension Screw thread (item
10 on page 3) to prevent excessive wear.
If tool fails to securely grip tail of clamp, follow Gripper cleaning instructions above.

This manual suits for next models

1

Other Band-it Power Tools manuals

Band-it T30069 User manual

Band-it

Band-it T30069 User manual

Band-it Ultra-Lok UL9010 User manual

Band-it

Band-it Ultra-Lok UL9010 User manual

Band-it G40269 Giant II User manual

Band-it

Band-it G40269 Giant II User manual

Band-it Ultra-Lok UL4000 User manual

Band-it

Band-it Ultra-Lok UL4000 User manual

Band-it A35199 User manual

Band-it

Band-it A35199 User manual

Band-it C00169 User manual

Band-it

Band-it C00169 User manual

Band-it GRG402 Giant II User manual

Band-it

Band-it GRG402 Giant II User manual

Popular Power Tools manuals by other brands

jbc T210 Series instruction manual

jbc

jbc T210 Series instruction manual

Campbell Hausfeld DG460300CK S Operating instructions and parts manual

Campbell Hausfeld

Campbell Hausfeld DG460300CK S Operating instructions and parts manual

Hilti SJT 6-A22 Original operating instructions

Hilti

Hilti SJT 6-A22 Original operating instructions

EINHELL TC-JS 18 Li Original operating instructions

EINHELL

EINHELL TC-JS 18 Li Original operating instructions

DeWalt XR Li-Ion DCF813 instruction manual

DeWalt

DeWalt XR Li-Ion DCF813 instruction manual

Cleco 48EAE51P3 instruction manual

Cleco

Cleco 48EAE51P3 instruction manual

Sioux Tools 2 1/2 Series instructions

Sioux Tools

Sioux Tools 2 1/2 Series instructions

Hitachi V-550 B Operation manual

Hitachi

Hitachi V-550 B Operation manual

Greencut PRE10000 instruction manual

Greencut

Greencut PRE10000 instruction manual

Juxta VJ77 user manual

Juxta

Juxta VJ77 user manual

Baileigh TN-800 Operator's manual

Baileigh

Baileigh TN-800 Operator's manual

Kyocera TJEP FH 21/90 LW quick start guide

Kyocera

Kyocera TJEP FH 21/90 LW quick start guide

Bosch MXH180B Operating/safety instructions

Bosch

Bosch MXH180B Operating/safety instructions

Bauer 22201E-B user manual

Bauer

Bauer 22201E-B user manual

Festool PSC 420 EB Original operating manual

Festool

Festool PSC 420 EB Original operating manual

Erbauer ERB706SA manual

Erbauer

Erbauer ERB706SA manual

Delphi Ceramic Kiln instruction manual

Delphi

Delphi Ceramic Kiln instruction manual

Bavaria BJS 650 E Original operating instructions

Bavaria

Bavaria BJS 650 E Original operating instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.