B&B Electronics Elinx EIR510 Series User manual

EIR510 Series-5107qsg
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
815-433-5100 Fax [phone] www.bb-elec.com [email protected] [email protected]
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
[phone] Fax [phone] www.bb-europe.com [email protected] [email protected]
Items Included
1
2
Default Settings
3
LED Chart
4
Hardware Installation
Log into the Switch
5
oEthernet Switch
oConsole Cable (RS-232 RJ-45 to DB-9)
oCD with Support Manual
oThis Quick Start Guide
oPanel Mount Bracket
oIP Address: 192.168.16.1
oSubnet Mask: 255.255.255.0
oGateway: 192.168.16.254
oUser Name: root, Password: root
LED Status Meaning
Green The Switch is powered on
PWR Off The Switch is powered off
Green Power Source 1 is available
PWR1 Off Power Source 1 is unavailable
Green Power Source 2 is available
PWR2 Off Power source 2 is unavailable
Orange A power or port failure has occurred
Fault Off Normal Operation
Green The Switch is the master of a redundant
ring (X-Ring)
R.M Off The Switch is not the master of a
redundant ring.
Green The port is linked
Blinking Data is being transmitted or received
LINK/ACT
(P9/P10) Off Not connected to the network
Top Green Connected to the network
Top Blinking Transmitting or receiving
Top Off Not connected to the network
Bottom Orange Operating at full-duplex
Bottom Blinking Collision
P
1-8
Bottom Off Half-duplex or not connected
oRecord the switch’s MAC Address in the space
provided. Provide the MAC Address to your Network
Administrator. The Network Administrator will
provide an IP Address, Subnet Mask and Gateway.
oSelect a mounting location and install with the attached
DIN rail clip or included panel mount kit.
oConnect power to the switch
o24 to 48 VDC
oRedundant inputs are available with fault
contacts.
oThese instructions are for Web based management.
Refer to the User’s Manual for instructions concerning
console management.
oConnect a stand alone PC to a port on the switch.
Change the PC’s network IP Address to allow it to
connect to the switch (ex: 192.168.16.2). Use the
default subnet mask and gateway.
oLaunch the PC’s web browser and navigate to the
switch by typing the switch’s IP address in the browser
address window.
oNavigate the web page by expanding the folders on the
left side of the web page.
Quick Start Guide
Elinx Managed Ethernet Switch
EIR510 Series

EIR510 Series-5107qsg
International Headquarters: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA
815-433-5100 Fax [phone] www.bb-elec.com [email protected] [email protected]
European Headquarters: Westlink Commercial Park Oranmore Co. Galway Ireland
[phone] Fax [phone] www.bb-europe.com [email protected] supp[email protected]
IP Configuration
User Name and Password
76
oExpand the “system tree” and select IP configuration.
oEnter the IP Address, Subnet Mask, and Gateway
provided by your Network Administrator.
oSave the changes.
oDisconnect the stand alone PC from the switch and
connect the switch to the network.
oInform the Network Administrator that the IP Address
has been changed.
oNOTE: The User Manual contains instructions for
configuring the IP Address from a DHCP Server and
to allow the switch to act as a DHCP Server.
oThis step should be performed by the Network
Administrator.
oLog onto the switch from a PC connected to the
network.
oExpand the “System Tree” and select user
authentication..
oEnter the new User Name and Password. Record this
information in the space provided below. File this
document for future reference.
oClick the Apply button.
USER NAME: ______________________________________
PASSWORD:_______________________________________
MAC ADDRESS: ____________________________________
IP ADDRESS: _______________________________________
Basic Configuration is complete. A
comprehensive Manual is contained on the CD
ROM. Refer to this manual to configure the
advanced features of this switch.